JBL Xtreme Li-ion Battery Mod - The Right Way

Подписаться 33 тыс.

Просмотров 95 тыс.

50% 1

Need a new battery for the JBL Xtreme bluetooth speaker?
In my case i got a used one from Ebay where the battery was dead. It didn't charge anymore, and it was out of warranty.
I was going to try to convert it to Li-ion batteries the same way as they are used in the JBL Xtreme 2.
Found and old broken laptop battery with 6 18650 cells in it. Took that apart, and was able to recover four good batteries from that pack.
Now they are in the Xtreme, and they are doing a good job. Charging works again, and the Xtreme frame needed only a small modification in order to fit the new batteries.
Have a look, share, comment, like, watch and learn!

Хобби

Опубликовано:

13 июн 2018

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 241

@joachim9805 6 лет назад

This is clean. Good job

@TaylorSoloaiJR 6 лет назад

I used 18650s too but only difference between your method and mine is that I didn't have to MOD the battery compartment. But I like how you made batteries look like they came out of a factory, looks a lot more cleaner and neat compared to mine. Awesome work!

@mygiguser 6 лет назад

Taylor Soloai my batteries didn’t fit without modifying the case. There was a 1-2mm gap when you put the lid on, and you try to avoid any physical pressure on those batteries. Then again, as long as it works.

@pinkpenguin7880 6 лет назад

Nice job. Great idea to reuse some old batteries that are still good! Voted 👍

@georgebush5769 11 месяцев назад

Sorry for the very very late reply. Just want to say thank you for sharing your video. I was able to gain knowledge and experience. Especially during the replacement of the battery of my jbl extreme speaker got from my father in law. Now i have two of them the other one was the jbl boombox. I did the same.

@jozensenz 4 года назад

Thnx for the gread video i was able to fix ky jbl xtreme that i had put a way for a year.

@harmindersingh7833 4 года назад

Great ideas sir

@angy689973 5 лет назад

I made the change, it was running for 8 hours, but when I plugged in is going to the 5th led and blinking non stop.I removed the charger and is not turning on animore. Is turning on only when you plugged in the charger.Help please !

@allancanada552 5 лет назад

So good..i follow wat u do and its work it..thankyou so much sir..here in phillippines

@genesismanalang7946 5 лет назад

hndi nmn ba mabilis masira paps?

@lafflagabelonio6097 4 года назад

ako naman jbl charge2 kinuha ko lang yung board sa lumang battery. isang 18650 na batt with 3.7V so far so good hehe

@mikeandrolopez5231 4 года назад

Boss 18650 b n 3500 mah at anong brand?TIA

@vincentsarian7214 4 года назад

I already replaced with 18650 battery but the problem i already charge it for 12 hours still it wouldn't got full what's seems to be the problem?

@mimaomao9993 3 года назад

THANK YOU! I T WAS VERY HELPFUL.

@kassiodourado8588 5 лет назад

Boa noite eu sou brasileiro e achei seu vídeo muito bom o melhor do RU-vid parabéns

@mygiguser 4 года назад

Obrigado!

@tosejancevski8680 2 года назад

Do you get JBL xtreme distortion at full volume.? i got some distortion . sounds like clipping,after battery replacement 18650.But only when i listen music on yotube music or songs from my phone with hight quality 320kbps

@rosariosalvador8079 5 лет назад

mygiguser can i use 21700 or 20700 batteries for that mod?for more runtime.

@javiarji8980 5 лет назад

Thanks

@angset 3 года назад

Do you need to know about Mah or not when you want to install it ?

@kieranrichards7458 Год назад

Hi, thank you for this demonstration! I have done the above with some Samsung 3500mAh batteries. How have your batteries held up? Are they still keeping a charge after 4 years? Ive noticed when charging mine that the indicators go from 1-4 very quickly and also from 4-1 very quickly. Have you noticed that your battery level indicator is now less accurate?

@mygiguser Год назад

not really, mine still works great. Make sure you have real Samsung batteries, there are counterfeit cells out there. And it takes only one bad cell in the pack to make the battery pack behave weird. And what do you mean by very quickly? How long does it take?

