Lexus Apple CarPlay & Android Auto Upgrade Installation Step by Step

Подписаться 2,9 тыс.

Просмотров 77 тыс.

50% 1

2017 Lexus RX350
Infotainment/Navigation Upgrade to CarPlay
Supply
1. CarPlay & Android Auto module + interface cables
In the video, I install a RoadTop CarPlay unit for Lexus:
ebay.us/HWRbuW
I have NO affiliation with them and hope to post a review video after some use.
For now, I've used CarPlay features but will test Android Auto too.
Tools
1. Panel removal tools (plastic)
2. Ratchet wrench
3. 10mm socket
4. Some towels
A. Radio Unit Removal
1. Open storage lid and remove central console panel/trims.
2. Remove (silver) trims around the radio.
3. Remove black trim where Start/Stop button is attached.
4. Disconnect Start/Stop connector.
5. Remove two 10mm bolts holding the radio:
one on the driver side
the other on the passenger side
6. Push down shift boot and remove shift knob.
7. Cover the shift stick with towels (to protect the radio unit later).
8. Remove the radio unit, and disconnect the connector at the top.
B. Screen Removal
1. Remove front and back trims around the screen.
2. Remove back cover of the screen.
3. Remove three 10mm bolts/nuts on the screen bracket.
4. Lay towels in the front.
5. Remove the screen and place it on the towels.
C. Connect CarPlay Unit Cables
1. Connect LVDS cables.
2. Connect CAN cables.
3. Connect USB / Video cables.
4. Connect RF Antenna cable.
5. Change Toggle Switch according to instructions.
D. Connect to Radio Unit Host
For each connector, chain them together this way:
1. Remove the original cable;
2. Plug it to the female cable to CarPlay;
3. Plug the carplay male to the host socket, where the original cable is removed.
Do this for the following cables/connectors:
1. Power or CAN cables.
2. Audio out cables.
E. Connect to Screen
1. Route LVDS cable from the back of the radio to screen.
2. Chain the LVDS connectors with the original cable/connector.
F. Test CarPlay
1. Reconnect Start/Stop and start the car.
2. Switch Audio Source to AUX.
3. Turn your phone's wifi, bluetooth, and connect to CarPlay.
4. Test the features.
G. Reassembly
1. Optional: Route the USB cable to glove box. The unit has wireless carplay so USB is not required.
2. Place the CarPlay unit in the back behind Radio. Arrange the cables and tuck them in the back.
3. You can stick the antenna to the side of the radio box.
4. Put the radio unit back, attach to the clips, 10mm bolts, and reattach the trims.
5. Reinstall the screen with 3x10mm bolt/nuts, back cover, front and back trims.
DONE.
Hope this video is informative.
Be safe, stay dirty. Enjoy the work!
God bless!

Опубликовано:

5 окт 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 371

@profsg Год назад

The RoadTop CarPlay unit in video: * Enter coupon code PROFESSOR to get $15 OFF: rebrand.ly/Professor/LexusCarplay * Or get it from eBay: ebay.us/hHsSQ6 Compare the prices and get the best deal!

@hauc8679 9 месяцев назад

"This listing was ended by the seller on Fri, Nov 10 at 4:32 AM because there was an error in the listing." . Can you send the link again? Thank you so much!

@profsg 9 месяцев назад

@@hauc8679 thanks for letting me know! I've updated the link and copied it here: ebay.us/HWRbuW

@wq7312 2 года назад

The best video I have ever watched. Try to teach you how to do it by yourself but not attract you to pay them to do it. Thank you! This is exactly what I need!

@profsg 2 года назад

Glad it was helpful! Appreciate the feedback.

@キドクラッチ-g5m 8 месяцев назад

I've been hesitat about buying this product. I watched your video and decided to buy it! It's a very easy-to-understand video, and I thought I might be able to do this. Thank you very much!

@profsg 8 месяцев назад

Glad it was helpful!

@wawadragaan 2 месяца назад

Just fit this on a 2018 Lexus RX 450hL Premium AWD w/ Mark Levinson. Thank you for the video Professor! Very easy to follow and made the installation a breeze. Only thing I would reconsider doing in retrospect is leaving the LVDS cable off and dropping the single end through the top of the dashboard to make it a bit easier to route to the Carplay unit. I attached mine to the unit first and didn't want to risk damaging it by pulling it out, so it took a good amount of wrangling to run up to where the display is (used a surgical mask as a rubber band to fish it up and through). Additionally for sound settings, first thing I did in the settings menu was turn off all EQ/Loudness adjustments to ensure there was no extra DSP happening to my audio. My carplay audio connector also came with a male 3.5mm aux and an audio ground cable that I left unconnected.

@profsg 2 месяца назад

Glad it was helpful! Thanks for sharing your tips. They make sense!

@profsg Год назад

An update after 15 months of use: The unit has been working well and I've not encountered the issue of overheating, which some people have reported about. However, here are a few things I may do differently than what I presented in the video-- 1) Do not attach the antenna to any metal, which I did wrong in the video. 2) Definitely keep the USB cable in the glove box, which provides charging and wired Carplay. 3) You may consider placing the Carplay unit in the glove box too in case you need to access it for troubleshooting. Not sure, though, how this may interplay with the potential overheating issue. I'd love to hear about how it worked out (or not) for you. Feel free to ask questions and/or share your experiences in the comments!

@MrAghotra Год назад

Thank you for this guide professor! I breezed through the install in my ‘17 RX350. I also added the USB cable through the glove box without having to disassemble the glove box.

@profsg Год назад

Excellent!

@Madhawa333 Год назад

Best video for Lexus rx450 on RU-vid I have seen. Thanks

@profsg Год назад

Glad you liked it!

@usuihasegawa 2 года назад

Great demonstration, I installed this unit in my IS a few months back. So far has been pretty great. Only problem when installing was in the manual it specified dip switch setting for my car, but in fact it was another setting that was compatible. So try out switch settings if ur unit does not show up. Another small problem is I find that there is a slight (about 1 second) audio delay, which is not a huge deal and does not affect turn by turn navigation. In terms of reliability, I’ve had the unit automatically restart in middle of drives. But it usually boots right back up. And sometimes it takes a few seconds for Bluetooth to connect. (Wired connection might be better) Otherwise this is a great aftermarket unit for the price.

@profsg 2 года назад

Glad to hear that! And thanks for sharing the experience and tips.

@EumgProductions Год назад

What toggle switch settings did you use? Do you remember?

@usuihasegawa Год назад

@@EumgProductions I used the ES with joystick one listed in the manual. That one worked for me.

@naseralshammari7745 2 года назад

Thank you so much. The video was very clear. I installed the CarPlay on my lexus IS.

@profsg 2 года назад

Great to hear!

@iambadescu Месяц назад

Very good tutorial. But... for the joystick to work properly, you need to connect a cable that you didn’t mention.

@profsg Месяц назад

Thanks! Unless the latest unit has different cables, I presented all cables necessary for the one installed in the video. There were CarPlay OS System Settings that I changed to make the joystick (remote lever) work more smoothly but I don't recall any specific cable for that purpose. Again, the product may have evolved/updated so feel free to share what specific cable necessary for your installation and perhaps the link to your latest purchase, if you don't mind sharing it.

@phillyb9499 Месяц назад

Thanks for this video. I’m about to install and this is very helpful. One question, it looks like you did not remove the battery terminal for this install. Do you recommend install without removing battery terminal?

@profsg Месяц назад

Glad you found it helpful! For this installation, we only disconnect and reconnect some of the existing connectors, and it's relatively safe while the battery is connected.

@JuanSanchez-jq6wu 2 года назад

I bought the same unit, I am getting ready to install it!

@profsg 9 месяцев назад

Thanks for watching! Hope your installation went well. Feel free to share your experience or ask any questions.

@groovymoon 2 месяца назад

Really great video. Will this work with 2016 RX350 with Mark Levinson Sound System?

