Mach3 Rotary Axis configuration

Подписаться 2,9 тыс.

Просмотров 30 тыс.

50% 1

On this video tutorial, originally posted in Spanish; is intended to show how I configured the rotary axis on my CNC router, perhaps will serve as a guide on a similar situation for somebody looking for information on this subject, I am not an expert by any means all the steps that I use in this video I learned online and by trial and error. I start by showing how I calculated the gear ratio, followed by calculating the steps per degree for the main shaft gear

Хобби

Опубликовано:

30 июл 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 43

@mikruson 4 года назад

Awesome tutorial Carlos,thank you very much!

@CarlosMDominguez 4 года назад

Glad you liked it!

@laszlosoproni761 2 года назад

Thank you sir, Your video helped to setup my rotary axis. Just perfect explanation. You are legend.

@CarlosMDominguez 2 года назад

You are very welcome, thanks for your comment.

@djamelweld1059 8 месяцев назад

You are the best at explaining, thanks 👏

@CarlosMDominguez 8 месяцев назад

Glad you think so! Thank you for watching!

@pauldiaz4273 3 года назад

Great explanation thanks señor carlos!

@CarlosMDominguez 3 года назад

You are welcome!

@frankmardey2354 3 года назад

Thanx for this explanation. Very usefull

@CarlosMDominguez 3 года назад

Glad it was helpful!

@nikoanggriawan303 Год назад

Perfect explanation..❤ thanks a lot

@CarlosMDominguez Год назад

You're welcome 😊Glad you liked it!

@mecanizadosgrela7380 7 дней назад

Thanks for the video

@CarlosMDominguez 7 дней назад

@@mecanizadosgrela7380 your welcome

@Mewanrahnam575 3 года назад

Thankyou..keep going Sir.

@CarlosMDominguez 3 года назад

Always welcome

@umargul5644 4 года назад

Great job thanks sir

@CarlosMDominguez 4 года назад

Most welcome, thanks for watching!!!

@josiascnc4539 3 года назад

Excelente vídeo...

@CarlosMDominguez 3 года назад

Gracias!

@owenroque3633 4 года назад

thanks for the info

@CarlosMDominguez 4 года назад

Any time

@nick-k7k 4 года назад

Hello, I'm new to mach software. On the screen, it is showed only a 4th axis (only one rotary) but I found in many forums that it can support also the 5th axis. Please help me to understand If you can use the mach3 board for 5 axes and with which software

@CarlosMDominguez 4 года назад

I am not very knowledgeable on more than 4 axis machining, however yes you can use 5 or more axis with Mach3 providing that you have a control board , to design and generate the g-code you can probably use a program like Fusion 360, or similar. Good luck.

@ambujsenapati3597 4 года назад

Thank you, sir. It's very helpful , if a program info about rotary ATC settings with mach3 .

@CarlosMDominguez 4 года назад

Thank you!

@hosseindten2457 Год назад

thank u thank u thank u So Perfect

@CarlosMDominguez Год назад

You're welcome 😊

@bocus9001 Год назад

thanks so much sir, please can you help me i installed rotary axis in pins of y axis as my machine setup design is using x- axis , z-axis, y axis as rotary axis and a-axis is tilting spindle head as i have mach3 4 axis not 5. how can i program it or using a definite postprocess which suits my machine design? i'm using powermill

@CarlosMDominguez Год назад

I am not familiar with Autodesk software, so I don't think I can figure out a post processor for it. Sorry I can't be of much help, (other than what I explained on the video). Thanks for the comment and good luck.

@hinrigardehes3253 3 года назад

Hello, can I make a digital machine without connecting the RS 232 cable from the driver to the computer with the mach3

@CarlosMDominguez 3 года назад

Mach 3 is a parallel interphase, but you could buy a parallel to USB adaptor I imagine if your controller is USB, I never used anything other than 25 pin cable though. Good luck.

@brayanestevensfrancopereir5270 3 года назад

If my controller does not have micro steps, how would the formula be, my machine control it with a richauto a11 ??? what should i do to be able to calibrate the 4th axis

@CarlosMDominguez 3 года назад

You are going to have to search for specific information about your controller, maybe some RU-vid videos on the Richauto a11, seems that this controller uses its own controlling software independent of the computer, I am not familiar with it. So, I'm sorry I ca not help you with it. Good luck!