Land Rover 4.6L Bosch Full Engine Rebuild (Discovery 2)

Подписаться 1,1 тыс.

Просмотров 18 тыс.

50% 1

In this video we rebuild a Land Rover Discovery 2 engine, specifically the 4.6L Bosch. We had to pull the engine due to a oil pump failure that destroyed all the bearings. We show all the steps in this video from the bottom end with pistons and bearings as well as top end with the heads and everything else. We also throw some custom bumpers on. Enjoy the video, if you have any questions or comments feel free to reach out! Vive Mas! More content is available on instagram via @xplormor_offroad and @errrry_outdoor

Авто/Мото

Опубликовано:

18 июл 2021

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 56

@JustRovingAround_Disco 5 месяцев назад

Fantastic work mate, and video is really well put together. I enjoyed. I sorta of have the same rebuild to do on 2 of my 3 Discos. It's gonna be fun.

@EverydayOutdoor 2 месяца назад

Thanks brother! Good luck on your rebuilds, fingers crossed it goes smoothly

@coreyking5135 10 месяцев назад

Thank you very much for your video, very clean work!

@EverydayOutdoor 2 месяца назад

Thank you brother!

@xtremeist9 3 года назад

That dang engine, I have heard many things about those 4.6's and not many of them have been good haha. Good video guys!

@EverydayOutdoor 3 года назад

They are known for some reliability issues thats for sure. Thanks for watching

@kennyh5083 3 месяца назад

I need to contact you! concerning information about Rover alum V8 engines and a possible rebuild from you guys. and I need some expertise advice too! Where are you located?@@EverydayOutdoor

@ericgarner8050 3 года назад

Awesome video Jon, impressive stuff you guys!

@EverydayOutdoor 3 года назад

Thanks so much man! I really appreciate it

@theredneckpirate5792 2 года назад

Big hello from Northern Ireland dude….. I have this very engine in my V8 rover 👌🏼 nice work

@EverydayOutdoor 2 года назад

Hey big hello right back at ya from the South Eastern US. Thank you for the kind words and watching!

@danielmebane6639 3 года назад

Another banger, did not realize you guys did land rovers also thought only toyota stuff. 10/10 great video!

@EverydayOutdoor 3 года назад

We do a little bit of everything! Thanks for watching brother

@kennyh5083 3 месяца назад

I need to contact you! concerning information about Rover alum V8 engines and a possible rebuild from you guys. and I need some expertise advice too! Where are you located?@@EverydayOutdoor

@EverydayOutdoor 2 месяца назад

@@kennyh5083 We are in NC what issues are you having? Ill try my best to help

@MrArmandoPhotography 9 месяцев назад

Great 👍 video bro. Great job! Wish would sprained all details So I can fix mine. Thx

@jonwelk2767 3 года назад

Fire video as always homies!

@EverydayOutdoor 3 года назад

Thanks fam!

@tbrinkley112 Год назад

You make it look soo easy. And Clean, lol.

@JustRovingAround_Disco 2 месяца назад

I just noticed there's an E38 in the background. So cool.. 740 or 750?

@keeganhunt8560 3 года назад

This is super sick bro, love this video!

@EverydayOutdoor 3 года назад

Thanks brother! I appreciate you watching

@davidholdren8315 2 года назад

03 v8s had a flaw with dowl pins .oil pump will fail again .check it out

@billykhunkhun1997 Год назад

Great video!!! I just pulled the engine out of my wife’s 2001 the bell housing bolts sucked and I had the heads off, how did you get them torqued with the engine fully built?!?!?!?

@EverydayOutdoor 3 года назад

Had to re-upload due to some technical issues

@TbsDltn 2 года назад

any stroker kits available for the rover 4.6 litre v8 in the states?

@user-cy1zr2oi6f Год назад

are engine cylinder sleeves replaced?

@landiesgentlemen3902 10 месяцев назад

Nice job other than this engine takes Dex-cool antifreeze.

@mackenziehaines1976 2 года назад

Is the audio just rough or is the engine sounding rough?

@EverydayOutdoor 2 года назад

It sounded a little rough in the beginning. We ended up pulling it back out and going through it again

@metalwaxdotcom 2 года назад

@@EverydayOutdoor great Video guys, I'm doing the same to my 04 4.6 same problems bearings burned up # 4 cam bearing walked into the lifter oil pump gear was broken. Im curious what made you pull the motor again? what did you find wrong? Thanks >

@Bulletstop75 2 года назад

NIce! Did you pin the liners?

@EverydayOutdoor 2 года назад

We did eventually haha

@Triumph67825 2 года назад

Where are you guys located? I have a 2004 Disco 2 and need the same thing done. Can you help a brotha out?

@adrianrivera9404 Год назад

Mine has the same problem yours had can you come and do what you did to mine in Grand Junction, CO.

@rupertomontalvo285 2 года назад

Great job guys. I have a 2000 discovery 2 looking to rebuilt the engine. I need guidance with this project. Was wondering do you have a contact number where you can reached ?

@guzulukonyi9316 6 месяцев назад

Can this engine work eith Defender 110 300 tdi

@victorarias2365 2 года назад

Uhh you got the unedited version. I need a reference and moral support lol

@EverydayOutdoor 2 года назад

its like 4 hours long but yeah I gotchu haha

@Triumph67825 2 года назад

@@EverydayOutdoor Would love it as well. Maybe I'll give it a shot with my 2004.

@shaynesmith3784 4 месяца назад

All that work to put the wrong coolant in?

@davelocock Год назад

How much you spend on parts ?

@tonye4176 2 года назад

Rtv sealant on the oil pans gaskets and valley pan 😬

@EverydayOutdoor 2 года назад

Gotta make sure shes sealed up. These things love to leak

@tonye4176 2 года назад

Newer Valley pan and later oil pan gaskets are specifically designed not to take rtv sealant.

@johnmay6442 2 года назад

Would you like to rebuild mine for me please lol it’s knocking like somebody is trying to bust out of the engine!

@EverydayOutdoor 2 года назад

Haha thats a common problem with these! Where you located?

@johnmay6442 2 года назад

@@EverydayOutdoor Somerset Ky but I’ll drive it out to you! Just got the M S transmission fixed by replacing the XYZ switch. Also went ahead and replaced the cam shaft sensor as well.

@landiesgentlemen3902 10 месяцев назад

It is likely a cylinder sleeve starting to slip up and down. You need a reman block. They pull the cylinder liners, and machine a groove around the top of the cylinder, then replace liners with a shoulder to keep the liners from dropping. It was a flaw in the original engine design.

@TwistedOwen 2 года назад

How much did the rebuild cost with machine work?

@EverydayOutdoor 2 года назад

Without double checking I believe it was around 650$ for the rebuild kit and the machine work and then an additional 350$ or so to get the other crank ready to go. So about 1K total plus all the little stuff like oil and beer haha.