@profsg 2 месяца назад

Glad you liked it! Based on the list of compatible models, this supports 2016 - 2019 RX350: rebrand.ly/Professor/LexusCarplay My module's audio connection is via AUX, which works fine. However, mine doesn't have the Mark Levinson sound system and I don't know whether it will affect the premium sound quality. You may ask the seller whether they have an upgraded sound input/connection for your model.

@amr3772 4 месяца назад

Hey man. Thank you so much for the great instruction. By far one of the best tutorials on RU-vid. I bought the same product from the website you mentioned. I have an issue and hope you can help me resolve it. When I switch to carplay, half of the screen shows the carplay and the other half still shows the original car menu which is blinking. Is there anyway to get this resolved and change it to full screen in carplay mode? Really appreciate any thoughts. The manufacturer has been unable to help me so far.

@profsg 4 месяца назад

Glad the video was helpful! I haven't encountered or heard about this issue, but suspect it might be a connection problem. However, it'd be useful to rule out other possibilities: 1) Have you tried both wired and wireless Carplay and got the same result? 2) Have you tried a different phone (perhaps an Android phone for Android Auto)? Does it also show a half screen? 3) When it's on the Carplay mode, and you shift to Reverse, does it change to full-screen reverse camera? Any glitch/blinking there? If you can access Roadtop/Carplay system settings with the half screen, there are Display/Screen related settings you can try. If your DIP settings are correct for your make/model/config and no issues with the connectors--some people have reported connection problems and you can use contact cleaner and reconnect to make sure--it might be a defective unit and/or requires software updates. As for Roadtop support, I know they are in China (a different time zone) so expect some delay in their response. The best is to shoot a video showing the problem and share that with them to figure out.

@amr3772 4 месяца назад

@@profsg Thanks much for taking the time to respond. I have disconnected the whole unit and connected it back with no luck. Still have same issue. I also messed with the CarPlay screen settings and it doesn’t give me the option to go full screen. And I know it’s not related to the phone or wireless either because the very first CarPlay logo that shows up when the system gets turned on is also on a split screen before I even try to connect my phone. I have been in touch with customer service but they just keep sending me different dial codes and nothing seems to resolve it so far. Thanks again for your support

@pincopallino1429 2 месяца назад

Professor, I purchased and mounted this control unit on a 2018 Lexus CT 200h, at the moment I have two problems: 1. the Touch remote does not work well on the Lexus system while I use it with Android Auto it works well 2. I can't hear the Android Auto audio and Google Maps. what can it be? I'm sure I followed the instructions perfectly but I have these problems. do you have some advice? Thank you

@profsg 2 месяца назад

Sure. Please double check DIP settings on your model/year as it's specific to your model/configuration per Roadtop user manual. For the two problems: 1) If the remote control doesn't work smoothly, there is an option in the carplay system setting regarding your remote control, e.g. touchpad, remote lever (joystick), etc. Select the correct one for your model. 2) As for the audio, make sure you are on AUX (or per your unit's instructions). Do test another app (e.g. with music/youtube/video) to see if you can hear any sound. There is an option on Google Maps to enable/disable voice guidance and sometimes it's disabled. Also, make sure you disconnect the original Lexus bluetooth connection on your phone AND turn off "use original/factory bluetooth" on the carplay's system settings. I discussed some of these settings in the video here: ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-yaBkp1MbwIU.htmlsi=tzC97I6sKdYLtgh-

@pincopallino1429 2 месяца назад

@@profsgI'll check as you told me. Thank you

@pincopallino1429 2 месяца назад

@@profsg Professor, I managed to activate the audio while browsing but by doing so I lose the audio from the USB stick! very important for my travels! Can't anything be done to fix it? I haven't solved the problem of the remote touch malfunctioning yet, I'll have to have time to reopen the whole car and redo other tests with the ECU settings in the DIP settings (the software settings don't solve the problem) for now I have to admit that I'm a a little disappointed with the performance of this product, also on my Lexus CT Google Maps or any other app is not displayed in full screen. I also saw the video you recommended but it doesn't solve the problems, I'm thinking of returning the product because if I can't solve it I don't see a real advantage in using this control unit for Android Auto, it would have been better to use the smartphone. (thank you again for your kind replies)

@profsg 2 месяца назад

If it's Android Auto, you can toggle the fullscreen mode by selecting/pressing the app icon (e.g. for Google Maps) on the left. Not sure if this will help but I have another review video more focused on the Android Auto: ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-WFQJfbzUvdw.html If you do reopen the radio to change DIP settings etc., I'd recommend you keep the unit inside your glove box and reroute the cables. Many people do that because it's much easier to access it whenever there is an issue. Best luck!

@pincopallino1429 2 месяца назад

@@profsgThank you

@breadicus66 2 года назад

Great video, very good instructions on how to install.

@profsg 2 года назад

Glad it was helpful!

@JustnZhao 9 дней назад

Hey I have just installed the exact same CarPlay unit from EBay today and was running amazing but after starting the car and restarting a few times I noticed the brightness started to be a bit too bright, have you encountered this problem would you happen to have a solution or if not what’s your best idea?

@profsg 9 дней назад

I haven't encountered this issue but you may look into the following two settings. 1) On the Carplay System Setting/Setup, under System, then Display, there are options to adjust Brightness, Saturation, Chromaticity, and Contrast. Double check and adjust them if necessary. 2) There are similar settings on your Lexus screen (original) menu. Hit MENU button, select Display at the top-right corner, then General, and you can adjust Brightness and Contrast there. Hope this helps.

@pincopallino1429 5 месяцев назад

One video for lexus CT 200h ( 2018/2020)? Tanks

@profsg 5 месяцев назад

If I can get hold of this model in the future. For now, you may want to check out this video from BeatSonic: ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE--9-qUbLeVBs.htmlsi=RCCs0Sa3DeGl4zSi My understanding is that these Carplay modules (e.g. Roadtop, BeatSonic) are similar, and you can look at these videos together for your preparation to install yours.

@pincopallino1429 5 месяцев назад

@@profsgtanks

@pincopallino1429 5 месяцев назад

@@profsgThank you. I saw the video you recommend but it's much more confusing than yours. I will subscribe to your channel immediately so if one of your videos arrives I prefer it because you know how to simplify them a lot. Thank you

@profsg 5 месяцев назад

Appreciate your support! Made my day!

@jatwood81 Год назад

Just installed for a customer. The horizontal lines are a bit misaligned and chopped if that makes sense. The screen has a glitchy feel to it. The customer service said it’s the toggle switches but I am absolutely sure we did 2,3, and 5.

@profsg Год назад

Not sure without seeing it. Is it chopped/cropped on the edges? Have you tried Left/Right/Top/Bottom scrap in the Carplay/Android Auto system settings? If DIPs are correct and none of these, it can be a defect.

@zongwang458 2 года назад

I installed it, great thanks for the video and suggestion

@profsg 2 года назад

No problem 👍

@warrenz202 2 года назад

IPHINE 13 CAN WORK?

@tonyzhao9108 Год назад

Great video! One thing I am having trouble with is displaying fan speed on the carplay/android auto screen. I have to always switch back to change the fan speed settings

@profsg Год назад

Thanks for the feedback! You are right. It doesn't show that status when you are in the Carplay mode, though the fan (physical) buttons continue to work on my RX.

@mureliz 2 года назад

Great video Professor, neat and clean during all the steps. Also like your voice, sounds like you speak with very slight German accent or German speaking manner. Anyway, just noticed one problem - according to the manufacturer you should not glue the RF/WIFI antenna to the metal surfaces, including the box itself, because this may cause some wireless connection signal issues. Instead you should glue it to the plastic surfaces, more closer to the driver, or where the phone usually lies. Another question - how different is the sound quality, compared to your oem bluetooth and aux? Also, when having a call inside the car, do you use oem BT phone or carplay phone via aux?

