Logitech pedal modification using a brake cylinder and a pressure sensor and an Arduino.

Подписаться 94

50% 1

Logitech Driving Force GT pedal modification using two sets of pedals and a pneumatic cylinder as a brake cylinder and a pressure sensor. Hall sensors are measuring angle of the pedals. An Arduino pro micro is controlling the system.
Update:
1)Precharging method B (2:23) Maybe it is not a good idea to leave the cylinder in a freezer too long (it could be bad for the seals). Better idea is to suck freezer's cold air (pulling the piston rod) into the cylinder and then tighten the adapter quickly.
2)If you want to make the pedal stronger you could use steel bracket (1:35) instead of aluminium and you could fill the empty space between bracket and pedal using epoxy.

Опубликовано:

20 окт 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 16

@SianaGearz 5 месяцев назад

Interesting chair hold down solution. I guess you could also place stoppers under wheels and also use something that would lock seat piston top and bottom against rotation. There is also a sim replacement chair piston with a toggle for that, for sure modified from a standard one in some fairly easy manner, if one were to just figure out how.

@hekka7270 5 месяцев назад

Thanks for the tip!

@KickedChango 4 месяца назад

Insane mod! Why not make a steering wheel mod for the driving force gt like a gt3 or a formula style, that will be a very good video, like cuting the original steering wheel and 3D printed a very cool one

@hekka7270 4 месяца назад

Thanks! I have (very hazy) idea of cutting DFGT steering wheel so that it looks like yoke and using some kind of slide building aeroplane controls. DIY force feedback controls would be cool but probably out of my league.

@KickedChango 4 месяца назад

@@hekka7270 I love your content! I’m following your channel because I love this kind of mods! Thank you for taking the time to make this!

@RadicalDrive-jy3cw 2 дня назад

hello, its me again, can you helpme with the code of the arduino? pls!!

@RadicalDrive-jy3cw 5 дней назад

Can you helpme with the schematic for a thrust master pedals, I did the sam and I want to use 2 potentiometers and 1 loadcell or hall sensor

@hekka7270 5 дней назад

You can use hall sensors or potentiometers (or pressure sensor) same way. They all need supply voltage (usually around 5 V), ground (0 V) and signal wire (check my videos circuit diagrams). I haven't used load cells so I don't know how to connect them. However there are many RU-vid videos which have information how to use load cells.

@RadicalDrive-jy3cw 5 дней назад

@@hekka7270 So what you’re telling me is that I can combine 2 potentiometers and 1 hall sensor with one Arduino? And use mmjoy2 right?

@hekka7270 5 дней назад

I am not familiar with mmjoy2 but don't see any reason why it wouldn't work. You can use common supply voltage and common ground for potentiometers and hall sensor but they need separate analog input pins on Arduino.

@RadicalDrive-jy3cw 5 дней назад

@@hekka7270 If it’s not a bother, could you give me an idea of what other program you use other than mmjoy2, I’ve been following your channel for a long time, but with another channel I have, I’m going to check between your videos, to see if in any of you talk about the software you use

@hekka7270 5 дней назад

I am using Arduino Joystick Library (by MHeironimus). Fist line in my program "#include " means that my program is using "Arduino Joystick Library"-library software. I think mmjoy2 is probably easier since you don't have to program anything, you only upload mmjoy2 to Arduino. I like Arduino Joystick Library more because it "forced" me to learn something about programming and I can change features of pedals (or joystick) if I want to. Some people are using Teensy controller and they say it easy to operate but I have zero knowledge of it.