JUNKYARD TURBO SBC-WILL IT WORK? 

Instead of a shoot out, stick with the vortec. Put the iron heads back on and keep raising the boost. Prove what you can make on a budget, and how far you can push it..

Does this man ever sleep ? Thanks Richard for helping my addiction to horsepower in these times with all the content

Boost is like fertilizer , makes engines grow up big and strong!

I would love to see the “shoot out”. I have always wondered how big of a difference the sbc intake runner volume, heads, compression ratio, and oiling system would directly affect engine safety to power compared to the ls’s setup, Obviously if you ran the steam port setup with bigger rods on the ls you might be able to pull out more power than the sbc, but it would be awesome to see a price to power analysis shootout between old and newer tech!

100 % do the test please!.....one small note since when is 640 hp aomething to be embarrassed about...thats a hell of a street machine IMO..Bring that junk to my house!!! Love your vids!!!

Yes you should do it! Definitely! I'll be rooting for the 350 for no particular reason. Let's go 350!

Sounds like a big bang L31 series in the making!

Richard I’m a huge die hard SBC fan. But let’s face it, it’s 50s technology. Most don’t even know about the SB2.2 stuff. That would be a jaw dropping show for the LS guys.

Certainly, do the comparison. And I'm sure everyone would like to see you find the limit of the stock rods and pistons, as well...

Yes do a sbc vs LS turbobuild off. I have a 350 short block with 550hp topend, and twin50 mm dna motoring turbos, in my 1991 formula, built for 425hp, but I built it right, it may make quite a bit more. I haven’t tried it yet, but I will soon. I bought a L78 bbc that I will boost too in the future. I like to watch your videos and pick up on some of your techniques and build similar kind of motors. Thanks for your videos and all the knowledge you pack into these episodes. I’m Keith Houda from Chicago land south suburb, don’t work too hard and stay safe!

Yes do the shoot out! I’ve been trying to find videos on this! I currently have a 4bolt and an LS.

98' L31 Silverado. Changed the fuel injection to ramjet, comp cam and a d1 procharger made 380whp 440ftlbs. Took the procharger off and installed a turbo. At 12psi is made 430whp and almost 500ftlbs. Fun truck.

I'd love more small block tests! I think that there's kind of a notion that since the LS's are so popular (and for good reason), that now the SBC's are basically worthless and/or brittle... wrong! Boost 'em, Richard!

I ran a similar setup for a season, sbc twin 60mm with 20psi of boost. Made 777 torque and 625 HP to the wheels, had around 30 passes on the combo.

Given a proper tune - with absolutely NO detonation - the power levels possible on junkyard leftovers without breakage might amaze a whole lot of people!

Richard you are the Man.You go where no man dares to go.Thanks for all the hard work you do.

Yes, you should do this! I responded to someone on one of your other videos that I didnt think you could get 1000 hp out of a vortech with stock heads, and I doubted the short block would hold up. You responded you thought it could happen with no more than 19 psi. Id love to be proven wrong. Would be really cool to see it happen!

I'm inspired, I'm adding a turbo to my 5.7L s10. Never done it but time to learn.

LS vs 350 with stock heads would be great to see. Great work! Thanks.

Yes please do the shootout!

“Do it.” “Do it.”

Yes! Let's see the shootout! Thanks for all the videos and sharing the test results.

God damn it Richard...Now my wifes gonna kill me for ordering twin turbos 😂

I LOVE junkyards too..🥰🥰

Between this and Engine Masters, I think everything engine is covered.

2 summers ago i ran a small journal 327 with procomp heads and summit 1108 cam. Ran great until end of summer when i spun it to 7300 and was at 19lbs of boost with chinese gt45. Super budget build. Love your videos.

Great content Richard, I have a vortec 350 in my garage needing some attention and always thought a turbo set up would be too much, but since you showed us that it's not I may build it similar to what you had in the video. Thank you for sharing. A comparison video to the OG SBC would be enjoyable to watch. Take care.

Who in there right mind could thumbs down Richard? This guy provides all kinds of gear head gold. If you're here to learn knitting or gardening don't thumbs down Richard, just take your purse and leave.

Heck yeah. PLEASE DO. That’s what non LS guys have. We all want to switch over to a LS, but if I have an old school SBC, let’s see what she got

YES, because I have a 85 too corvette and I can’t make up my mind which way to go and videos are giving me a lot of information to think about. Thanks for the video’s, very informative and entertaining

I know the ls based platform is superior. I still have a few sbc blocks and parts that won’t die. I love the fact that we as hot roders can figure out how to make a combination work either way. Love the content!!!!

The salvage yard is my favorite place too. Lol I love browsing the aisles of cars and just looking at them from a crash and looking over the damage or just checking out everything up close

You should’ve done boost on stock heads that would be cool too see what we can get if we had all stock genll with boost and cam with stock heads❓⁉️

Thanks Richard! I commented a while back asking you to test one of these old mouse motors to settle a debate with a stubborn co-worker. I was surprised also! I'd love to see a shoot out and thanks again for taking the time.