@profsg 2 года назад

Thanks for the kind words! On the antenna, you are right! I shouldn't have attached it to any metal because of potential interference. As for the sound quality, it is good overall. Radio talk show is all I listen to and I couldn't tell the difference. Once in the car, my phone is only connected to Carplay and I have disabled the OEM bluetooth. As long as the audio source is on Aux, I can make and receive calls etc. using wheel buttons or Siri.

@csrlee 2 года назад

@@profsg The wheel buttons don't work for me unless I am connected to bluetooth. Any idea?

@tylerjohnson9949 Год назад

@@csrlee I called this out with the mfr. They sent me a series of dip switch settings to try. I won't get a chance to do that until next Sunday.

@seol1500 7 месяцев назад

@@tylerjohnson9949 have you tried it out?

@gibbyng6594 10 месяцев назад

Will apple music and apple maps work instead of google maps?

@profsg 10 месяцев назад

Yes, they work! On iPhones they are easy to access because of Siri.

@gibbyng6594 10 месяцев назад

Buying it now! Thanks

@xrayos12 Год назад

just bought the roadtop CarPlay system thanks to your review. However, the manual says to use dip switches 2 and 3, or 2 and 4. I have a 2017 RX350 like yours with the joystick (Mark Levinson) with 12.3 inch screen. I see that your dip switches are 2,3, and 5. what's the difference? thanks

@profsg Год назад

I am not sure if the manual has been updated. The following appears to be the one I used: www.clublexus.com/forums/attachments/is-3rd-gen-2014-present/480572d1593099418-new-wireless-carplay-androidauto-for-oem-10-25-screen-user-manual-for-lexus-remote-touch-version.pdf I followed instructions under Section 3.5.1 on Page 7. That worked for my 2017 RX model. But if the module and manual have been updated, then I'd follow the new instructions. You can double check with the seller support.

@carsonHeinz 3 месяца назад

Hey I installed at worked out all the problems with the 360 camera and backup but whenever I turn the car to the original Lexus screen it just appears as a pink screen, do you have any tips?

@profsg 3 месяца назад

Is it completely pink or tinted pink? I suspect it's either a connection/wiring issue or due to Carplay software (firmware). Contact the seller support and see what they'd suggest.

@dodits1665 15 дней назад

@carsonHeinz what type of connection is your 360 connected to the screen? Is it LVDS or CVBS? I want to install 360 as well on my car. What is Lexus model is your car. Maybe you can help me. Thanks i

@bsaleem97 Год назад

Great video! Thinking about getting this unit, question 1- I have is would there be a way to route the audio out to a separate portable speaker? Either via bluetooth or aux cable? I have a small Anker Soundcore 2 speaker (I use on bluetooth with a spare phone for nav) the speaker fits perfectly in the empty compartment under the radio, would be nice to route the sound to that so I could still use the Media/Radio setting and still get navigation audio to the external speaker. Question 2- I've also seen units that replace the screeen with a 2k HD screen, any chance you have compared those with this one? Thank you

@profsg Год назад

Thanks for the feedback! On your first question, it is a very interesting idea and, technically speaking, I think it can work. I don't have the knowledge, however, about the type of connectors you need and how to route them. I'd suggest contact the seller to see if they have advice. As for units with a new HD screen, I don't have experience with those... I am quite satisfied with the original 12'' screen and feel no need for that upgrade. :)

@imagineaguy99 29 дней назад

I have a 2016 RX 350 with the rotating knob. Would this work with that?

@profsg 29 дней назад

I believe so! Wiring and/or DIP settings might be slightly different depending on the screen size and remote control type (e.g. knob vs. lever). But do contact the seller to confirm its compatibility with your model/year and that they send you correct cables for your configuration.

@imagineaguy99 29 дней назад

@@profsg Very good. Thanks!

@markfreeman3287 5 месяцев назад

Hi Professor, i have successfully installed roadtop carplay on my RX 350, it connects to the android auto wirelessly but im having hard time connecting it with wire. do i have to have bluetooth and wifi both connect to carplay for wire connection to work? it always connect to wireless android auto. please guide?

@profsg 5 месяцев назад

You don't need to have bluetooth/wifi for wired Carplay or Android Auto. Do disable bluetooth if you don't want that to connect. And when you plugin the USB cable, there is an option on your Android phone to enable USB Data Transfer/Android Auto. Enable that, and you should be able to go through the steps to set up/connect wired Android Auto. Best luck!

@nunosc3225 6 месяцев назад

Good morning. Great video and explanation btw. I was wondering if there is any diference between carplay for touch version and for knob. Or if it is just about toggle switch setup. Thak you in advance!!

@profsg 6 месяцев назад

Glad you liked it! According to it's manual, which I repost here, the pointing device and screen size etc as part of your model configuration determine the wiring and DIP settings: www.clublexus.com/forums/attachments/is-3rd-gen-2014-present/480572d1593099418-new-wireless-carplay-androidauto-for-oem-10-25-screen-user-manual-for-lexus-remote-touch-version.pdf Please do double check with the seller regarding your model year to get the correct cables in the first place. Hope this helps.

@nunosc3225 6 месяцев назад

@@profsg Thank you for everything. Clearer now!! Best wishes!!

@JMason35-z3e 5 месяцев назад

Professor, great video. How long does this install take? Thank you.

@profsg 5 месяцев назад

Glad you liked it! It took me several (interrupted) hours then, as I was trying to follow instructions and figure things out when details were missing. Dropped one bolt and couldn't get it out. Hopefully this tutorial helps save people time. If I do it again, it will probably take an hour now. It'd be good, though, to plan this for a morning or afternoon job during weekend when the car is not needed.

@mrsalviboy94 3 месяца назад

Where are you located? I’d like to upgrade but don’t want to risk making a mistake

@profsg 3 месяца назад

Thanks for the trust! Sorry we don't have an affiliated shop but are happy to help if you've got questions.

@zongwang458 2 года назад

Thanks for the video really useful, 2 questions appreciate if you can answer, does this work for RX450h? And when using Waze, put the address on iPhone or using joystick choose letters on the screen ? Many thanks

@profsg 2 года назад

Sure. To your questions-- 1) On the product eBay page, it says it supports RX in general. I suspect it does but don't really know. You may contact the seller to confirm. 2) I don't use Waze but, with Maps, you can use your phone to enter an address and start navigation. So yes, you use the phone to type. Or even better, activate Siri with a long press on the joystick and ask it to help.

@hermsky 2 года назад

Hello Professor, can you do a video/review on how Android Auto works with the unit? Thanks!

@profsg 2 года назад

Yes. That's the plan. :)

@七舅姥爷-v8q 10 месяцев назад

How is the sound quality for this CarPlay module compared to OEM

@profsg 10 месяцев назад

Good enough for me but mine is mostly used for listening to talkshow radio, etc. It probably doesn't make a big difference in this case. I do know some folks aren't impressed with the sound quality, especially when there is noticeable engine noise. I remember NOT to connect one of the ground wires for audio to reduce engine noise.

@キドクラッチ-g5m 8 месяцев назад

Hello Professor. In the video, the RF antenna was connected to the CarPlay unit, but was it also connected to the car side? In case of my unit, a Wifi cable was included instead of an RF antenna cable, so does it need to be connected to the car side?

@profsg 8 месяцев назад

The antenna is connected to the Carplay unit so it can transmit wireless signals. However, it doesn't need to connect to the car itself. You can attach (glue) it to something plastic--NOT metal which may interfere and I did this wrong in the video--on the radio unit so it stays in place. I assume the Wifi cable you have serves the same purpose and should be connected to the carplay module only.

@キドクラッチ-g5m 8 месяцев назад

Thank you very much for your detailed explanation. The antenna cable does not need to be connected to the car side, but it is important to fix it to the resin part so that it does not touch metal. I understood it very well.