@JavierNallar 5 лет назад

Hello, after the mod I got a little distortion on the side of the pasive radiator that is taken out when reaching low frequencies, what could it be. I tried to tighten up the bolts that hold it as muchs as i can and it seems it helped a little but I cant figure out what reaaly could be the problem.

@MortenBN1988 5 лет назад

Wires touching surfaces can cause distortion/rattle..

@tosejancevski8680 2 года назад

What firmware version is the best for jbl xtreme ?

@keyvan560 2 года назад

Thank you so much for this video , what diffrence between your way and other way i found at youtube ?that video i saw , 2 batteries conected to buttun bms and 2 more batteries conected another + and - at up on bms , your diagram is diffrence , sorry for my bad english , after 3 yaers works perfectly ?

@mygiguser 2 года назад

Mine still works great

@erik3533 5 лет назад

Nice work! Can you see any problems with having more batteries installed? I'm planning too putt batteries, in both sides under the air thingy, aswell as we're you put youre batteries, will the charger mange it? I know the sound quality can be an issue... I just want to maximize the battery life, for like festivals or camping usage. Great video!

@mygiguser 5 лет назад

If you add batteries in parallel, that shouldn't matter as long as you don't run out of space inside. I am sure the sound will change, if you use up all the space inside the speaker.

@WCxColosus 5 лет назад

i was planning on doing thia to increase the capacity i just wanted to add 2 more. i have 3000 mah batteris so if i wire in parallel that geta me up to 6000 if i add another 2 that gets me to 9000 right??

@rogersbonettmb 3 года назад

Thanks for this video. I'm just wondering how to do a li ion battery pack with negative, positive and data cable as well. My Sony XB30 bluetooth speaker has 3 connectors on the battery port. What happens if I make the battery pack without that third (yellow) port?

@mygiguser 3 года назад

you need to build the battery the same way the old one was. the 3rd connector may be for temperature monitoring, and the whole thing may not work without. But the XB30 battery is already made from 18650s? Does it make sense to just buy a new battery pack?

@rogersbonettmb 3 года назад

@@mygiguser thank you so much for replying me. I'm not sure if the battery package of my BT speaker is made using 18650 batteries. I just want to know how to make a new package because I found that purchasing a new one is not that easy and to be honest I really like the sound quality of my bluetooth speaker so much that I don't want to throw it away when its battery pack gets damaged.

@megandrannaidoo4102 4 года назад

There are gaps by your battery bay don't you hear distortion sounds?I used silicon and a layer of duct tape on mine does the trick well

@mygiguser 4 года назад

No, i didn't have any distortions. The gap you could close with epoxy.

@BLACK_HEART_1993 3 года назад

I will try this. I have 18650 4x 5000mah..thank for this video..

@mygiguser 3 года назад

there is no such thing a 5000mAh 18650, that sounds fake. Where did you get those from? China?

@BLACK_HEART_1993 3 года назад

@@mygiguser no.. I took from broken samsung laptop. And Ialso have 3500mah

@rejoiceregion1524 2 года назад

@@BLACK_HEART_1993 How is it working for you mine are 4200

@kristian8153 3 года назад

Can you please explain to me the diagram shown at 2:43. This diagram is different from the other vids showing. I just want to know what and why because I don't have any idea. Thanks for answering.

@mygiguser 3 года назад

not sure what there is to explain? how is it different than others? The original battery has two pouches, my setup has 2 sets of 2 batteries in parallel, and the wiring is the same as the original battery pack. And btw this setup works in my speaker since i made the video, and that is 2 years now.

@kristian8153 3 года назад

@@mygiguser thank you so much for responding. Is it okay for those 2 wires in the middle to get in contact with each other? I'm talking about the wire that connects to the green wire. I hope you understand what im saying as I don't really know how to explain it.

@kristian8153 3 года назад

@@mygiguser I'm just currently waiting for the 18650s that I ordered before I do the procedure. I hope I wont blow up my speaker lol

@seyhaheng9045 3 года назад

can you show how to do like this for JBL Bommbox ?

@pablog4584 5 лет назад

Hi! I want to know if this bateries incresed the batry life?

@mygiguser 4 года назад

yes, they do.

@HeinrichvanRooyen 4 года назад

Great video. One question... How did you test the laptop batteries to determine if they are good or bad? Thanks.

@mygiguser 4 года назад

i used an intelligent charger/discharger to charge them one by one. There was only one bad in the whole pack.

