A quick look at how to maintain your tailstock to keep it turning easily. Want to support my channel? www.buymeacoff... Link to thread lubricant test: benmlee.com/4runner/threads/threads.htm
My tailstock was binding so bad so I decided to take it apart. I couldn't figure out how to take that retainer ring out and there was a set screw on it. This video just saved my butt for sure. Thank you!
Thanks Gord. I had noticed the tailstock on my DVR tightening up, and today it just became unbearable while drilling out a box. I remembered this video from whenever and was able to find it readily. Very clear instructions, and as I have the same lathe (still grey, of course) it was real quick and easy, problem solved. Thanks for posting this.
Woodbees Gord there is a dry lub ' that I use on my lath every where it is needed. It goes on wet and dries in a few minutes. It won't attract any dust. I get it at Lowes. great job teaching in your vids
Thank you, Bram. I must do a better job of maintaining my equipment so I don’t HAVE to maintain my equipment! Thank you for watching! Take care, .....Gord
I have the DVR xp and about a year ago upgraded to the NOVA DVR XP CONTROL PANEL UPGRADE (SKU 55523). It does everything your current panel does and had some more features including a speed control knob. At first, not sure I was going to use the new features much but the more I use it the more I use them. Really enjoy your videos. Learn a lot and enjoy a little humor.
Thanks for the video. I just cleaned mine and was surprised at the amount of gunk inside. I used a dry lubricate in hopes that it will not attract dust. In most cases WD40 is my first choice.
I’m happy if the video helped or motivated you to maintain your tailstock. In my newest video I showed what I ended up using instead of WD-40. I’m very happy with it and must remember to clean and lubricate on a regular basis. Thank you for watching, Dan! 😃😃 Take care, .....Gord
Excellent informative video Gord, and I agree on using WD-40 as that is what I use! I do not have a Nova DVR but I have a Nova 16-24 lathe and when I bought it a online friend who also owned a Nova recommended to put some duct tape over the slot at the back of the lathe to help keep the dust out of the tailstock. I did that and it sure helps but after about 10 years I think that I may have to take mine apart as it seems to be getting harder to turn and after this video it should be quite easy...…..I hope!!!1 Cheers Al
I can’t believe I waited so long to do it, Mike! I have put a reminder on my phone to make sure that I do it at least every couple of months. Don’t want to let it get that way again. Take care my friend, .....Gord
Hello Gord, Another very useful video, especially so because I also have a Nova DVR XP lathe. Your videos are always helpful. Thank you. A similar video on servicing the banjo would also be helpful, in case I’ve missed something. By the way, I shorted out my motherboard following a buffing session with my Beale system. There’s only one center in the US for repairing a Nova DVR Xp, in St. Petersburg FL, and I’m in California. Nevertheless, they were helpful Although their images didn’t match my photos, I was able to reassemble my lathe and it’s working fine again. Thanks again, Gord.
I’m happy that you like the videos, Kenneth! Thank you for watching them; I appreciate the support very much. To tell you the truth I have never looked closely at my banjo. It’s never given me a problem and I’m glad you mentioned it because I think it’s a very good idea to look at it before it does cause trouble. I guess I’m guilty of ignoring things until I’m forced to take care of them. Bad Gord!! 😁 I also had a motherboard burn out a few years ago and while I didn’t have a problem replacing it - retired electrician - I was surprised at how expensive it was! Did I mention that I’m cheap? 🤣🤣 Thanks again for mentioning the banjo! I will take a look at mine tomorrow. I’m not sure it would be worth a video but I will certainly check it out! Take care, .....Gord
I have a Nova Galaxi lathe and the tail stock froze up recently. Along with cleaning the areas you did, I had to clean and hone the tail stock bore and outside of the quill. Apparently dust from turning wet wood had gotten between the quill and bore causing fine deposits of rust. I lubed the threads with WD 40 and the bore with graphite powder. I am paying attention to how much effort it takes to operate the handwheel. Thanks for all the great videos.
Thank you, Mike. I didn’t really find it intimidating but it took me a few minutes to figure out how to take it apart. After that it was fairly easy. Now I have to remember to do it frequently and to try some of the other lubricants that have been suggested. Hope you’re doing well, Mike. Take care, .....Gord
I’m not sure if it’s a good thing or not but my wife likes to help clean up the shop. Of course once she finishes I can’t find anything for a few days but I’m not brave enough to tell SWMBO not to help! 😳😳😳😳 Take care my friend, .....Gord
Gord, I also have a DVR XP, and had the same issue last year with a sticking tail stock. If I may suggest, do a follow up video showing how to clean the gunk off the bottom plate of the tail stock, and if you are adventurous, show how to align the tail stock with the head stock.
Doug, I don’t have any “gunk” on the bottom of my tailstock. Maybe I’m just lucky but that’s never been a problem for me. As far as aligning the tailstock, there is a bit of play in my tailstock as it rides on the bed ways. It’s very minor but still the only thing on the lathe that I’m not totally happy with. I’ve been told that the newer ones don’t have that problem. It’s something that I have learned to deal with but I don’t think I would be able to properly explain how to align it with mine not performing perfectly. Thanks for watching and for your input. Take care, .....Gord
wd is good but ether of these 2 are better WD-40® SPECIALIST® PROTECTIVE WHITE LITHIUM GREASE WD-40® SPECIALIST® DIRT & DUST RESISTANT DRY LUBE PTFE SPRAY the dry lube is what i use
Gord, I agree with Kevin. WD-40 was never designed as a lubricant -- the "WD" stands for Water Displacement. Formula number 40, to be complete :-) I too use a dry lube with Teflon, a 3M product (don't remember the name, it's down in the shop, & I'm lazy...) that I first started using to lubricate motorcycle chains. Now it's my go to lubricant. Clyde