@Spo8 Год назад

Thanks for the video! I'm curious which actions you have to perform every time you turn the car on. Do you need to change the audio input to Aux every time you turn the car on? Or is the only thing you have to do when you turn the car on to hold the Menu button down? Have you noticed any lag in the interface or audio?

@profsg Год назад

Sure! It automatically goes back to CarPlay and aux if it was in that mode when you turned off the car the last time. No need to switch to aux or long press menu in this case. I didn’t notice any lag in audio, though I believe there are audio/mic delay options in the system/OS settings that may affect this.

@Spo8 Год назад

@@profsg Thank you! Appreciate the answer!

@kamalzee9020 2 года назад

Hey so I install mine on a 2017 rx350 no navi everything works but I’m having issues with Bluetooth no one can hear me when they call can you help?

@profsg 2 года назад

Did you disconnect existing bluetooth connection to the original Lexus system? It may help to remove/forget that connection while you test Carplay. Best to contact the seller support and let us know what you find out.

@Ron-dr6iw 8 месяцев назад

Hi Professor, I purchased one of the CarPlay units but I have an issue with it. When I turn on the vehicle turning indicator the CarPlay unit shuts down and my screen goes blank until I turn off the indicator. Do you know of any solutions to fix this?

@Ron-dr6iw 8 месяцев назад

I solve it, it was a setting in the CarPlay unit needed to be changed.

@profsg 8 месяцев назад

Great! Thanks for sharing!

@rtrades1963 6 месяцев назад

@@Ron-dr6iw mind sharing the setting?

@happy24hugo Год назад

Thanks for the demo professor. Followed the instructions to installed this into my 17 RX. Wondering have you encountered the situation when use the joystick but both the original interface and the CarPlay got controlled?

@profsg Год назад

You are welcome! I didn't encountered this but heard about it multiple times. It's probably a defect product and you can get in touch with the seller for a return/replacement.

@NZphillugnutin6864 3 месяца назад

Good day Professor! Any idea if CarlinKit 5.0 2air works on our Lexus RX 2017?

@profsg 3 месяца назад

Good morning! If this is what you meant, amzn.to/4cCfumH for CarlinKit 5.0 Wireless CarPlay/Android Auto Adapter USB for Factory Wired CarPlay Cars, then the answer is no. As the name suggests, it's for cars already with factory WIRED CarPlay or Android Auto and the Carlink kit will add WIRELESS connectivity to the existing functionality. On 2017 Lexus RX350 shown in the video, it doesn't come with any factory CarPlay module (wired or wireless) and one must follow the installation process in the video to add an aftermarket module to the radio unit. Lexus only introduced CarPlay in later years, which is a typical Toyota strategy to "innovate" slowly.

@profsg 3 месяца назад

BTW. The RoadTop module I installed in the video comes with both wired (USB) and wireless CarPlay AND Android Auto.

@rainaremytears 3 месяца назад

Hello Professor, do you experience any buzzing when putting it on AUX after installation?

@profsg 3 месяца назад

No, I don't experience any noise myself. However, if it's engine noise, it's likely due to a ground (GRN/D) wire and you can simply disconnect it to see if that mitigates the issue. Keep us posted.

@zongwang458 2 года назад

Sorry one more question about the usb cable, how you through it into the passager side? Need to fully remove passager storage box ? Thanks

@profsg 2 года назад

I removed the glove box to route the cable. You don't have to do that, but it does give you better access and visibility and the glove box is not difficult to remove.

@Chosen0ne 11 месяцев назад

How is the unit doing so far? Have you experienced any bugs with this unit yet? Any overheating issues?

@profsg 11 месяцев назад

No major issue. No overheating. Check out my 18-month review: ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-WFQJfbzUvdw.html

@leonidmihalcu4898 Год назад

Hi Professor, Thank you for this useful video. I live in UK and I can see that this device is not delivered to UK. Do you have any other link to help purchasing it? Many thanks in advance

@profsg Год назад

I am not affiliated so don't know for sure. But for the product I purchased, here is the company's site: roadtop.com/ Looks like they have stocks in UK as well.

@SamNhean 2 года назад

I found it's very hard to use the joystick controller on this interface for the Lexus RX. Are you experiencing the same problem?

@profsg 2 года назад

Yes, the joystick is a bit challenging to use. That said, make sure you do the following to mitigate the issues: 1. Under CarPlay module system menu, there is an option for Touchpad/Remote Lever. Change it to remote lever. 2. When using the lever/joystick, move it horizontally to scroll. Hope this helps.

@profsg 2 года назад

One more suggestion- Whenever possible, use Siri. You can long press the joystick or enter button to activate Siri.

@SamNhean 2 года назад

Thank you! I was hoping for functionally close to the original. I already did what you asked and used the "remote" option but was hoping maybe I had a wrong dip switch setting. Thanks for the tip on long pressing the joystick!

@SonNguyen-ix5yg Год назад

Hi, How it works in the winter? Is there any overheating issue? So far, do you have any major inconvenience with that?

@profsg Год назад

I have no problem with overheating but heard some people have that problem. It did occasionally disconnect. No other major issues so far.

@rmoradi 7 месяцев назад

Hi I was wondering if there is solution to the screen flickering at bottom on apple carplay without restarting the carplay?

@profsg 7 месяцев назад

I haven't encountered such an issue but it can be due to connections: 1) Have you tried wireless vs. wired/USB connections, and see if it makes a difference? 2) Not sure if this is related to your problem, but here is a post about cleaning the LVDS connectors to solve a flickering problem: www.clublexus.com/forums/is-3rd-gen-2014-present/995138-flickering-on-roadtop-modules.html

@SOCAL_SHORTS_FACTORY 2 года назад

How bad is it to using the joystick for navigating around the Carplay? Do you mind sharing more info?

@profsg 2 года назад

I'd say it works fine, but no comparison to a touch screen. It scrolls horizontally first. For example, on the home/Apps screen, when you swipe the joystick to the right, it goes from one app to another in the first row, then the second row, and after that, the next screen. I arrange my apps in such an order so I can get to the most used one first, e.g. maps among the first apps on the first screen. When driving, I rarely use the joystick. It is easier to use the other buttons: on wheel buttons to take/reject calls, map button to switch between full map/split screen/home screen, etc. Most of the time, I long press the Joystick or the Enter button to activate Siri, and ask it to find places, make calls, read messages, etc. Hope to post a review with instructions on settings and use.

@profsg 2 года назад

Wanted to add a note-- I think you can use the joystick to go up/down on the home screen. But I am now so used to going left/right because, even on the vertical list such as contacts, you swipe left/right to go up/down. I believe there is a configuration setting to change this behavior but I am used to it now.

@SOCAL_SHORTS_FACTORY 2 года назад

@@profsg thanks for very through reply! I placed an order of the same unit for my RX. I hope it’s really not that bad as some people say it is.

@nicosstav42 Год назад

Hi professor, loved your video, I seem to have exactly the same model unit and car as you with the joystick control and 12” screen, are you able to share the instruction manual you have? I didn’t get much documentation and I’m struggling with the dip switch and some of the wiring isn’t clear, there are some single can wires like green and grey up near the screen which you can either connect or disconnect and just wanted to see if you might be able to help with what you did thank you!

@profsg Год назад

For the Roadtop unit I purchased, you can find PDFs instructions online. But it’s best to contact your seller’s support line if you don’t have the manual. They should provide one and know the best about the module and wiring.

@AlexK1372 Год назад

@@profsg BTW the manual is here: drive.google.com/file/d/1gjbSU_mpS_-VY8UcDeODnJ4bAIK00Fbf/view?usp=sharing

@profsg Год назад

@@AlexK1372 Thanks for posting it!

@Flexcobar503 Год назад

Professor... much appreciated! I had two issues that I am hoping you can help me with. My CarPlay often times doesn't play music for a while and then it starts playing. Also I cant seem to receive and hear calls either. Have you encountered this issue before? Thank you for your help in advance.