@HeinrichvanRooyen 4 года назад

@@mygiguser OK thanks. No easy way that I can check it without fancy equipment? (also using an old laptop's battery and don't want to use cells that are bad)

@advvaibhavvashisht9399 4 года назад

@@HeinrichvanRooyen There is an easy way, youtube it.

@harrisong5023 5 лет назад

Any gain out of doing this? Increased battery life, better sound etc? Also, any downsides? Charging issues, etc?

@mygiguser 5 лет назад

Harrison Gieske no downsides. I hear about a few people having battery issues, this video is to help them.

@aliciadsouza122 4 года назад

Hi bro. Very nice video. Nicely explained. I have one question The original battery is 5000mA 7.2V, I am planning to put 6 no’s of battery, each battery 1.2 V(AA) 1300mA. Battery size 6 no’s fits very well , Is is possible to connect 6 no’s AA battery in series to the circuit?

@skadi7654 2 года назад

no it is too long

@Leovixfull 5 лет назад

Very good, very useful. Would you like to know the battery life and if there was any bass loss? This how much mAh and voltage this managment board has? My original jbl has 10.000mah.

@mygiguser 5 лет назад

Le o don’t know the battery life, no bass loss, and this setup has the same BMB as the original battery.

@Leovixfull 5 лет назад

@@mygiguser Nice. I have 4 batteries with 3.7v and 2600mah. Can i use same managment board as you ?

@akhiltripathi001 2 года назад

Hi! i was doing the same mod for JBL boombox can you help with wiring. It has 4 x 3.7 V cells like xtreme but the BMS have 4 pads 2 B+ and 2 B-. Should i individually connect 2 x 4 cells in parallel and connect them to B+ and B- respecively or need balance lead. Bit confused any help will be appreciated.

@mygiguser 2 года назад

connect the same way as the original battery was connected

@akhiltripathi001 2 года назад

@@mygiguser yes connected 8 Lion cells (Sony VTC6) in 2S2P configuration to make a 14000mAH 7.4v battery pack. The cells where at storage while making the battery pack. After installation it got 100% charged in 2 hours and i have been doing a test from past 12 hours. The backup has increased as still the 5th led has not started blinking. Thanks @mygiguser for the idea.

@jaaa2055 19 дней назад

Hi, can you explain me one thing. when i make 2s with 18650 so the voltge vil be 8.4 v and the charger is 19 V so how this can work ??

@mygiguser 18 дней назад

I made this video 6 years ago, and the speaker still works with the same battery hack. That show me that it works. I don't know how, but the original pouch battery is wired the same way.

@andrewid1976 5 лет назад

How we can use suatable BMS for 18650 ? Original xtreme bms cutting out earler `cose maded for LiPo batts. 18650 will last longer, but need to replace bms as well. Dont know why and for what they use to use 3rd wires after bms. As usual two is enouth. Bms after bms?

@mygiguser 5 лет назад

The third wire is for temperature on the battery pack. If you don't like the original BMS, just replace it with a new one.

@andrewid1976 5 лет назад

@@mygiguser wow - r u shure? Have u tried do not connect it, jbl works fine? I belived 3d wire connected to the middle battery point

@mygiguser 5 лет назад

Did you see the drawing @2:44 in the video? That is how it is connected. The connector to the main board has 5 connectors two GND, two power, and the one in the middle is Temp.

@user-pb6oy6cq1q 5 лет назад

@@mygiguser the green wire with the thermocouple to measure temperature?

@darkovsky 4 года назад

What did you use to cut the piece of plastic that doesn't let 18650s to fit?Should i take care of anything?|I am charging to full at the moment with the speaker assembled, the door doesn't close good so there is air leak and distortion at the bass, i was wondering if would good to mod it, i will check how much it lasts with the 18650s and if is a big improvement then i will go on

@mygiguser 4 года назад

darkovsky i used a Dremel.

@darkovsky 4 года назад

@@mygiguser this is what i thought, thank you

@Serwis_Elektroniki_ 5 лет назад

Important! In this repair need to change the BMS. This one is shitty, does't have temperature sensor on the cells and does't have a ballancer.

@silasvieira4874 5 лет назад

A bateria original são duas células de 7,4v 5000mah em série, então nessa adaptação as baterias vão ficar com 3,7v???

