Lifting table 1

Подписаться 352 тыс.

Просмотров 151 тыс.

50% 1

Blue motor via worm drive makes two orange shafts rotate in opposite directions.
Orange cranks fixed to the shafts move up-down green table thanks to tangent mechanisms.
Forces applied to all four legs of the table at the same time make the table move easily.
This mechanism is used for large tables.
STEP files of this video:
www.mediafire.com/file/f947fs6...
Inventor files of this video:
www.mediafire.com/file/t7vxc2f...

Наука

Опубликовано:

23 фев 2019

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 40

@ofar4452 5 лет назад

Love the simplicity to keep things level and translating at same time/rate. As noted on other comments this needs to be engineered to match needs for lifting. Great job!

@JAALMARZA 5 лет назад

Nice mechanism.Thanks for sharing!

@Praxis4RageBaiting 5 лет назад

Oh wow that is a huge jump in subscribers and viewers. Congratulations :)

@livinmarcenariaartistica8212 5 лет назад

você é o mestre da mecanica , muito bom

@mrayco 5 лет назад

Awesome ,,, you are super master with this. Thanks

@saurav9231 5 лет назад

U r genius...

@hayel2015 5 лет назад

Great 👍👍👍

@thomashoffmann4504 3 года назад

Nice animation. But, I don't think easily doable. The torque created by the lever will be huge. The gears will see a lot of forces.

@CompanyofHeroes999 Год назад

Of course it's doable. Just have to dimension everything right. The upper part of the table can be made of aluminium, and this table could be used for light loads in the end, if bigger module gears don't satisfy.

@thomashoffmann4504 Год назад

@@CompanyofHeroes999 everything is doable, but at what cost.

@CompanyofHeroes999 Год назад

@@thomashoffmann4504 All of the parts shown here are so inexpensive. And would stay that way I'm sure even if the construction is a bit beefed up.

@sergeybabuka1800 3 года назад

за оранжевые вилки можно задеть ногами или зацепиться штанами , а в целом регулировка высоты неплохо задумана

@MattSeals 5 лет назад

Wow, stunning webvideo. Thnx ...

@piotrmecht2500 5 лет назад

What software do you use to model your assemblies, Mr Thang?

@thang010146 5 лет назад

It's Autodesk Inventor.

@livinmarcenariaartistica8212 5 лет назад

tem algum exemplo de tv lift ?

@TechsScience 5 лет назад

I am going to make a model ot this

@onshreeelectricalss7020 3 года назад

Good

@mrkucz 5 лет назад

table wouldn't be able to hold much on account the lifting arms might break or bend

@jimbarchuk 5 лет назад

I thought about that, and other potential point-failure issues. Some bits look flimsy because they're drawn only enough to get the point across. To design it you need to name parameters, table size needed, expected weight to be supported, travel speed needed (it'll be slow.) The drawing is 'designed,' not 'engineered.'

@dielaughing73 3 года назад

Especially at the halfway point..

@The-Lean-Engineer 3 года назад

Is there any stopper Mechanism?

@The-Lean-Engineer 3 года назад

Anyone can suggest a video for motor selection?

@XYZ-lw1gu 5 лет назад

Very dangerous technical concept. Huge strength on the lifting arms and transmission. Stupid idea .

@dckakadia Год назад

Can you suggest any hydolic lift with single cylinder table size 2500mmX2500mm with 20 ton weight lifting capacity?

@thang010146 Год назад

This might be suitable: ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-ui9ysjCUMdw.html

@shreyaskhade6290 5 лет назад

How are rollers and the forks mated?

@thang010146 5 лет назад

Cylinder on plane joint.

@mojtababayest9491 5 лет назад

The table must be empty or it needs a big motor to lift it.

@mrayco 5 лет назад

This mechanism has self lock 🔒 and you can left it manual if you like it doesn't take big forces.

@thomashoffmann4504 Год назад

@@mrayco did you calculate the forces?

@mrayco Год назад

@@thomashoffmann4504 worm gear handle all that load ...I didn't calculate anything

@epiespinoza4941 5 лет назад

Whats the details on this to build it

@jimbarchuk 5 лет назад

These drawings are 'designed,' not 'engineered.' To make the design 'buildable' you first need to name parameters, table size needed, expected weight to be supported, travel speed needed (it'll be slow.) Next is some That Looks About Right guesstimates of raw materials needed. That will vary drastically depending on whether you want to lift a muffin or a motorcycle.

@thang010146 5 лет назад

Thank you for your detailed explanation.