@profsg Год назад

Sure! Here is what I'd suggest to troubleshoot: 1) Make sure your audio is on AUX and the volume is turned on. 2) Disable the connection with the original Lexus Bluetooth connection so there is no interference. 3) Connect your phone with USB only to see if it's related to the wireless connection. 4) Try another iPhone with the USB connection. 5) If music doesn't play consistently, how about any other apps that output audio? For example, can you hear from Google Maps' voice guidance? There are also options in the Carplay OS systems settings related to audio or mic pre-configs. If none of these works, the unit might be defective.

@nikman4k243 11 месяцев назад

But is unable to connect Airplay even when it’s connected to same wifi any tips plz

@profsg 11 месяцев назад

You will need to turn on Wifi and connect to Carplay via the bluetooth. Does it not connect at all? Does it show Carplay after you long press Menu (for 3 seconds)? If it's not responsive to wireless connection, it may be a good idea to try the USB cable/connection. If even that doesn't work, then your unit might be defective.

@superjzh 11 месяцев назад

Thanks so much for the video ❤

@profsg 11 месяцев назад

You are welcome! Glad you liked it!

@ramirezmexican Год назад

I have a question i installed everything like you show but i dont have any audio everything else works fine

@profsg Год назад

You may try the USB cable, make sure it’s on aux, and double check the Audio / Volume setting in your CarPlay module’s system strings. Good luck!

@warrenz202 2 года назад

The best video . I have a question iPhone 12 13 14 can work ?

@profsg 2 года назад

Thank you! We have iPhones 6, 8 (regular use), and 13 (regular use), and they all work nicely. So I trust iPhone 14 and future versions will continue to work well with the unit.

@slac6972 Год назад

Hi prof, I changed the battery and the navigation system has some problem that it’s totally down but still lighting. If i unplug the head unit and reconnect again, is it work? Or should I change to the new head unit (which has the car play)? Thank you

@profsg Год назад

Hard to say without a look. Assume your new battery is all good in spec, it could be CarPlay wiring and/or battery grounding, or something shorted. These are places I’d check.

@kenhuynh3623 2 года назад

hi, i have a RX L 2018. and im thinking to order a carplay interface to set up for my car. So how is your carplay interface. i know you have been using for awhile , is there any issuses at all ? thanks

@khansnyc 2 года назад

RX L 2019 and have the same question!!!

@kenhuynh3623 2 года назад

@@khansnyc would you like to upgrade the start stop engine button ?

@profsg 2 года назад

The experience has been rather positive, as I haven't had a major issue since the installation. My plan is to make a review video and share some tips on mitigating some of the minor issues. Stay tuned!

@rmoradi 10 месяцев назад

Thanks!

@profsg 10 месяцев назад

Appreciate it! Glad it was helpful!

@johnhettman7056 Год назад

Absolute crash and burn when installed in my Lexus RX. The joystick would respond on and off with delay as well. Initiated Siri to navigate and my factory navigation responded not maps. On first drive iHeart was fine for about 5 minutes and all of the sudden CarPlay shut down and screen went blank! This was my second purchase of aftermarket CarPlay (Beat-Sonic) being the first and Roadtop the last.

@profsg Год назад

Sorry to hear about this. Looks like they are both defective. Did you contact the seller for support and replacement/refund? It must be very disappointing to do this twice and not get the result.

@profsg Год назад

Or could it be something related to settings, DIPs, etc on your model?

@johnhettman7056 Год назад

@@profsg I’ve got a 2019 so the setup should be the same as your 2017 correct? Also did you connect the audio ground to the main ground? Did not see that in your video.

@profsg Год назад

@@johnhettman7056 No, I didn't connect the audio ground wire, which, in several reported cases, seem to introduce engine noise to the audio.

@AlexK1372 Год назад

Hi Professor, I just bought and installed same unit. Question though... When I activate turn signal the screen goes back to Lexus screen :( do you have any idea how to fix it? '17 RX

@AlexK1372 Год назад

Got reply from the seller... "Match 360 display" must be off

@profsg Год назад

I didn't encountered this issue but thank you for sharing the information!

@ZiYang-fh5ub Год назад

Thanks for sharing the installation. The Lexus RX350 doesn't support Chinese lyrics when playing songs. Does the Carplay support Chinese?

@profsg Год назад

This depends on the iPhone (or Android) and apps that you have. The Carplay is technically an extension of your phone's operating systems, so whatever is supported by your phone will be projected to the carplay screen. I haven't tested this but theoretically different languages included Chinese should be supported. Keep us posted if it works out for your settings.

@profsg Год назад

And if you have an app that shows Chinese lyrics and supports the Carplay mode--not all apps can work in the carplay mode though--then it should be able to do that on the carplay screen. But there can be safety concerns for the app to turn off lyrics in the driving/carplay mode.

@ZiYang-fh5ub Год назад

@@profsg got it. I just ordered from EBay. Once I installed it, I will try it out. Thank you.

@monkey8obo Год назад

Hi professor, how to utilize the HDMI port on the module?

@profsg Год назад

I've heard people used it successfully, though I haven't tried it yet. Be cautious though this should be a feature you use when the car is parked. :) Based on what I have read-- 1) The unit has HDMI IN, which should accept streams from any device with an HDMI output, e.g. FireStick, Google TV. 2) On the Carplay System/OS, there is an HDMI app, see the screenshot here: ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-I8eCbVxB6e0.html which I assume will play whatever streams from its HDMI In. FYI. Here is a comment/suggestion about connecting phone wifi to FireStick to HDMI: ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-yaBkp1MbwIU.html&lc=Ugw2rrsodeV_bvRNCvR4AaABAg Hope this helps. Be safe!

@NZphillugnutin6864 Год назад

very nice video! Do you have sound issue coming out from AUX? I have humming,hissing or static sound from AUX it seems that something is grounded. But using the sound from bluetooth is fine.

@profsg Год назад

Thanks for the feedback! I don't have this issue, but some people reported similar problems with a solution. You can check out related comments under this review video: ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-yaBkp1MbwIU.html&lc=Ugww909ey7i0zTRH_AN4AaABAg The culprit seems to be with the Audio-GRN (ground) wiring. The solution is to NOT ground that wire to eliminate engine noise.

@NZphillugnutin6864 Год назад

@@profsg yes actually I should have said engine noise that is exactly the annoying sound not hummimg or static. which plug can I find the green wire? there is a green wire from the OEM plug not from the harness plug. is that the plug next to the OEM big main large plug?

@profsg Год назад

@@NZphillugnutin6864 I believe it should be part of your AUDIO (or USB) cable cluster. It is the wire labeled as Ground or GRND or GRN or Audio-GRND (not "green":). This wire is normally connected to a metal on the car--which is in the end connected/grounded to engine--but in this case should be disconnected.

@tylerjohnson9949 Год назад

Did your next/last track buttons on the steering wheel work with the unit or are they non functional?

@profsg Год назад

Mine are not functional for now. But check out the following comments: ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-I8eCbVxB6e0.html&lc=Ugx68Hh--07HMoDuDTN4AaABAg.9iTsmyBw1Ie9iV_EhNvmqQ Looks like it can work but you may need to play with a few settings. Let us know if it works out. I will give it a try too.

@h.billieli1563 2 года назад

Hi, Prof. Can you provide a long term reliability update? Does it disconnect in the middle of the driving? Or does the system freeze often? I am concerned about the aftermarket electronics reliability. Anyway, it’s a very informative video. Thanks 🙏

@profsg 2 года назад

Thanks for asking! This review video is in the making and to be released soon. To your question-- No. This hasn't happened to me. I have seen reports of overheating but my Carplay has been working without any major issue, even on long trips. Perhaps this isn't an issue in the Spring/Summer when we have AC in the car (and Carplay is on the AC passage) but I will monitor the situation in the upcoming Fall/Winter when I turn on heating. :)

@ItsPaulby Год назад

@@profsghow has it been? Thanks

@profsg Год назад

@@ItsPaulby Thanks for asking! The unit is still running strong after more than a year, all seasons. Surprisingly, I've yet to encounter any overheating issues some have reported about. I am very satisfied with the purchase as I discussed in the 4-month review: ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-yaBkp1MbwIU.html BTW. I started to use a new Android phone and hope to provide a review regarding Android Auto experiences with the same installation.

