Lexus CT200H Check Hybrid System Fixing Reset Fuse

Подписаться 18 тыс.

Просмотров 28 тыс.

50% 1

This Lexus CT200H got a Check Hybrid System indication
it could be many different reasons why this error has occurred and overheating could be one of them this video might help you to reset your hybrid vehicle... diagnostics are required to find out why this happened, that's why resetting is demonstrated in this video is just a temporary fix...
if your check Hybrid System indication is on your hybrid drive is disabled you will be able most likely temporarily to drive using normal mode with the engine constantly on.
sport or economy modes are disabled...

Опубликовано:

21 окт 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 41

@AdrianoBoller 9 месяцев назад

Your video is excellent, I did exactly that, but the warning triangle and the hybrid check message appear and I go to the fuse panel and remove the white cable for 5 minutes and it goes back to normal after a few days and the hybrid goes back to alert , I already disassembled and reassembled the entire battery, removed it and detected xinabre on the contacts and cleaned it. but the warning message still appeared, I remember that when you remove the cable from the fuse panel everything is 100% and when using the air conditioning it goes out.

@gavrilovas1 9 месяцев назад

Consider replacing hybrid battery 🔋 pack.

@Zierack Месяц назад

Thanks, I just followed your clip and was able to fix the Check Hybrid System error.

@Dhistro Месяц назад

Алексей, добрый день, спасибо вам за видео! Если не трудно не подскажете в чем может быть дело? Вчера вечером завел машину а климат не горит, все работает, но не горит само табло. Когда перевожу режим фар с режима авто на выкл, все загорается. Может жело в предахронителе? Если советом поможете, очень буду благодарен!

@heokitty4355 9 месяцев назад

My car has same issues yesterday and I just parked I don’t know what to do ? And also it comes another writing on dashboard at the same time! “ traction battery preservation mood restart after shifting the P position “ this what come up Could you tell me what does this mean?

@gavrilovas1 9 месяцев назад

Consider replacing hybrid batteries pack

@leogomez9014 6 месяцев назад

Did anybody experience these warning lights with a simultaneous power loss? (Mine would not go abive 40 MPH) What did you do?

@gavrilovas1 6 месяцев назад

If you have power loss besides hybrid faulty battery, it also could be something related to the engine.

@leogomez9014 6 месяцев назад

@@gavrilovas1 I got a code for bad water pump. Replaced it and so far do good.

@MrJonathanbleeker Месяц назад

I had the same issue and my Lexus garage found out that the throttle body needed to be replaced. The whole repair cost me about 2400 dollar.

@Retrolandmark 2 года назад

What are the steps to doing this? Does the e brake have to be on while in drive?

@gavrilovas1 9 месяцев назад

the best way is to replace hybrid battery itself.

@terjeoseberg990 11 месяцев назад

My 12v battery died because the dome light was left on. Charged the 12v battery, and now I have this message and the car will turn on, but it won’t move. I tried this and it didn’t eliminate the error, so I’m looking for a different solution.

@terjeoseberg990 11 месяцев назад

I also tried removing that plug in the fuse box and also simultaneously removing the plug on the hybrid battery. I checked the voltage from the jumper cable terminal to ground and it was 0.3v, so I turned on the dome light to drain any capacitors to 0v and checked the voltage again and it was 0v. I waited another 15 minutes, reconnected everything, and my issues still isn’t fixed. I’m getting “Shift to P position to start” with I try to shift it into drive or reverse.

@gavrilovas1 10 месяцев назад

Consider replacing hybrid battery pack, it will cost you on average 1500 to 4500 dollars

@terjeoseberg990 10 месяцев назад

@@gavrilovas1, I figured out the problem. When I plugged in the hybrid battery, I neglected to slide the lever over, so the small plug underneath the connector wasn’t making contact. After sliding it over, everything started working properly.