@pedropaulodiasbulhosa3576 2 года назад

Ai tá em paralelo e em série!! Ai vai ficar 7,4v !!

@PeterRichardsandYoureNot 4 года назад

So, perhaps show how you got the case opened up instead of just skipping over it.

@mazzecake 3 года назад

@mygiguser I accidentaly ordered a new battery for the xtreme 2 instead of xtreme. Could I just trim up the battery spot like you did and put in the xtreme 2 one?

@mygiguser 3 года назад

the battery in Xtreme1 has 5 pins, and the battery in the Xtreme2 has 6 pins. So the answer is no. You would have to rewire that new battery pack to get the connector right.

@masterdadventurevlog2250 Год назад

@@mygiguser what is the yellow color in 6 pin xtreme 2? i now the red are positive black is negative and white is temperature but the yellow im confuse.

@pongasiong 5 лет назад

What size of battery wrap did you use on this video?the one you use to make 4 batteries

@mygiguser 5 лет назад

I found it on Amazon: Uxcell a15012900ux0431 PVC Heat Shrink Wrap, for 2 x 18650 Battery, 10 m, 50 mm Width, Red

@kkdamion 4 года назад

@mygiguser can you explain?? why you put the batteries in series and not like the original configuration 2x parallel ?? second question: does the green wire connect on the BMB on both BM contacts??

@mygiguser 4 года назад

@2:44 is the schematic of this, and yes, green wire connects to both contacts.

@mygiguser 4 года назад

The original configuration is 2x parallel? what does that even mean?

@kkdamion 4 года назад

Ok let me change the question so you understand it better , the original configuration was two flat batteries independent connected to the BMB. why did you made one batterypack out of four batteries and not two packs of 2 batteries? And connected them the same way as the flat ones

@Leovixfull 5 лет назад

I have one question. In managment board you have the red positive cable and the black negative cable right? What is that green cable?

@mygiguser 5 лет назад

We have two pair of batteries. Each pair has 3.7V, and the two pairs are wired in series to achieve 7.4V The green wire is the positive of the first pair, and at the same time the ground of the second pair. This is needed to be able to charge both packs to the same level (also called balancing the battery pack).

@Leovixfull 5 лет назад

@@mygiguser okkkkk now i undestand. I'll do tomorrow than ill feedback here. Thank you very much

@job4032 4 года назад

Ok. I've seen people with that it keeps blinking with the fifth led. Why is that and what could you do about it?

@mygiguser 4 года назад

Well when you have a brand new great battery this charge indicator may work. Once the battery was in use for a while it is more and more likely that the 5th LED stays on, because that kind of battery looses its capability to charge 100%. And the 5th LED shows the 100%. I don't think it is a big deal.

@yashdobra9154 4 года назад

Hey giguser thnx for the help my jbl works properly now, for increased battery life instead of 4 I placed 8 batteries (4on each side) Jst one issue when charging after 30 mins the 4th led starts blinking and after tht it reaches the 5th led then 1hr later again 4th led starts blinking and it goes on forever. While playing I get a very large playback time, but how would I knw tht batteries are fully charged coz 4th led starts binking and goes on forever also would like to knw is there anything other wrong with it coz my batteries I used were of good quality

@mygiguser 4 года назад

I don't know, maybe the battery board is too small for that many batteries?

@piyushrawat8632 3 года назад

Same problem with my JBL

@berkebecerikli5480 4 года назад

Should ı buy a new charger after the change battaries for speaker?

@mygiguser 4 года назад

@Serwis_Elektroniki_ 4 года назад

1:39 Those magnet does not conduct electricity. Therefore, there is no insulation on the connectors :D

@miko192837 4 года назад

I did the same but I have no tension on the balancer output why?

@mygiguser 4 года назад

Good question

@miko192837 4 года назад

it turned out that the batteries were not charged enough, does it close normally?I can't close the battery compartment

@scalabreza 6 лет назад

Hi. I'm looking forward to doing this with the JBL Charge 3. Are there any circuit schematics, using panasonic batteries to help? Thank you

@mygiguser 6 лет назад

Not sure, i don't own a Charge 3.