@oohlio Год назад

Awesome video. Does this unit show any information on the heads up display or on the multifunction display in the instrument cluster?

@profsg Год назад

Thanks for the feedback! No, it doesn't show/affect anything in the instrument cluster, e.g. on the small display. It only affects the big infotainment screen, except the on-wheel phone buttons now connect to the CarPlay module. I see this as a benefit not to interfere with existing features such as pre-collision warning and backup rear view in reverse. Less is more. :)

@ben97785 2 года назад

Hi Professor, just a quick question regarding to the audio quality of music from Carplay. I have a Lexus 450h 2018 with Mark Levinson sound system. I usually play music via Bluetooth on the factory system. I know that for carplay to work, we need to connect both wifi and Bluetooth to the carplay module Will the audio quality be distorted when play through the carplay compare to the factory system? Thank you.

@profsg 2 года назад

I mostly listen to talk show radio and, as far as I can tell, the sound quality via AUX is great! I am not sure how this may affect the Mark Levinson system. The alternative is to switch media source to your preference (e.g. Bluetooth or USB) and listen to music from there, though without voice guidance from Maps.

@janetlee6978 2 года назад

It’s very good . Would you please let me know where to buy and the brand and name of the new facility. Thanks

@profsg 2 года назад

Here is the one (branded as RoadTop) I bought on eBay for the RX model in this video : www.ebay.com/itm/384400476740 There are other brands/sources and they appear to be similar. I bought this one because it was less expensive and I came across some feedback/reviews on Lexus forums. There are some settings you may need to adjust for your car model/configuration/control, e.g. to improve joystick/lever usability and to reduce call echo. It works out nicely for me so far, especially with Maps, Siri, and managing calls and messages on the road.

@Ericisme21 Год назад

Installed this on my Rx350 and can't get the steering wheel controls to work to skip and replay songs. May I know if you got it working with yours?

@paultownsend2664 Год назад

You might hav to set Wheel key swap to “No swap” in CarPlay Home/settings

@Ericisme21 Год назад

@@paultownsend2664 I'll try this! Keep you posted. Thank you

@Ericisme21 Год назад

@@paultownsend2664 got it working. Thank you so much!!

@paultownsend2664 Год назад

@@Ericisme21 Your welcome I’m glad to help.

@paultownsend2664 Год назад

@@Ericisme21 Question, did you connect the monitor cable or the rocker cable in yours? Also, what dip switch settings did you set?

@geoffevarts1450 Год назад

Well had to pull the kit out.. :(The audio installers couldn't get pass the Carplay Logo. Any idea what they're doing wrong? I have a 2017 without navigation

@profsg Год назад

I'd suggest try these if possible: 1) Use USB to connect and test the Carplay module. Make sure you give permission on the phone to allow access. 2) Try another/newer phone to test it. If none of these works, it's probably a defective product.

@geoffevarts1450 Год назад

Thanks so much Professor

@geoffevarts1450 Год назад

Tried the above and no luck unfortunately,

@fixingproblems3183 Год назад

Joystick does not work well with road top. Other brands have similar issues, maybe with future software updates they can make it more stable. Right now if you want to pause a song it will make a call. Professor recommended going left and right option, even then it’s annoying and frustrating. At a price tag of $275, it may not be worth it.

@profsg Год назад

Agreed that joystick is not easy to use. For me, it's something I can get used to but understand this may not be the case. I am not sure how much improvement a software update can have on this. After all, the Carplay interface is not the ideal use case for the joystick hardware.

@fixingproblems3183 Год назад

@@profsg Professor you had best luck with LX570 setting to remove echo for telephone conversation? I contacted the seller and he did not have best setting for RX350.

@profsg Год назад

@@fixingproblems3183 Yes, I think that's what I ended up using. It fixed the phone echo problem (for the other party on the phone) on my RX350. It does require a restart to take effect. If none of the pre-configs works, you could possibly play with the detailed settings in the config and create a custom config for your vehicle. I believe that is possible but time consuming to test and figure out.

@harpreetdhanoa1231 Год назад

Would you recommend this ??

@profsg Год назад

Yes. I’m very satisfied with the installation six months later. You may check out my four month review video here: Lexus Carplay Upgrade 4 Month Review and Tips ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-yaBkp1MbwIU.html

@mangoesgonewild Год назад

Hi, thank you for making this tutorial! I’m at 2:56 in your video and my radio in my 2018 RX350 is stuck/jammed on the bottom left corner (I double checked I removed both bolts holding it in). I can easily slide the passenger side out but if I pull it too far it makes a clicking noise like something plastic might break on the left driver side. I tried pulling hard but it won’t come out at all from the bottom left side and I’m afraid to pull harder so I don’t break anything. Any tips/suggestions?

@profsg Год назад

I cannot think of anything holding it back if the bolts and trims have all been removed. On the right, I know there is a SD slot for map upgrade and there are clips around that area. Maybe it’s something different on your configuration. Here is a picture of it slightly from the left: images.app.goo.gl/8Z92fVxXd1L5jzSW8 Hopefully this gives you some idea. Keep us posted of how it goes.

@mangoesgonewild Год назад

@@profsg I took another look in the morning and realized I removed the wrong bolt on drivers side. I accidentally removed the one facing the seat instead of the one above it. Just finished the install and it’s great so far, can’t believe Lexus didn’t put this into the car in the first place! Thanks!

@profsg Год назад

@@mangoesgonewild Great! Glad to know it worked out.

@victorcui5895 6 месяцев назад

Hi!How is your newly installed system? Is the job stable? I also want to upgrade.thanks!

@mangoesgonewild 6 месяцев назад

@@victorcui5895 Hey, overall it gets the job done and gives me access to wireless CarPlay which I like. The thing I don’t like is it randomly crashes sometimes or the screen goes black randomly and I have to put my phone in airplane mode/reconnect to CarPlay while driving to fix it (tried all the settings but it’s a persist issue). The biggest pet peeve for me is I have to manually change from the default “CarPlay” audio source to the car Bluetooth source on my phone every single time I turn the car on or whenever I get a phone call. It’s annoying but overall it works and it was a cheap solution that I can live with for a few years until I sell the car.

@kallimathp1 2 года назад

Does the Audio mode need to be in AUX for driving instructions, or is there any setting to change so that the instructions are heard while playing music either on Radio, bluetooth or USB

@profsg 2 года назад

Yes, it does. Once in the CarPlay mode, the phone’s audio output goes to AUX, e.g. for voice guidance, music, etc. There are radio apps that you can use on the phone so you can stay on AUX. I discuss the setup and options in the CarPlay review video. Feel free to check it out. Lexus Carplay Upgrade 4 Month Review and Tips ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-yaBkp1MbwIU.html

@kallimathp1 2 года назад

@@profsg THanks, Is there a way to route the music through bluetooth, coz, spotify routes through bluetooth and voice guidance through AUX so they do not go together

@profsg 2 года назад

@@kallimathp1 I see. If I understand your problem, then there should be an easier solution to direct Spotify output to AUX. Normally, all audio output from your phone goes to AUX and Spotify as an app should follow that too. If it doesn't, you can disconnect/forget your phone's connection to the original Lexus bluetooth and Spotify will have no other audio output but AUX. On a related note--iOS has options to switch between different audio outputs for phone calls (Settings under Accessibility -> Touch -> Call Audio Routing) and I suspect Spotify uses something similar. I don't use it but you can look into related options/settings too.

@patrickmaerean5162 10 месяцев назад

I tried the same module in my car and i have got a lot of dash errors but everything is working ok, why?

