Jeep Cherokee: Transmission Mount Replacement - Automatic or Manual 4.0L ['87-'01 XJ]

Подписаться 10 тыс.

Просмотров 10 тыс.

50% 1

How to replace the transmission mount: Jeep Cherokee
4.0L Automatic: 1987 - 2001
4.0L Manual: 1989 - 2001
2.5L: ????
The AX-4, AX-5, A-904, 30RH, Peugeot BA10/5, and some overseas models likely use different transmission mounts than the one seen here.
The Mount I used (2000 - 2001 ONLY): www.amazon.com...
2 bolts: M10 x 1.5mm x 30mm
4 flange nuts: M8 x 1.25mm
How do I know these torque specs? Emanualonline has the factory service manual for the Cherokee at a discount here: shareasale.com...
Transmission Replacement: • Jeep Cherokee - Transm...

Опубликовано:

15 окт 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 50

@ML-uu7wy 4 месяца назад

“Ignore it and pretend it’s not a problem “ laughed my a55 off…. Thanks

@freetob1 4 месяца назад

SAME!!! LMAO CUT to a white Jeep driving away LOL

@spcekase 11 дней назад

For real😂 so me

@chipjumper 8 месяцев назад

Amazon. Inductive Heating Tool. Must have for anyone living in the rust belt. Gets those fasteners cherry red hot quickly. Zero broken bolts. You save hours of time. No fire hazard versus a torch. Priceless when I had to remove my fuel tank strap bolts from my WI native '00. Of course, all of the XJs here in CO don't even know what rust is...

@fishingjeepbc9519 11 месяцев назад

This is how video tutorials are supposed to be made. Great video

@MrSnowford 5 месяцев назад

You're the man! This was so helpful. Previous owner of my 99 decided to use the crossmember of a 00-01 for some reason, unbeknownst to me. So when I was trying to fit the 99 trans mount to it the entire trans/transfer case was all shifted to the drivers side. I thought I was losing my mind until I saw this and sure enough, the crossmember is not from a 99 so I need a 00-01 trans mount. You have greatly improved my mental state, thank you! LOL

@michael_fassbender Год назад

your xj videos breath new life into me. never stop

@rlt7409 Год назад

Happy to see you back to posting videos. For a young kid you do good work. I hope you pass through NYC one day. We'll look at my collection and see the city like a real NYer

@WAEMIDIV Год назад

The northeast has been unexplored for a long while. I'll get up there someday

@rheidtech Год назад

Doin a complete 2000 xj overhaul as we speak. Keep wrenchin fam👍🎩🍺

@insertcreativenamehere9704 Год назад

God the timing! I'm literally doing this today

@ryancarey1535 19 дней назад

So helpful thanks!

@rheidtech Год назад

Hey Waemid. Thanks. Use a 3/4 hole saw without a center bit and core out around the stuck bolt. Then weld a long tab to a 3/8 nut to be used as a washer and a anti rotation device. Slide it up into the frame hole you used to spray pbblast. Make it bigger with holesaw if need be. Add bolt and theres yur dinner.

@WAEMIDIV Год назад

"hole saw" "center bit" "weld a tab" bro you are speaking a language I do not understand lol

@JBenedict02 Год назад

*laughs in southern XJ*

@WAEMIDIV Год назад

sounds like I'm having a skill issue

@Eri-Lan Год назад

The process on the 2.5 is about the same only difference is with the 97+ models where there is a chance that you have the round motor/transmission mounts (AKA diesel mounts) that nobody makes. You will have to get new rubber inserts and press the old ones out. Replacement inserts are the same as KJ mounts but I am not sure on that.

@Wrencher_I6 Год назад

Both my xjs did the same thing I had won lol, Well one jeep had to tap both front crossmember bolt holes bigger.

@setheure8575 Год назад

I was planning on replacing this the same day I throw my new engine in later next month. As I was ordering it, I thought “man, I wish WAEMID had a video on this” . Quick question though, are you in my walls?