@scalabreza 6 лет назад

mygiguser, thank you man! Nice

@carlitoboquila5267 5 лет назад

@@scalabreza man i have jbl charge 3. I have problem my battery because its getting big.. It is because of over charge??

@lainux4875 4 года назад

@@carlitoboquila5267 its because theres pressure inside the battery, u definitely have to change it, could explode while charging/using

@yashdobra9154 5 лет назад

The battery compartment is not closing fully not any space left so is there another way that I could put some hot glue from outside to stop air leakage ??

@mygiguser 5 лет назад

Yash Dobra that’s why i removed some of the housing. i show that in the video. if you use hot glue then you have trouble later in case you have to replace those batteries next time!

@yashdobra9154 5 лет назад

@@mygiguser yes now I see I would remove some of the housing and then I m sure they all will fix and the compartment will be tight when closed and no air will escape, followed ur instructions dude. Keep it up the pro. Battery pack idea is awesome keep it up and thnx for making my day 😇

@lakhon9912 5 лет назад

How many hours can you listen to

@YehezkielLee 2 года назад

hi,do anyone know solutiom for xtreme 2?,because theres a yellow and white cable,the white cable with 10k resistance not works,been changing the battery cell with original bms board but the bms didnt showing output power

@mygiguser 2 года назад

the xtreme 2 has already Li-ion batteries, you can buy a complete pack with bms

@YehezkielLee 2 года назад

the battery itself here was way to overprice, the price of the battery are like as the speaker itself sir,cant turn the speaker without battery😢

@YehezkielLee 2 года назад

is there a way to use the speaker without battery,sir???

@tosejancevski8680 2 года назад

jbl xtreme slow charging after 18650 battery 2600 mah panasonic replacement, what"s the problem?

@mygiguser 2 года назад

what do you mean by extremely slow? is your power supply ok? how did you wire this (same as in video?)?

@tosejancevski8680 2 года назад

@@mygiguser after 10 hours charging last diode of indicator still blink, power supply is ok,wire is same as in video. how many hours do you need to charge you speaker after upgrade 18650 batteries?

@flaviualinpustan7589 Год назад

How did you manage to solder the wires to the BMS module? Solder doesn't stick to those plates when I try to solder them.

@mygiguser Год назад

it should stick, no problem here

@mygiguser Год назад

You need to solder the battery ends off that board, heat it up with the soldering iron, and remove them first.

@flaviualinpustan7589 Год назад

@@mygiguser Thank you.

@lafflagabelonio6097 4 года назад

is it safe to open the bloated battery of my jbl charge 2? not entirely the lithium itself.. just only the shrink case plastic that wraps around it. i was also going to try this method instead of buying new battery. i find it so expensive. thanks.

@mygiguser 4 года назад

Lafflaga Belonio NO, that is not safe at all. if it is bloated you MUST replace that battery!!!

@lafflagabelonio6097 4 года назад

@@mygiguser ok sir thanks for the advice!

@pongasiong 5 лет назад

After ive done this, when fully charged, the led lights are not lit anymore, is that normal?

@mygiguser 5 лет назад

Jay ar Zamora only if the batteries are fully charged. Otherwise some should be on while charging.

@lafflagabelonio6097 4 года назад

update on jbl charge2. i was able to salvage d pcb board on the swollen lithium ion battery of my jbl charge2. at first i was very hesitant and afraid to remove the board. i carefully peeled the shrink tube that was covering the battery also tried not to damage the body of the lithium battery to avoid sudden fire. well im very thankful that nothing happened that time. i swapped the old battery with a single 18650mAh 3.7V. as of this moment my speaker is working again.. i suggest not try or risk the same way i did if you dont have any small knowledge about electronics.

@burakterzi5253 3 года назад

I did it. But the cable burned out. Which cable we need to use is the vehicle wiring cable?

@mygiguser 3 года назад

you did what? and what vehicle wiring cable? what cable burnt out?

@burakterzi5253 3 года назад

@@mygiguser I used a thin cable.I made the wrong arrangement short circuit

@mh7711 5 лет назад

U said there are ready to buy batteries for replacement but i only find Lithium Polymer batteries, that are different batteries, LiIon like u use have much more lifetime even if you store it with 100%. :)

@mygiguser 4 года назад

That's correct, but if you buy a ready made pack, you don't have to modify the case and you don't need to solder. Not everybody wants to do that.