@profsg 10 месяцев назад

What kind of dash errors? The module should only affect the infotainment display and audio with correct wiring. I haven't heard about "dash errors" but am happy to look into it.

@patrickmaerean5162 10 месяцев назад

ABS error, popup hood, brake system

@profsg 10 месяцев назад

@@patrickmaerean5162 This is unrelated. You need an OBD2 scanner to see what the exact problem is. If your car is due/overdue for a brake/ABS fluid refresh, here is a related video: ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-mL1mVPpd9qs.html

@Gychen888 Год назад

Thank you!!

@profsg Год назад

You're welcome!

@nathannguyen8589 2 года назад

Does it work for both IOS and Android devices?

@profsg 2 года назад

Yes, it supports both Apple CarPlay and Android Auto. I discussed this in other review video.

@smorrow0816 Год назад

I’m guessing you had an Android. If I have an IPhone, I assume I would need the usb cable you tucked away?

@profsg Год назад

Either way, bluetooth or USB, works for iPhone. If you use USB, that will charge your phone while in the carplay mode so it's good to have the USB option available. You can check out my follow-up review video here: ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-yaBkp1MbwIU.html

@willl7087 2 года назад

Professor: I recently installed the same aftermarket CarPlay module (branded Nauturbo) in my 2017 RX 350. Everything seems to work fine except when I'm navigating in the CarPlay interface using the Lexus joystick, it also interacts with my original Lexus interface. For example, if I moved the joystick around in the CarPlay module interface, and make selections, it also interacts with whatever is being controlled on the Lexus interface. This is extremely annoying as it would unknowingly change settings in the Lexus interface. I tried changing the DIP switch settings, reconnecting all cables and nothing seems to work. The Nauturbo seller has been very responsive but they cannot figure it out either. Is my unit defective? Any suggestions?

@profsg 2 года назад

If DIP switches are all correct for your model/configuration, I suspect it might be something to do with the CAN cable/connections. Make sure they are chained together. My theory is that while the Carplay module "thinks" it is in the carplay mode, somehow the original Lexus unit still receives commands on its UI. It could be incorrect DIPs (which you ruled out), faulty connectors/connections, or a defective unit.

@willl7087 2 года назад

@@profsg Thank you professor. The seller technical team is asking me to connect an extra harness which came with the kit to my joystick, but I'm skeptical it'll fix the problem. I'll report back once I do. If not, I will likely ask for an exchange.

@kevinlay3468 2 года назад

@@willl7087 I have the same issue

@willl7087 2 года назад

@@kevinlay3468 Sorry to hear that. At least I'm not alone. I tried everything to no avail... I'll live with it... Let me know if you find a solution!

@tubeuser617 2 года назад

Professor I have the same issue connecting to joystick. Joysticks doesn’t function

@amrinde1991 Год назад

Does the reverse camera and surround view work, if in CarPlay mode

@profsg Год назад

Yes, the camera does. Whenever it is in R, the rear camera will show as usual even in the Carplay mode. I don't have the surround view so I am not 100% sure about that, but suspect it will continue to work.

@amrinde1991 Год назад

@@profsg Really appreciate your response, thank you

@blakehendricks7870 2 года назад

Is this the same for a 2015 Lexus rx350

@profsg 2 года назад

It is a different model generation with a different configuration. That said, the unit I purchased appears to support models starting 2014. So I suppose it will work but wiring can be different. When you purchase, make sure you verify with the seller your model year and configuration so you get the correct cables.

@rezafaraji8855 2 года назад

does it support 360 camera?

@profsg 2 года назад

Yes, it does according to the manual, though I don’t have a 360 camera to test it. I did receive wiring for that, and it’s part of the USB cable/cluster. The manual has instructions on wiring sequences and settings on that for original and aftermarket cameras so I suppose it’s well supported. But again I haven’t tested it.

@VuNguyenn 2 года назад

Hi Reza, I have recently installed the same units…. 360 camera all are working.

@phillyb9499 3 дня назад

@@VuNguyennI’m about to install this, any additional wires that need to be connected besides the ones shown on video? Did you have to adjust any settings ?

@harpreetdhanoa1231 Год назад

Any known issues with this products so far

@profsg Год назад

I've had no major problem with the one in video. However, if you read comments below, some people received defect products. Others encountered issues such as engine noise because of the ground wire connection, which can be fixed. Feel free to check out my 4-month review video: ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-yaBkp1MbwIU.html

@zongwang458 2 года назад

However, I got one message in the entretien table said engine oil need to change, i just done the recision I don’t know if you got this message or not

@profsg 2 года назад

Interesting! This must have come from your original Lexus system where you can set oil change/maintenance schedules.

@csrlee 2 года назад

I got this too... I just reset it. weird!

@kdoleyres Год назад

I def need a firmware update i have no acess to HDMI in (app missing)

@profsg Год назад

You can get in touch with the seller to get that done. I've heard positive reports of issues being resolved with a firmware update. Best luck and keep us posted!

@Automatik1 2 года назад

I followed your video and installed one today on my 2017 rx350 f sport without navigation (7.1" screen). Different cords in the back than yours but everything seems to be connected correctly, however there is No audio. I made sure aux setting is on and removed the oem Bluetooth connection on my phone, still no audio. Any suggestions?

@profsg 2 года назад

The best way is to reach out to the seller's customer services. I emailed them problems/questions I had and they were quite responsive last time I contacted them. That said, a couple of places you may check: 1) Sometimes we overlook things so double check the audio is on with a decent volume so you know it is indeed no audio output. 2) I am not familiar with your model and how the connections work. But I remember there was an audio output from the Carplay box, which should be connected to the back of the radio unit and chained with the original audio cable. But again, I'd contact the seller first to see if they have advice. Look forward to hearing about your findings and solution...

@Automatik1 2 года назад

@@profsg I appreciate the quick response. I reached out to them and they finally responded back. For my model, there is a ground wire coming out of the USB/video connector plug that needs to be spliced with another Audio - ground wire coming out of a separate connector plug. They're labeled as "Ground" and "Audio-ground". After I did that the audio worked. Unfortunately there's no mention of this in any of their instructions or videos. Hopefully this will help others as I'm sure it's a common problem. Thanks again!

@jonathanwu4004 2 года назад

@@Automatik1 any tips on how to splice them together? Did you simply twist them together?

@Automatik1 2 года назад

@@jonathanwu4004 yeah, I just stripped the wires, twisted them together, and then put heat shrink tubing over the connection to secure it in place.

@jonathanwu4004 2 года назад

@@Automatik1 I’ll give that a try, thank you! 🙏

@bunkymears1080 3 месяца назад

What’s the dip switch position for 14 Ls460

@profsg 3 месяца назад

It depends on your Lexus touch/remote control and button configuration, e.g. Rotary Knob, Touchpad, Remote Lever., etc. For Roadtop units, see pages 6 - 8 of this manual: www.clublexus.com/forums/attachments/is-3rd-gen-2014-present/480572d1593099418-new-wireless-carplay-androidauto-for-oem-10-25-screen-user-manual-for-lexus-remote-touch-version.pdf

@bunkymears1080 3 месяца назад

Thanks for your reply i will try them my book is different hopefully it works 4th time taking car apart when i long press menu button regular menu screen

@profsg 3 месяца назад

@@bunkymears1080 sounds good! Do test it before reassembly. Contact roadtop support if the issue remains.

@leonchea8235 2 года назад

Can anyone help with Mirror Link this system?

@profsg 2 года назад

The unit supports Carplay and Android Auto. I am not sure about MirrorLink, if you are referring to a specific technology or simply trying to mirror your phone display to the screen. There is a feature in the unit (on the carplay module's system menu) to do mirror display (like airplay) but, personally, I don't like the feature. You have to disconnect existing carplay to enable that feature, which doesn't fully utilize the screen (12-inch screen). It worked when I tested that feature, but have rarely used it.