Or do the same with a old school 327 versus the new school 5.3

I love the wreaking yard too. Potential everywhere. You really get a look into a society when you see what they discard.

SBC vs 5.3 LS shootout? YES PLEASE! 🙂

That torque curve is beautiful.

To join in with the resounding yes crowd, I second.

WOW...dude...you guys at Westech are killing ALL the myth's!

I'd be prone to want the LS just to know I've got a block I can't break (excluding rotating assembly failures that window it anyway) and more modern heads. A test to prove I'm blowing smoke up my own ass and an SBC can do more than I need would be awesome to see though, swap the cam and valve springs, gaptize them, throw on some decent head gaskets and head bolts, and let 'em go until one goes bang. One potentially neat twist: instead of turning up the power level until something blows up, maybe try setting an arbitrary power level both engines must meet (say 650HP at the crank for a comfortable 500+ at the tires) and cycle the engines between peak torque and peak horsepower until something explodes. Sort of a road-racing centric simulation to see if the low buck bangers have a chance in hell of surviving in a context like that.

Got super excited to see turbo'ed vortec 350 assuming was gonna start with total stock just add boost. Was sad when didn't happen that way first. Sorry Richard, but still love channel

Love it ! Definitely want to see what a Sbc can handle ! Love to see how they compare!

favorite episode yet!!! I have a pile of old sbc laying around from various projects and nothing to do with them.... until now! BOOOOOOOOOOOOST IT TILL IT BLOWS!

I think if they were both crank sensored, multi coil and fuel injected that sbc would surprise some folks on how well it lived with decent timing control and fuel control.

Yes please do the shoot out! I’m hoping to see more sbc videos! Cam shoot out in particular!! Thanks for the information!

In the beginning of the video I thought to myself : I'd like to see a sbc vs ls comparison. But I'd like to see a 350 sbc vs 5.7 ls.

Do it! Be a cool comparison.

I would love to see a big bang L31 (5.7 vortec), I have always thought the old sbc is a great platform and doesn't get enough love now with the ls and the lt motors. I would love to see how much a stock short block can take in comparison to the new generations of small blocks from Chevy. I would also like to the the shootout to see the difference between the generations.

Yes! Do the shootout!! Would love to see a similar test using a FIRST TPI set up.

yes do it!!! that will be very intresting since I have both a 350 vortec and an LS engine.

PLEASE DO THE SHOOTOUT GEN 1 sbc vs LS 5.3 this will stop guys from saying sbc are no longer popular and for the LS guys to have respect for the original small block Chevy. Awesome channel your in depth as much or even more than engine masters🦾

Hi Richard, big fan of yours. Perhaps you could share some suggestions on how to help the particular engine combo you test survive longer if a guy was going to build it himself. You must see the weak areas of each engine and could make valuable suggestions on how to avoid engine failures when building one at home. You could add these suggestions during your end of segment wrap ups. Thanks for your excellent shows, keep up the good work!

You need to build an engine for donut media. Build relationships with other you tubers with millions of sub and watch yours go way up!! Your on to something here with these awesome tests!!

do a 92-97 LT1 Vs the 5.3 might be a better match Especially since the Lt1 heads are aluminum and can take a good spring upgrade with no modifications If you dont wanna mess with the optispark just run a Carb Lt1 intake with distributor and blow thru carb

Your shoot out between the 5.7 Vortec and the 5.3 is very appealing to me!

The 350 VS LS shoot out isn't exactly fair since aluminum heads are better under boost and the iron SBC heads don't flow all that great. However If you slap on the CHEAPEST eBay SBC aluminum heads on the 350, it just got interesting.....lol

Yes I'd like to see the shoot out expanded to more junk yard motors!

I would also be interested to see how well they compare with a comparable rod and piston package. Apples and apples so to speak.

I'm wanting to do this with a ram jet intake setup with flipped s-10 headers .I've never seen one done like this I'd think it be hot hot hot ! Lol loved this thanks alot

Do it! I still love the SBC's!

I just rewatched this video... I can't wait for Rich to Drop the SBC vs LS because it seems Richard knows something we don't know but we been wanting to Know... "If that made any sense" so the Shoot out will be crazy to see how far a stock SBC can really go with boost and good tuning... And Shut a lot of dudes up who thought SBC can't do this or that

I’d like to see the SBC vs 5.3 LS shootout. Throw the Ford Windsor in there too all three with turbos

Hey Richard, thank you for ALL the hard work you put in to making these videos for us. I know (about) how much work you put in "behind the scenes" prepping these motors for some thrashing on the dyno and editing these videos. Thank you!!!

