Kromrey Converter testing and next steps to obtain higher output and desired characteristics. #science #electricalengineering #tesla #prototype #building #imagination
Great build so far. Remember you will not see the Rpm effects under shorted output unless you are running at 3000rpm or higher. You want to get a scope on the output to make sure it is generating the correct wave form aswell. I found whisker type brushes work best. Remember the gauge of the output wires can be small. Add another set of magnet stacks 180 from what you have there, after u rewind the coils with smaller gauge epoxy them. They will basically explode and unravel at 3000 rpm. Also you need a safety shield when running at those speeds. Great work so far!
The workmanship is good! I built a similar unit. 4 coils of 800 turns of 5 ohms. or just 20 ohms. At 1500 rpm, the output current is 0.2 amps 60 volts. while the motor consumes 12 volts 4 amps. the flywheel is a good solution, as an option put 3 pairs of magnets.
Having built MANY coils that will speed up the prime mover when shorted, I can tell you that EVERY coil has a frequency at which it will achieve what you are looking for. You have 3 choices to achieve the effect. 1. Increase the frequency of the coils passing the magnets by speeding up then motor. 2. Increase the length of the wire on your coil, which will increase its CAPACITANCE. or 3. Which is the simplest...... add capacitors in series with your coil. very, very small ones.
I did full research on this machine. I made a video about it how I improved it. Long story short, yes it does rev up under load I can confirm that. It has the same effect like the ordinary vacuum cleaner, when you clog the hose the motor revs up. But fact is, if you ad metal or another magnet to a magnet, the magnet becomes stronger. This means it takes more force to tear them appart again. And that's why this machine is useless. There's no way around this. It's physics. As you well know bigger planets have stronger gravity. If you put 2 magnets together, you have the same effect. It doesn't matter if it revs up under a load. I had a 12 phases kromrey generator. It took me 500 watts of energy just to turn it in idle. The more phases you add, the stronger the magnetic brake effect in idle becomes. Under full load the motor dropped to ~300 watts. Still 300% loss. It's not even a good generator, it's an energy waster. There's no overunity or perpetual motion.
there is overunity, its very easy to obtain in an open system... i will post my results when i get it producing excess power. if you try and measure the output without first putting it into lead acid batteries then you are missing the point.
It doesn't work. You're wasting your time. And open system by the way has got nothing to do with overunity. Overunity means perpetual motion. And most people don't know what this machine is. If it worked this would be a creator/god in detailed definition. You can't build a creator. A mortal builds a god?😂
What picked up from the Kromrey is, to use no neo magnets and a non magnetic shaft, so you've got those down. From Johns drawings you can see a trifilar coil, which wraps two bobbins, then the wires come together, I assume soldered and then are trifilar again on the two other bobbins. This could be an essential detail who knows. Also hé mentioned adding a hole in the iron core would aid the cooling effect, I can't make out from the video if you have that. Nice build!! So in my introduction video, 'The New Generator', I show a mini Kromrey that shows better performance when the iron pieces are longer, something to consider
Thank you for the comment, stay tuned, Im getting over my chronic pain and going to go hard on building in the coming months... I'm going to make Bedini proud! Thank you for the help, lets finalize this once and for all!
Good work, I try to make one but my coils was very homemade 😢... I have to improve my skills like an electrician...Can you charge the battery with the output like Bedini did in his videos?
Nice build, what is the cop of this generator?, mi bigger one has cop 0,65 from electric power in the motor to electric power into the load ,4 trifilair 0,27 ohm Coil in total1,1 ohm 32 v open at 1200 rpm en 12 v en about 3/5v lost in the brushes X5,5amp Ad 1500 rpm so it's speeds up under that load en takes off when shorted, in could never make it go over cop 1 😅
I build it just like bedini told us but I bed we don't have the right magnets for it 😅that always have used barium ferrite which ar illegal now , my theory about this extra energy if it possible at Al is greatly expanded by Paul brown, he discribed a few different methods to extract energy from radio isotopic material whit LCR circuits en that's look a awful lot like almost al the so called ( free energy machiene's en devices) on the internet ( don Smith, bedini, cpanatze, en so on )
ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-DIMqJdzmrP0.html. In this video he shows the secret of how Al the Inventors have fooled is for so long 😅at least that's how I feel after spending 16years build en replicating almost al of Them
@@MadscienceLPTECHoke there's a video where bedini is saying this a few times That it does matter 😅 En it works way better Whit laminated rotor peace's this is what makes the difference is cop 0,15 en 0,65
Once u get small gauge coils, are runny at +3000rpm safely, and have other set of magnets 180, you should be getting around 50-90V and feeling cold air coming from it
great! Thank you for the comment Joe, stay tuned... im going to put out my Bedini Motor Video in the next couple days, then work on the Kromrey in Nov / Dec... I will not stop until its working like we all know it should.... then charge multiple batteries and loads!