@WAEMIDIV Год назад

I am in the genie bottle at the back of your bookshelf, and have granted you 2 of your 3 wishes now, what will the final one be? Find out in the next episode after the break

@rheidtech Год назад

No. Raccoons are in your walls...

@aaronerickson8878 5 месяцев назад

Excellent video sir.

@dg98adams 8 месяцев назад

Cutting thru floor pan above the bolt and welding a nut is easier to fix & better than cutting unibody channel.

@d.sm.4146 Год назад

with a Warrio esq grinning nod, thinking to myself 'here we go' ;P

@kp7100 Месяц назад

Are the m8 bolts you used 30mm as well

@SamVeneman Год назад

what if I just send all the bolts with an air hammer? Wondering if that will snap them too.

@lingerseason Год назад

Which mount did you use? And did you get a slight knocking in first gear while the rubber broke in?

@WAEMIDIV Год назад

The one I used is linked in the description. I didn't notice any noises that weren't already there

@notsure3331 2 месяца назад

Quick question know this video is a year old hoping you're still there if you can move your drive shaft and transfer case up and down does that mean your rear end motor mount is shot cuz I can do that with one arm literally up and down over an inch

@WAEMIDIV 2 месяца назад

@notsure3331 yeahp I would say the transmission mount is fried

@kp7100 Месяц назад

Will this job work with only a jack supporting the transfer case? Or do I need one on the transmission?

@WAEMIDIV Месяц назад

@@kp7100 Just supporting the transfer case is fine

@joshualavigne4359 6 месяцев назад

Don’t want to bother you but I have a question for mj , a bad transmission mount cause vibrating when driving? And how to check. Thanks

@WAEMIDIV 6 месяцев назад

a bad transmission mount cannot cause vibration but it can amplify it from elsewhere. I would start by balancing the wheels

@joshualavigne4359 6 месяцев назад

@@WAEMIDIV ok. I will get them balanced. Thank you buddy

@KN1GHT2000 Год назад

are those grade 8 bolts? where you bought them from ?

@WAEMIDIV Год назад

ACE Hardware's bolt aisle

@Jayman0057 Год назад

👀👀👀 *WI footage*

@WAEMIDIV Год назад

yeah I just ripped it from the AW4 removal video because I'm lazy

@bunnybono1256 Год назад

i somehow drilled and tapped mine and used a starter bolt instead

@abdulbeany1894 Год назад

Hi what symptoms will a bad transmission mount cause 6 speed manual can it cause car vibration and clunking at idle thanks

@jorgegarage9593 Год назад

Bro I'm having trouble finding a transmission moun for a peugeot ba10/5 transmission mount

@jorgegarage9593 Год назад

I tried jegs and I guess they're on in back orders

@WAEMIDIV Год назад

@@jorgegarage9593 The BA10/5 mount is totally wack and completely different than the other ones, and I have no idea if they even still make them

@jorgegarage9593 Год назад

@@WAEMIDIV it's been almost 2 months looking for one might just have to do a transmission swap🤧

@WAEMIDIV Год назад

@@jorgegarage9593 They always say the 10/5 isn't worth spending any money on beyond gear oil

@Brolop19 Год назад

Goodsir Waemid, you should save yourself a shit ton of hastle and invest in some Milwaukee power tools.

@WAEMIDIV Год назад

a reason I don't use power tools is because when demonstrating to people how to do something, using them can be discouraging. Not everyone has power tools, and I like to show a given job is possible without them There are times when they're needed, and in those cases, I have a corded impact gun but it usually stays packed away for the simpler projects

@Brolop19 Год назад

@@WAEMIDIV Fair enough, I didn't think about that, when I watched your manual swap vid, and then did it myself. I thought you were kookoo for coco puffs not using power tools.😂😂 But you just put yourself thru the pain of doing everything manually so it doesn't discourage others that don't have power tools. I gotcha you crazy bastard.😂😂 Much respect for that!🫡