@techman6431 2 года назад

I did without cut internal body just punched n screwed no air leak working perfect from india

@alvinalarcon6032 4 года назад

I have a problem with my jbl xtreme I just bought a battery for my jbl it won't charge up at all and it won't play unless it's plugged in and even then it still turns off, and just to let you know it was doing this before I put a new battery. So please help me what do you think is going on with it?

@mygiguser 4 года назад

If it is not the battery then it could be the power supply? Can you check the voltage when the power supply is attached? Maybe it doesn't have enough power?

@mrmusic7068 3 года назад

Defective battery

@franzi8 Месяц назад

Warum haben sie den bm anschluss gebruekt ???

@karimwahsh5474 11 месяцев назад

Hey, I’m trying to do the same with the boombox 1 and i found they are 4 cells not 2 and the BMS is like a double of the one on the xtreme so could you please tell me how to connect? Should i get 8 batteries 18650 ? Or only 4 ? Please help

@mygiguser 11 месяцев назад

doesnt boombox one have 18650s? i think its safe to get a new battery of ebay.

@karimwahsh5474 11 месяцев назад

No it’s not unfortunately it’s liPO battery i guess

@karimwahsh5474 11 месяцев назад

Could you please send me your facebook profile or anything so we can chat on ?

@johnlee1101 4 года назад

Not sure the batteries setup, BM combine to top and bottom, how the chip know the batteries are balance?

@mygiguser 4 года назад

John Lee when wired in parallel, they balance themselves.

@mygiguser 4 года назад

Keep in mind, this pack consists of 4 batteries, that is two pairs. The battery board you need to use will balance one pair with the other pair.

@joseramosramos3082 5 лет назад

Dear, it is assumed that when installing the batteries has more mA than the origianal, how does the led behave according to the load? Is there a problem if I install samsung batteries 18650 3500mA? How long is the battery life in operation with the new arrangement?

@mygiguser 5 лет назад

Jose Ramos Ramos no problem with the LED charge indicator, it is based on battery voltage. The more Ah the new batteries have the longer they last. Battery lifetime is hard to say, it depends on the battery quality. I think Samsung is pretty solid.

@kyteyt2166 3 года назад

I will use 26650 3.7 volts with 5000mah.base on your drawing i will connect only the blue and red?no need the green?

@mygiguser 3 года назад

26650 doesnt fit, and why are you questioning the green? Green is shown in the schematic because it is necessary. I dont understand why you question that? Also 5000mAh may be too much for the BMS, the max for a 18650 is 3000mAh as far as i know, everything higher is fake.

@kyteyt2166 3 года назад

@@mygiguser because i will use only single battery..26650 5000mah

@SafeShifter 5 лет назад

Nice work man. Can I follow the same method for my Harmon Kardon Go Play? Can you do a video on HK GoPlay battery upgrade too?

@mygiguser 5 лет назад

banubash not sure, i don’t have that speaker

@WCxColosus 5 лет назад

i bought some to do on my charge 3 im confused on the rating of the batteries they are rated at 3000 mah 3.7v is that each cell or for both?

@mygiguser 5 лет назад

WCxColossus each cell

@WCxColosus 5 лет назад

@@mygiguser so with 2 cells ill be at stock mah for my charge 3?

@nytrhythm 4 года назад

When you make the battery pack, what size nickel strip did you use and where do you get them?

@mygiguser 4 года назад

nytrhythm i don’t remember, but i got it from Amazon

@yashdobra9154 5 лет назад

Ok so now everything is done correctly just while charging the 5th led keeps on blinking after keeping it charging for a very long time also it keeps on blinking idk what to do pls help tell me when to stop my charging my

@mygiguser 5 лет назад

Yash Dobra measure the voltage of every single battery, are they all the same?

@yashdobra9154 5 лет назад

@@mygiguser so I checked the voltage of 2 batteries when I checked after charging was 3.87 and other two batteries was 3.72 this was it.

@yashdobra9154 5 лет назад

Bro there is one more problem after I connected everything and closed the JBL after playing it the bass sounds wierd some people say there is air leak but don't know from where the air is leaking or which part to seal pls help

@mygiguser 5 лет назад

Yash Dobra did you remove some of the battery compartment so that the new batteries fit 100%? If not, the door doesn’t close and then air leaks! There are not many spots where air could leak, but the battery door has to close all the way!