@@MadscienceLPTECH I have seen better overunity designs with coils outside instead of inside. Coil inside is not good, better to have as much of area affected by electromagnetic radiation as possible.
Have you tried to make a combination of bedini motor and a generator kromrey design to capture spikes from motor while producing energy and accelerating,,, been thinking for that but didnt make a prototyp
Your using 2 magnet spaced 180 degrees. Imagine if you did the same but with 6 magnets spaced every 60 degrees so that north is up at 0, 120, and 240 degrees and south is up at 60, 180, and 300 degrees. Assuming the rotor continues to spin at the same rpm, then the flux changes happen 3 times faster so you will get 3× more voltage. You can do any number of magnets 2, or 6, or 10, or 14, or 18. I'm sorry to ask again, are you actually commutating (switching current mechanically) or are they functioning like sliprings. And, is it 5v DC output, or 5v DC output after diode rectification? Have you thought about voltage multiplier circuit? Consider taking the output of the top coil, and feed it from the left to two diodes anti parallel with eachother, whete the top diode forward biased right and the bottom diode biased left. Then on the right side of both diodes connect a capacitor to each. And then connect the other side of both capacitors. And lastly, connect the output of the bottom coil to the center of the two coils. 5v DC from rectified AC has a 1.4v drop across two diodes. Meaning your probably getting 6.4v AC. And that is really 6.4 Volts(rms) root mean square, which is the average power equivalent to 6.4v pure continouse DC. AC sine wave forms have a peek voltage sqrt(2) times the rms voktage. That's 6.4 vrms × sqrt(2)= about 9.05v peek. Rounded to 9 volts peek and multiplied by 2 in a voltage doubler is 18 volts, and minus 1.4v for the two rectifying diodes voltage drop results in 16.6 volts stored across the two capacitors under no load.
For better and worse, comments with links get auto deleted so I can't post a link without it getting deleted. So maybe you can search for .... Voltage Doubler: What is it? (Circuit Diagram, Full-Wave & Half-Wave) by Electrical4U. I'm proposing the full wave version.
Sorry I miss spoke if I said communtator... slip rings Thank you for your comment, I'm going to add 2 stacks of magnets and see the difference.... I'll do that video next in February.... then I'll redo the shaft as it's crooked, and re wind the coils with 23 gauge wire.... then I also will try the shorting of the coils with a Reed switch... What do you think the voltage doubler would do to the radiant energy coming off??? Change it to conventional.... I'm under the impression I want to get the radiant energy into batteries asap then do the work / convert... I'm.making a fb page where we can all discuss these thing and finalize this machine to overunity once and for all.
@@MadscienceLPTECH I'm not sure what you mean by radiant energy here. Would you define it? Voltage doublers double the voltage under no and low load. Heavy load pulls the voltage down. If you upsize the capacitor's capacitance they will better sustain the voltage under heavier loads. But never will you get more energy out than was put in. Over unity is is typically a reference to energy out / all the energy in. Don't bother trying to get 1 or higher. It won't ever be possible. Sometimes over unity claims that are not outright hoaxes simply don't account for all the energy that goes in. Less commonly over unity may refer to power out / power in, but only by the very ignorant,because it requires including time for both, and the ignorant don't know enough to include it. But if they did include it, they would be back to energy out/ energy in. One can, at low power over a long time, store x amount of energy. And at a later time, they can dump x amount of energy at high power over a short time. Again the energy out / energy in will always at best be 1 in theory and less than 1 in practice.
@@MadscienceLPTECH four magnets won't work well. Remember with two magnets one has its north side up and the other at 180 degrees from the first magnet, has its south side point up. 2: N(0), S(180) good. 4: N(0), S(90),N(180),S(270) bad. 6: N(0), S(60), N(120), S(180), N(240), S(300) good. 8: ...... bad. 10: ...... good. 14, 18, 22........ good. For all interger values for z, 1 or greater..... Good arrangement = (4×z)-2
Kromrey, the Swiss man who patented this, found that the stator needed to be the ceramic magnets.The magnets weigh a lot too, so its a little easier to spin the coils at speed, without excessive vibration.
Well is nothing extraordinary in this generator, ciols magnetic , and you have to put power for making work...l don't see kinetic force in...we have to understand after master Nikola Tesla nothing is new, we just repit the same principal he made, is nice toy don't give me wrong... Anyway have a nice day.