Making a Foam Space Helmet: Part 1 / Pattern

Подписаться 193 тыс.

Просмотров 15 тыс.

50% 1

Making a Foam Space Helmet: Part 1.
I'm very proud of this build, and happy to finally make these patterns available to you. This one of the most elaborate patterns I have done for my shop.
Chapters:
01:21 Step 1 & 2
04:37 Step 3
05:38 Bandsaw
06:21 Heat shaping
08:33 Gluing neck ring
09:14 Step 25
12:53 Step 23
14:25 Step 4
15:07 Step 5
15:35 Step 6
17:09 Step 7
18:34 Step 8
19:31 Step 9
19:46 Step 10
20:14 Step 11
20:34 Step 12
21:07 Step 13
21:50 Gluing Neck to Collar
25:01 Step 14
26:56 Step 22
30:07 Step 15
30:24 Step 16
31:19 Step 17 & 18
32:37 Step 19 & 20
34:58 Step 21
34:20 Step24
36:34 Placing magnets
37:28 Gluing magnet
39:46 Gap-Filla
40:37 Masking magnets
41:34 Sealing with Creature cast rubber
Space Helmet Pattern
eviltedsmith.com/shop/space-h...
Small to Med clear visor.
bit.ly/3LZbtOJ
Adam's New Space Helmet from Evil Ted
• Adam's New Foam Space ...
Space Wars the quest for Deepstar trailer
• SPACE WARS THE QUEST F...
My build list.
Cosplay Pros Foam
thecosplaypros.com/?ref=pdyq8g01
WTF foam
amzn.to/3hcoi7Z
Uni-ball white gel pen
amzn.to/3IvBsJ6
Cutting mat
amzn.to/3CtAIAz
Heat gun
amzn.to/3kIGLKM
Three inch Acrylic dome
amzn.to/3D5W4I1
DAP weldwood contact cement
amzn.to/3hg1sfO
Glue pot
amzn.to/3dNLGrZ
Straight pins
amzn.to/42qe35D
Craft knife.
amzn.to/1pSKlDI
Craft knife blade pack.
amzn.to/2EafACJ
Utility knife
amzn.to/3kPiUKk
Blade sharpener
amzn.to/3lb3gcv
WTFoam 2mm
amzn.to/3Tj8NMG
Rotary Tool
amzn.to/2JdN2fi
Flex shaft
amzn.to/37LQtGI
Sanding drum
amzn.to/3dlvxbq
Stone bits
amzn.to/3HAbfJx
Cutting wheel
amzn.to/3NCylET
Sanding sticks
amzn.to/418GRyy
Clear ruler
amzn.to/3NEYz9C
Metal ruler
amzn.to/3VAYypb
Brass tubbing
amzn.to/44t6Gw6
Wood burner
amzn.to/3AZebgN
Earth magnets
amzn.to/3AUC74L
Goop glue
amzn.to/3LYxBbG
Metal spatula
amzn.to/3DSHUIy
Gap-Filla
www.propmonkeystudio.com/produ...
Frog tape
amzn.to/3pbqtQw
Spray gun
amzn.to/3tptETh
Surebonder battery powered glue gun
amzn.to/3Hf3W8F
Creature cast rubber
creaturecastrubber.com/new-pr...
If your new to cosplay, you should Join the Foam Fanatics.
A great friendly group of fellow makers that are there to help.
Be sure to answer the two questions before joining.
/ evilt. .
My website eviltedsmith.com
Twitch / eviltedsmith
Facebook / eviltedsmith
Instagram / evilted_cha. .

Хобби

Опубликовано:

5 май 2023

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 52

@BongoWongoOG Год назад

Nice build Ted. that helmet pattern of yours is pretty universal. Slight tweaks and its applicable to a whole host of uses from centurion to knight to space alien. Truly evergreen.

@EvilTedSmith Год назад

Thank you.

@andybogart2503 Год назад

It’s cool to see your techniques and product preferences evolve over time. You’re awesome Ted!!

@EvilTedSmith Год назад

Thank you. You never stop learning.

@theamazinggoldfish8713 Год назад

Looks like something from the old tv show "Space 1999". Not that im that old or have seen that show in anything but reruns 😂.

@EvilTedSmith Год назад

Well I'am that old! Loved the show when I saw in my teens. Thats why I painted the helmet orange.

@tomruotsalainen5909 5 месяцев назад

Space 1999 helmet was yellow Anyways do you have a pattern for the foam cut outs or any measurements?

@oculus1857 Год назад

Space Helmets for the masses ❤

@EvilTedSmith Год назад

Yes, for everyone.

@jamesnealy3750 Год назад

I was on when you started the skull build. That inspired me to build my own skull last Halloween.

@EvilTedSmith Год назад

Well done!

@garthmccarthy4911 Год назад

I can't wait for this. I have been struggling to come up with a space helmet design for a no budget Sci-fi film I am working on and I hope this will be of some help :D

@EvilTedSmith Год назад

I'm sure this with solve your problems. So happy with this pattern. I took a while to get it were I could post it.

@garthmccarthy4911 Год назад

@@EvilTedSmith thank, I'll make a few changes, just so it's not exactly the same as the one in Space Wars

@tobynobel5671 Год назад

Love space helmets!

@EvilTedSmith Год назад

Me too!

@zns72 Год назад

Love the new opening!!!!!

@EvilTedSmith Год назад

Thank you so much. It was long over due!

@goldensketch8321 Год назад

I think I'm going to use this pattern for my HEV Suit cosplay! (that I'm eventually going to make, lol!) Thank you for posting this wonderful video :]

@EvilTedSmith Год назад

Thank you for watching and subscribing.

@ajkohkoh3921 Год назад

I’ve been looking everywhere including your website for a good helmet with a neck ring that I’m able to attach to my suit to the point where I currently have someone 3d printing it for me

@EvilTedSmith Год назад

You're wait is over the pattern is now available in my shop. eviltedsmith.com/shop/space-helmet/

@seanhoude Год назад

I alternate polarities, so there's only one right way for parts to hold together.

@itsagundam79 Год назад

I imagine this works really well for left and right parts, or when you have to put multiples of spikes or other trim onto a costume. Make sure they all sit in the right areas at the right angles. Great tip!

@storylitfilms 4 месяца назад

Hey Ted! Thanks for sharing this build! I'd love to try this but am curious a bit more about the first steps. If I purchase the build pattern is it possible to print it from a standard printer, printing on 8 1/2 by 11 paper and get the right measurements? I'm just curious about those first few steps.

@EvilTedSmith 3 месяца назад

Yes, you can print them on a stander printer.

@nickdavis5420 Год назад

It reminds me so much of alien that industrial look . I have been rewatching your vampire hunter d stuff as my message from mars kickstart stuff shipped great comic unfortunately a case of the variable sword length.

@itsagundam79 Год назад

This is such perfection. I can't wait to get started on this! Knew I needed 8mm foam for something, still gotta pick that up. I noticed when you are doing the flat edges of the bottom of the helmet and top of the neck collar, you have to Dremel them down for the flatness to lay on the neck ring. Can you just do the initial cuts at an angle over those areas to simplify it? Or is the angle so miniscule it's not worth it to try? I have a tool called Bev-All that let's me select popular increments of cut angle like 90°, 45°, & down to 22° I think.

@EvilTedSmith Год назад

Yeah that should work. Let me know how it turns out.