Kilns, using it correctly

Подписаться 297

Просмотров 3,4 тыс.

50% 1

There has been an explosion of people buying their own kilns and jumping in to the wonderful world of pottery. Yet they don't know how to run this giant toaster oven. Here are a few tips to help you get started using your new to you kiln. Just remember it is not set it and forget it.

Хобби

Опубликовано:

17 май 2022

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 15

@MsMrWildhorse Месяц назад

This is tremendously helpful.Thank you.

@Christianbaileyartist Месяц назад

Glad it was helpful!

@kandacew158 Месяц назад

I was so intimidated by the idea of running a kiln but this video has eased so much of my anxiety. This was the video I needed, thank you.

@Christianbaileyartist Месяц назад

You are welcome. I'm happy to answer any questions you may have about your kiln.

@MeSillyWoohoo 9 дней назад

Thank you so much. I am picking my kiln up on Thursday and I'm less freaked out now I will say my kiln sitter doesnt have a timer. So ive ordered self supporting cones, an analog pyrometer and am gonna be checking all this regularly

@vickimullins5027 Месяц назад

I am about to buy this model and being new to pottery felt intimidated, this video and your clear instructions have helped. Thank you

@Christianbaileyartist Месяц назад

You are welcome and if you have any questions please do not hesitate to ask.

@missyrnmissyrn7479 3 месяца назад

This is the best video I’ve ever seen on kilns! You freakin blew my mind with info in the first 5 minutes! I’m suppose to get a used kiln Friday. So grateful to have this video to refer back to! Thank you

@Christianbaileyartist 3 месяца назад

Glad it helped!

@Christianbaileyartist 3 месяца назад

Glad you found it helpful.

@meliviamutch3320 19 дней назад

Hi, I am a beginner and purchased an Evenheat 4320LT. To my luck,it had never been used so I’m enjoying the experience so far. I fired a bisque and plan to run a glaze fire to ^6 I’m glad you said to run it with a pyrometric bar of one cone higher. I would have just ran it with a ^6 pyrometric bar instead of the ^7. If I want to fire to a ^6, about how long should I set my kiln sitter timer for? I don’t want it to turn my kiln off prematurely. Thank you.

@Christianbaileyartist 18 дней назад

If this is the first time firing to cone 6 I would put self supporting cones of 5 and 6 in the kiln where you can see them through the peephole. Then set the timer for 8 hours and check the cones every half hour from hour 6 on until you see cone 6 bending then check every 15 minutes. If the timer is getting close to shutting off and the cone is not bent add another two hours to the timer and keep checking. You can always add more time to the timer while the kiln is running. If you have a hand held pyrometer place the thermocouple in a peephole and keep watch on the temperature. Use the cones inside to verify. Hope this helps.

@meliviamutch3320 17 дней назад

@@Christianbaileyartist thank you for your advice. I plan to try this out in a few days.

@urbangoth8455 8 месяцев назад

Hey there, thank you for such an informative video-it’s a bit difficult finding such detailed videos on this kiln. Looking at buying a similar model (DK 716-1) off a friend of a friend, but doing my due diligence first. What cone does this happen to fire to? 6, 8? Couldn’t quite catch it in the video. About how long are your bisque fires? I’ve been reading about 10 hours is expected for the Dover White (^5) clay I’m using. Thanks again for sharing your knowledge!

@Christianbaileyartist 7 месяцев назад

Sorry for the delayed response. This particular kiln is rated for cone 6 and it will reach it but struggles. It is much better for low fire. A cone 05 bisque firing on this kiln runs about 6-8 hours depending on how tightly I packed the kiln. It can also knock it out in 4 hours for when I'm doing an underglaze firing. What will determine the time a kiln takes to reach a temperature is size, power supply, age of the elements, thickness of the bricks and how tightly packed is the kiln.