@yashdobra9154 5 лет назад

@@mygiguser ohhh crap! There's not much space there . That's why the door doesn't close fully , just some space is left it doesn't close dude is there no other way that I can seal it ?

@WCxColosus 5 лет назад

are there different ways of wiring the battery i say another video and the guys wired it differently

@mygiguser 5 лет назад

WCxColossus not that i know of, can you share a link?

@WCxColosus 5 лет назад

@@mygiguser thats the link

@mygiguser 5 лет назад

I am looking at this, and i connected mine the same way as the original battery pouches were connected, then i drew the schematic. Looking at the video link you sent, he is connecting the very same way, but it looks more complicated. The schematic is the same. That answers your question, there is only one way to connect the wires.

@mygiguser 5 лет назад

Look at this, i wired it the same way as the original Xtreme 2 batteries ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-Qut7biIdL-Q.html

@leonardooliveira70 3 года назад

Muito bom!!

@Leovixfull 5 лет назад

Hi. Great job. But is your battery diagram correct? It seems different from original bateries

@mygiguser 5 лет назад

Le o how is it different?

@mygiguser 5 лет назад

i look at it again, and it looks good

@Leovixfull 5 лет назад

@@mygiguser the green one, that negative, seems to me being in the positive and negative in the board. And once again, great video im going to do the same saturday with my jbl. Thanks

@TheShadyrainman 5 лет назад

Agreed, wiring is not the same as original batteries, couple other videos confirmed correct wiring, nit like this video

@BeautifulSafety 3 года назад

Why not make a wire with plug going outside, so you can connect and disconnect multiple batteries ? Make a fake battery pack inside to keep the sound the same

@skadi7654 2 года назад

because it is ugly

@linhang1264 5 лет назад

plss. can u make this for JBL chagre 2 + with 3.7V battery

@mygiguser 5 лет назад

Sorry they 18650 Li-ion don't fit in any Charge speaker.

@vishal0937 3 года назад

Will 2 batteries setup work.. if yes then how to connect bms?

@mygiguser 3 года назад

where do you put 2 batteries? there is not enough space

@ididnotgetabetterid 3 года назад

@@mygiguser i have onepack inside near the radiator. can install another pack in place of the original

@user-vy9ei7xm5x 3 года назад

Can you show with jbl Boombox battery ?

@mygiguser 3 года назад

it is the same concept basically all the same, no need to show this again

@miqueias_x 4 года назад

I did it on mine and it worked. Eu fiz no meu e funcionou.😁

@Ambr1942BR 4 года назад

Como fez para conseguir soldar na placa da bateria original ? Não aceita solda

@pedropaulodiasbulhosa3576 2 года назад

@@Ambr1942BR Compra uma plaquinha BMS 2s de até 10A es já feliz😊

@Christian.8.3.83 4 года назад

Weißt du ob die Xtreme 2 den gleichen Akku drin hat?

@mygiguser 4 года назад

Bobby Xtreme 1 hat Li-Po Pack und Xtreme 2 hat Li-Ion Pack

@ramontulfo4595 3 года назад

Good day sir..Can i mod it to a motorcycle battery?..does it safe?..thanks if there's any reply

@mygiguser 3 года назад

Ramon Tulfo maybe, but li-ion has more power

@ramontulfo4595 3 года назад

@@mygiguser thanks sir..i'm planning to do it😁..will it burn the board?..i think there's no thread here in yt anyone trying to do it on motorcycle battery..btw i'm filipino..hope you understand my english

@kyteyt2166 3 года назад

Every 18650 have different amphere,is that ok to use?

@mygiguser 3 года назад

yes why not?

@kyteyt2166 3 года назад

@@mygiguser it's confuses me that's why..i saw 40A 35A 30Aand i dont know whats the use of that..thanks for the answer by the way..😅now i just need to buy 2 18650 to fix my jbl.

@Juos10kustu 3 года назад

But there is hole in the speaker box now. Radiators needs a sealed box to be able to make bass

@mygiguser 3 года назад

fwe we use silicon

@Juos10kustu 3 года назад

mygiguser maybe some harder glue would be better but yeah

@samcbk 3 года назад

Lost the bass

@RayTv91 5 лет назад

hi.. is your diagram of battery is correct??