@geoffevarts1450 Год назад

Has anyone installed a non navigation on a 2017 RX 350? Just ordered one and debating about trying to install it myself or bringing it to a shop.. Any advice would be greatly appreciated!

@profsg Год назад

Some in the audience have installed it. Here is a related thread under this review video: ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-yaBkp1MbwIU.html&lc=Ugw-canv1xyI6SWvYaR4AaABAg

@geoffevarts1450 Год назад

Thank you.. I can't seem to get passed the Carplay Logo.. Not fully rebooting.. Any suggestions would be greatly appreciated

@wayneg818 2 года назад

Can i have the link of the products ?

@profsg 2 года назад

Sure. This is the one used in the video: ebay.us/T5h7TK

@hendrix1084 Год назад

Hey will this work for a 2013 Gs350?

@profsg Год назад

The one on video works for 2014 and later models. See description for the link. For earlier models, you may contact the seller or do a search.

@geoffevarts1450 Год назад

Having issues of the Carplay not fully booting up... Just the Carplay Logo.. Has anyone have this problem?

@profsg Год назад

I experienced that a couple of times. Had to reconnect and it went back up normal.

@geoffevarts1450 Год назад

Thanks!

@gabrieljang1375 2 года назад

Am I able to run Waze on the background while I was on the radio?

@profsg 2 года назад

I use Google/Apple Maps a lot while listening to radio (TuneIn app) and have no problems. So I suppose that should work with Waze too. However, if you are on AM/FM, you won't have voice guidance because carplay uses AUX for audio output. Maps will still works; there is just no audio from it.

@justinmckelson694 Год назад

@@profsg Hi Professor, thanks for all your responses, if using the configuration as above with AM/FM radio on and using maps with no voice guidance what would happen if there was an incoming phone call? Would OME Bluetooth still function to handle the call. Looking at getting this for the in-laws but they use AM/FM a lot. Thanks

@profsg Год назад

@@justinmckelson694 Good question! I don't use the original bluetooth anymore and don't have a concrete answer. I think the OE bluetooth may still pick up incoming calls. The alternative is to install the TuneIn app and preset local radio stations for your in-laws so they can use remote/touchpad/lever to select and listen to the radio.

@justinmckelson694 Год назад

@@profsg Thanks👍

@mangoesgonewild Год назад

I was wondering if anyone else has the issue of Bluetooth skipping two songs instead of one? It was fine the first day but after that it always skips two songs in a row (i noticed this is not a problem when connected to CarPlay Audio but I prefer Bluetooth audio because it sounds way better than the CarPlay one)

@profsg Год назад

Sounds like some interference of the two connections, bluetooth vs. carplay. Perhaps both attempt to play the next? Try disabling one at a time and test whether each works individually. Also check Carplay system/OS settings to see if there is any audio/play-related option.

@profsg Год назад

Two options perhaps you can review in Systems: One is "Using Car's BT Phone"; mine is turned off. The other is Wifi Channel, which is unlikely related.

@mangoesgonewild Год назад

@@profsg I will try that tomorrow. I turned ON “Using Car’s BT Phone” because I thought that meant it would default to Bluetooth audio always but I will turn it off again. My wifi channel is on 36, by default. Thank you! I noticed when connected to CarPlay audio, the songs won’t skip two, it’ll skip normally. When connected to Bluetooth audio, it’ll skip two songs going forward or back.

@mangoesgonewild Год назад

I was able to fix it by switching from “No swap” to “swap” 😁 Thanks again for the great video!

@alperbakrdogen9685 Год назад

where can i supply this module ?

@profsg Год назад

The link to the one I used in video is in the description, and I copy it here: ebay.us/T5h7TK There are multiple vendors/brands and you can find more on eBay, etc.

@thomasone1108 Год назад

Anyone able to get up down joystick movement working in the Android Auto? For me works in the setting, but not AA or carplay.

@profsg Год назад

Take a look at the review video at this time: ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-yaBkp1MbwIU.html Make sure you select "Remote Lever" (joystick) in the system settings, and use Left/Right movements to scroll (move) up/down. This is not the most natural but it works best with this hardware configuration.

@thomasone1108 Год назад

@@profsg This work wonder! Thank you 👍

@zakir8 2 года назад

I just installed Roadtop and I have to say I am bummed that it’s not seem less like some other solutions like Beat Sonic. It is good enough if you are using Siri to do most things, but using the remote is no fun. Sometimes getting it in precise location is a challenge while driving. Which mean taking your eyes off the road. Also, one of the biggest issues I found is that this system overlays CarPlay on top of the OEM software which is fine. But the biggest problem is that when the remote is moved and clicked, it’s also interacting with OEM screen in the background while showing CarPlay screen. So, the haptic feedback you feel in the remote is actually from OEM software. The clicks are as well which tends to switch back to oem screen for a bit. Like when accidentally clicking on Pandora. Is this also your experience Professor?

@profsg 2 года назад

Looks like multiple people reported having the same issue. I didn't encounter it but suspect it is an issue with wring or DIP settings. Perhaps a defective unit? What does the seller/support say?

@zakir8 2 года назад

@@profsg I have tried many different connections. Firstly, they had me try different dip switch settings. 1,3 and 1,2,3. That didn’t work. Then they made me use the other wires to connect F# rocker controller to C# Can controller and E# can controller to A# old car no split screen. My remote didn’t function at all with this settings. I sent them all the videos and they said they are consulting with their engineer.

@luisramirez6970 Год назад

@@zakir8 Hey! I had success connecting the 15H-LEX-KT cable and the F# to C# and E#->A# on DIP setting 1,2,3 on, the rest off. I had trouble understanding their instructions, but they sent me a diagram that somehow I made sense of and that put everything together. The 15H-LEX-KT cable basically connects directly to the Joystick module and prevents input from being sent to the OEM system. Let me know if I can help you in any way. I'm very happy with the device so far.

@zakir8 Год назад

@@luisramirez6970 Thanks for the response. I believe I did try to do that. Maybe I didn't read their diagram properly and will need to try it again. So what you are saying is I need to connect 15H-LEX-KT directly to the joystick module which is by the remote itself? Or is it in the F# to C# and E# to A# exchange itself? I think pictures would immensely help out here.

@luisramirez6970 Год назад

@@zakir8 Yes that is what I am saying. You need to do all of it, connect the 15H-LEX-KT to the joystick and the other connections as well, then set the right DIP setting. I made a short video of the pictures and video I had, check out the description for all the info, hope that helps. ru-vid.com6Yy1FERE2XU?feature=share

@mdahmed3357 2 года назад

i need fix apple pay my car .can you help me please

@profsg 9 месяцев назад

Thanks for visiting! Feel free to post more specific questions.

@ZiYang-fh5ub Год назад

Thank you Professor's Garage. I just installed it to my Lexus RX350. it works well except the joystick. when I tried to move left, sometimes it moves right. Does anyone have similar issue?

@ZiYang-fh5ub Год назад

I see the actual issue. It’s interacting with the original Lexus system. Not sure if anyone has a solution yet.

@profsg Год назад

There are some settings related to joystick (e.g. left/right vs. up/down): ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-yaBkp1MbwIU.html I didn't encountered the issue with interfering the original Lexus infotainment but have seen other people reporting that. It might be a faulty unit or due to incorrect DIP settings? Contact the seller support to see if they have a solution.

@fixingproblems3183 Год назад

I have the same issue with the joystick not stable

@ZzzMajinzzZ Год назад

I want this. It is out of stock…

@profsg Год назад

I am not affiliated but for the product I purchased, here is the company's site: roadtop.com/ You can contact them regarding where they have in stock.

@tjmasterbarber2664 Год назад

Jesus Christ the process is horrible! you miss a screw or a piece. you are literally screwed

@profsg Год назад

The process does require patience. I did lose a screw and had to replace it. Not the end of the world though. Find a time when you can do it slowly and don't have to worry about putting everything back together in an hour. :) Good luck!