LCRC Installs Hot Racing Wide Sway Bars onto a Traxxas Slash 2wd (Part Number TE311SLC)

Подписаться 1,1 тыс.

Просмотров 7 тыс.

50% 1

See everything we used here: lcrcraceway.com/collections/i...
Check out our new video of Kevin installing the Hot Racing TE311SLC Sway Bar Kit onto a Traxxas 2 Wheel Drive Slash with an LCG Chassis! The install takes less than 10 minutes, and we walk you through the entire process- No skipping ahead! Please like a subscribe!

Авто/Мото

Опубликовано:

18 янв 2022

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 21

@pickin4fund21 7 месяцев назад

Thanks, I am rebuilding my 2 wd slash to run on carpet. I will be adding these sway bars,

@ianchartrand4448 2 года назад

I like your way of installing the rear sway bar better than how the manufacturer intends. I think it will be more effective that way. Thanks for the tip!

@killerbeemike Год назад

great video. what i did for the rear is i cut the mounting bracket off so it was 2 blocks. that way when attached the mounts have the groove in them preventing the sway bar from popping out or binding.

@LCRCRaceway Год назад

Nice tip! Thanks for watching!

@rockncoop665 2 года назад

Very informative even if I don’t own the car

@LCRCRaceway 2 года назад

Thank you!

@GreenJeep1998 11 месяцев назад

Think one could take piano wire and make sway bars and at least mount the rears like that? I have a Bandit and Stampede that have the RPM extra long front arms and Slash/Stampede 4x4 rear arms and carriers and wouldn’t mind sway bars on both ends of both rigs for pavement use.

@gamercat7004 2 года назад

I can't finish my rear end I saw that you tighten it up but I don't see the set screws to the ends of the sway bar. Which I didn't see them in the pack.

@calebzimmerman7456 2 года назад

Hey Kevin! hope you're recovering from covid! Can't wait to come to your store when you reopen!

@LCRCRaceway 2 года назад

Thanks Caleb!

@RubbleRC 4 дня назад

Thanks for answer a question I WAS gonna ask and that is do they work with the LCG I bought a set for a 4x Traxxas brand but they don’t work so I put them on another with RPM oh man what a difference in driving so I’m setting up a 2wd for racing

@adamcasatelli3925 3 месяца назад

can you post a vid of how you mounted the bar under those 2 screws in the shock tower, I don't understand how the bar still can pivot after you tighten them down. I would think the screws would tighten on them and not allow them to rotate?? and if you leave the screws loose a little then your rear shock tower is not tightened all the way down..

@LCRCRaceway 3 месяца назад

Thanks for your question. I use the small aluminum spacers that come in the sway bar kit and put them under a set of shock pistons that would have come with your original slash. Then the bar can rotate behind the small aluminum spacer and the larger plastic piston holds it down. Meanwhile it can all be tighten up to hold down the shock tower properly. Hope this helps.

@tbnice9999 Год назад

Will this work on a 2wd rustler?

@rickysnow7437 2 года назад

why did you cut the rear bends off the sway bar? would help if you'd atleast give an explanation LOL, There made that way for a reason, from what I heard it's to keep the sway bar out in line with the Rear A-Arm ?? Thnx

@LCRCRaceway 2 года назад

Hey Ricky! We do not install them in the same way that HR suggests, which is why we trim them off to have them line up correctly with our installation technique.