@mygiguser 5 лет назад

Oh yes, it still works fine. I know what I am doing.

@hallookdk 3 года назад

What is the white cable on the battery for?

@mygiguser 3 года назад

temperature sensor

@hallookdk 3 года назад

@@mygiguser Thanks sir!

@jasper232 5 лет назад

how many volts should be the battery of JBL XTREME?

@mygiguser 5 лет назад

7.2V and 8.4V max ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-PrKXumAvC8g.html

@jasper232 5 лет назад

@@mygiguser tnxs for the answer, so cannot put 14.8 volt right?

@jasper232 5 лет назад

@@mygiguser how many volt each battery that you use here in your video?

@mygiguser 5 лет назад

No you cannot, that is way to much voltage!

@jasper232 5 лет назад

@@mygiguser can i use 4 pcs of 3.7 volts each battery?

@VictorM02 5 лет назад

Can I use 4 18650 3.7V batteries each?

@mygiguser 5 лет назад

Vitor_ isn’t that what i used?

@carbonoxx 5 лет назад

@@mygiguser so using 4 battery is 14.8v! right

@floreaiulian8512 4 года назад

Depends on how you link them

@cherrycalcados2870 5 лет назад

top

@kuamhar1936 3 года назад

What is the model of JBL BMS module sir?

@mygiguser 3 года назад

i have no idea, i used the one from the old battery

@kuamhar1936 3 года назад

@@mygiguser I wanna know if its 1s, 2s or 3s..,

@kuamhar1936 3 года назад

@@mygiguser do you think that the bms of the charge3 is the same to extreme BMS?

@kuamhar1936 3 года назад

Can I do that to my JBL charge 3? What's that a combine of parallel and series connection?

@mygiguser 3 года назад

No, not enough space in the Charge3, and yes parallel and series!

@kuamhar1936 3 года назад

What is the voltage of that connection? I thought that jbl extreme is only about 3.7v

@kyteyt2166 3 года назад

How about direct current sir?

@mygiguser 3 года назад

The more the better. Base needs a lot of current.

@mygiguser 3 года назад

Look at this video, i used 3000mAh Samsung cells ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-lRUw4Im3o9g.html

@tarunconstantine9 3 года назад

The bms is dead what I do, HELP ME!!!

@mygiguser 3 года назад

buy a new battery from ebay

@tarunconstantine9 3 года назад

In india right now. God 😱

@ajaybiswas6490 4 года назад

Please make jbl flip 4 battery video

@J.boyz105 2 года назад

I love dis video I am an engineer I do dis all always but today was bad for me I Couldn't do for extreme 3 jbl can you me

@mygiguser 2 года назад

ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-P8x4QGRrXwA.html

@user-kh8vy5ko2d 4 года назад

Супер!

@erivancosta6302 4 года назад

Sou brasileiro tem como vc vender uma bateria dessa pra mim

@mygiguser 4 года назад

Desculpe, não. Existe Ebay no Brasil?

@gilcimarsouza2372 Год назад

Oi boa tarde como faz na boombox 1

@mygiguser Год назад

Bem, você tem que desmontar tudo. É mais fácil comprar uma bateria nova no Ebay e depois assistir ao meu vídeo aqui: ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-bS7SdO_4nWE.html

@gilcimarsouza2372 Год назад

Ela já dá desmontar

@gilcimarsouza2372 Год назад

Tem como vc falar como fazer

@paultram3664 5 лет назад

Wenn ich 4x18650ga nehme mit 3500mAh bei 3,6 Volt habe ich 7Ah bei 7,2V also ~50Ah. Ist das Problematisch denn der Lautsprecher maximal 40W im Netzbetriebt leisten kann? Beim Originalakku bleibt man ja bei 37Ah. Hoffe du kannst mir helfen. Danke und super Video

@paultram3664 5 лет назад

Das Netzteil hat 18v ist es also doch möglich dass der Lautsprecher mehr als 8,4v verträgt?

@mygiguser 5 лет назад

Der Strom wird vom battery management board an der Batterie geregelt und limitiert. Ich glaube nicht dass es dort zu Problemen kommt.