Mac 335 McCulloch Chainsaw Oil Pump Servicing. 

Like you I bought one of these 2nd hand something like 10+yrs ago. I did put a new bar and chain on it back then. The bar is still going and have replaced the Stihl chain as it broke a year ago. Got the shop to repair the break and this chain is now a backup. Am in the process of replacing the drum and spindle bearing. Overall I reckon its been an awesome saw and I've learnt a lot about this chainsaw while doing my own repairs and maintenance over the years. Note for others, parts for these saws now are a Husqvarna 142, 137 parts from my experience so far. If I could buy another one of these, I would.

Mac-335 is exact copy of Partner-351/371/391 (or Poulan-2250/2450/2550) - body color and labels are the only difference. So you can use equivalent parts (for example - starter, ignition coil, carburetor, filters, clutch, clutch cover with chain brake, oil pump, crankshaft bearings/seals, etc.) from these chainsaws.

Thanks for doing the video. It got my chainsaw fixed and back in use. I used a spanner off an angle grinder to undo the LH treaded clutch.

One point, there's a groove on the crankshaft that the spring clips into to set the correct position. My drive spring had jumped out the groove so was not turning the pump. The pump was OK, it was the spring that had failed after 20 years! Thanks for the video.

turns out the guy i know that knows everything about chainsaws didn't know about this lol I love RU-vid and now i love you

Thanks for posting this. With regards to tensioning, if it's like my Mac Cat then you hold the bar up as far as it will go whilst adjusting the tension screw, then tighten the nuts whilst still holding the bar up.

thanks Tom - i have a similar problem on a 338 which i can now resolve thanks to your video. i did find that jambing a screwdriver into the cooling fan blades was easier than trying the prevent the piston from moving - with the same results.

Many thanks Tommy. My pump defo "Gave up the ghost" too. You saved me a lot of time figuring it out AND great tip with the plumber's spanner - I was trying to use an adjustable grinder disk remover wrench. I don't like jamming the piston with string tbh because of dirt and the risk of bending the con rod, I would PREFER to have two locking nuts at the other end of the crank shaft (ie where the pull string operates).

Excellent video, Tom. I'm waiting for a replacement pump to be delivered and, hopefully, you've saved me from having to replace the chain saw. Much appreciated.

Rather than using the rope trick to stop the engine rotating when removing the clutch assembly, take off the recoil starter cover (4 screws) and use a 13mm socket/spanner to hold the other end of the crankshaft. The front handle offers a way to stop the spanner moving.

Hi just found this video, I replaced one of these today but in the kit came a new spring so I fitted that, I was a bit concerned as you can’t really tell if the spring is spaced correctly, but I got it back together and it does pump oil, so I take it it must be ok. I’m not keen on the design but it works and the parts were dirt cheap. Good video🙂👍

Thanks for the vid found it really useful , :-) My oil pump was full of gunge ,i stripped it down to clean it now its as good as new .. to get the clutch off i used a old spanner that fitted the recesses then gripped the spanner with an adjustable spanner..

believe it or not most oil pumps break like that because someone forgets to fill the chain oil. So when you put gas in a chainsaw you always put chain oil in it same time. By the way that clutch will tighten up automatically, so when you start it and start using the chainsaw it'll tighten up. so don't worry about that being really tight. If you don't have a spanner wrench I've used a screwdriver and a hammer, (in the little holes) doing that may put some nicks on your clutch but just as long as you don't whack it really hard, it'll loosen up and won't hurt anything.

Hi, hole at front of tank is for lower screw to mount the bumper spike / dog. A cut to size 5.5 mm dec (Drill-Dex)5/16th hex head, coarse self tap thread screw makes a good substitute. Short enough to NOT penetrate the oil tank wall.

Good job, l replaced my pump in no time thanks to you, well done and thanks for the video.

Thanks from. Jamaican. Appreciate you 🙏

como poner el carburador en motosierra McCulloch 335 si podria acer un video referente se lo agradeceria gracias

This chainsaw is exactly the same as my Poulan Pro 260. Just the name and colour is different

I would like to see the saw run and see the oil come off the chain.

Thanks mate just what I wanted to learn 👍🏻

Thanks sir, you just saved the day.

Great video Tom very informative many thanks for sharing

I would clean bar oil tank dirt-may have got from there into pump seized it up and drive stripped. Great vid ver usefull

Before doing this, pull out the oil tube and blow it through with compressed air..

Nice tutorial! But I must say that I prefer to buy a better quality chain and sharpen it regularly!

Great video mate.. just stumbled across the video

Boa noite tenho uma macculloch 335 , gostaria de saber se o combustível é colocado com óleo 2 tempos no tanque dela obrigado!

Obrigado pela dica amem

como poner al carburador y en que posicion va puesto en motosierra mcculloch

Fantastic video, thank you

Hi, problem is people using dirty engine oil due to poverty or not cleaning around filler cap prior to opening to fill. best is to brush crap out and fill from clean container will chain oil.

Merci pour le tuto.

thank you, excellent video and exactly what I was after for my mac 335 (also an e bay "success"). Hope you get a decent income from it :)

Hi, have you got any information on what kind of age these are as we are looking at buying a used one of the same model. Thanks

Tom check out how to file a chain old faller tips.buckin billy ray I think you will save $$$ on buying chain.

question, which way does the oil line go from the oil tank to the pump and to the oiler?

Great vid, my chainsaw seems to be losing way to much oil to literally a dry tank. What could that be just adjusting?

Hi there Tom my name is Jonny I have the same chainsaw as you have in this video and was wandering what size chain you use on your chainsaw so I can buy the right one for mine

Needs more cowbell

great vid!

that looks very similar to a poulan saw

thats a poulan lol must have had a contract with mac at that time

I need some advice about my chain brake cover. When I bought mine second had from a car boot sale it was missing the chance brake band spring and pin out of the chain brake handle do know where I can buy the spring and the pin from. I've ordered the band

610 saw. oil. pump. maintenance

Mine constantly start and cuts out after a few seconds any ideas?

Bloody nylon sprocket Always put something week to break don't they

P