I have a question, is “boost” an accurate way to measure how much air is being forced into the intake? If I put 10cfm thru a drinking straw it will be at a high pressure, but the same 10cfm thru a fire hose will be at a lower pressure The actual amount of air will be the same but the pressure will be different, so is there a more accurate way to describe the amount of actual air being forced into the intake? Possibly cfm? That would be an accurate number, equal for the gen 1 vs LS comparison and eliminate the whole “ how much boost you running” debate , I realize that you discuss this but it’s still somewhat misleading to some people that think more boost is always good, more cfm is really what we are after

This information is just so Helpful... This set up will be in my next Suburban

Be nice to do a big bang test, see how far of boost it will go on the stock block..say like 19 psi of boost. Yes do the comparison, even though I know ls will out power the sbc, 15 degree heads for ls out perform,, compared to 23 degree .

Yes I would like to see which one does better and thank you for your time richard

Do a Vortec SBC vs an all iron 5.3 including heads so we’re talking super early 5.3 like 1999 or something, that way it’ll be fair

Old sbc had a beauty of a tq plateau

Let’s see Junk yard 350 vs junkyard 5.3 vs junkyard 454

YES! You should do the test. But I would use Aluminum Vortec heads in place of the cast heads for the 5.7L.

HELL YES DO A SHOOTOUT CHIEF PLEASSSEEEEEEEEEEEE!

I'm impressed! The old SBC did better than I expected. Keep up the good work. I'm looking forward to the 5.3 LS vs 5.7 SBC shootout.

Would definitely like to see more of this, dirt cheap build. Use those two gt45 do it all on the ultra cheap, then push it to the limit. Love the content you keep putting them up there I'll keep watchin em

Please do the comparison!! A 350 vortec Big Bang video would be awesome!!

Recent machinist channel site, made a valid statement on the 2 vs 4 bolt arguement. When was the last time you've seen a crank thrown from a block. While a 2 bolt, is stronger, due to it has more clamping force material.

Yes, Yes, Yes. ShoooooootOut thumbs up!!!!! Or just show us what the sbc can do on full tilt boost levels.

Yes yes yes ! As close as possible to the same build i think it will surprise a lot of ls guys

I would love to see that shoot out !! The only thing I would recommend on the 350 is that you use head studs and mls head gaskets. Then the old girl can take some serious boost !!!!! To keep it equal please put the same blow through carb on both test mules. Just for giggles can you put a small nitrous cam, solid lifter set up in the 350 so you can get some rpm out of it. Thanks Richard I love watching all these kind of comparisons.

Great test Very much needed real world data

Please please please do this with the Vortec heads. I saved this video as soon as you said you bought a vortec motor.... then my excitement was completely taken away with the other heads. Great video, now I'm hoping for the vortec comparison. 😃

Yes do the shootout. I’d also like to see what mods are needed to run the vortec heads and weather it’s cost effective or is a budget set of aluminum heads a better choice. I’m also curios to see how they would respond to no mods, junkyard fresh and just slap on the turbos, intake and carb.

Do the shootout!! Thanks for all the info Richard, love learning from your.videos!

Yes! Do a shoot out Stock Ls 5.3 and stock vortec 5.7..maybe ring gap, rod bolts and cam upgrade. I would love to see how long the sbc will hold up!

You should definitely do a big bang shootout between the cam springs and boost only LM7 and Vortec 350!

Shootout would be great would like to see exactly same camshafts exactly same cubes keep the content coming

That picture of the junk yard is certainly getting some mileage. LOL Thanks again for the content Richard. :thumbsup:

Hey Rich - when are you going to invent a tool to trim ring gap with the pistons still in the cylinder? You're the man for the job, we know you can do it; and save all of us cheap skates the effort of tearing down JY garbage just to fix some ring gap...

I would definitely love to see that shoot out. I’m trying to make a decision for my car right now with an LS or keep the small block so I’d like to see that shoot out.

Great test as usual , I’m a Chevy guy but would like to see 351 Windsor test as I had one in a van and liked it a lot .

Yes test those motors all the boost until they blow

Please do it. I have a 97 c1500 rcsb 2wd and want to make some more power but not sure what route to take. Great content keep it up!!

There is a ton of great info on boosting a stock sbc on the turbo forums or what used to be called turbo mustangs.

Definitely would love to see the shoot out! I know it's expensive but I would love to see a series of big bangs. Or even just see what these motors will hold with cams and boost if the heads aren't complete garbage. Ford, Chevy, Mopar, and who knows maybe even some Honda stuff.

I’d like to see a tunnel ram with 2 carbs and trim turbo. Do a hat and turbo on each carb and see what it does compared to other intakes.

Yes!! Yes!!! That will be an awesome comparison!!!!!

You made me love the thought of a sbc again.

Yes, also do one with an older sbc, some of them came with forged pistons and cranks. 010s have been legendary for years but alot of people nowadays claim they are a myth. Late model vortec will be interesting too.

Richard, Thousand of boaters would love to see what you could do with the mercrusier 350 mag engine. There is no videos on these MPI motors being upgraded. I think this would be an awesome addition, not to mention this should add 50 to 100k subs. The 5.7 motor has been put in millions of boats.