Making a Mini Hydraulic Pump 

What a nice little tip that is with using the circlip in the lathe chuck to locate the piece for machining. I'm going to have to buy a selection of circlips now!

I've been around lathes, mills and other workshop kit for nearly my whole life and I've never seen that circlip trick before. It's fantastic. I love it. It's so simple. I will definitely use it sometime soon. Regards Mark in the UK

Читаю коментарии и виду что весь акцент направлен на стопорное кольцо. Я думал что я один из не многих кто незнал этот лайфхак. А оказалось таких как я достаточно. Я тоже за все время просмотра ютуба впервые такое увидел. Никто так не делал, хотя наверняка есть такие люди. Сейчас думаю во многих роликах это будет показано так как многие друг у друга набираются опыта. Я тоже обязательно этим воспользуюсь. Спасибо автор.

Лайфхак с кольцом в патроне, в который упирается деталь, просто зачет 👍

The circlip idea was awesome!

Use of circlip for positioning of part in lathe, is a amazing idea😮

Использовать стопорное кольцо прикольно придумано👍👍👍👍

Very nice. Your pump has no ball bearings, so don't apply radial force to the axis with that chain / gear. Use direct coupling to the motor.

Interesting way to register your work, quick and dirty. I'LL have to try it out.

Nice build but you need much much higher precision if the pump shall give more pressure than a couple of bar. My powersteering pump is of the same type and when it failed I bought a new one but I took the old one apart of curiosity. I couldn't even see any scratches but it had lost pressure anyway. The wings need to be very tight in the hub and the inside of the housing needs to be ground and polished. The smallest gap or scratch and the pressure is lost.

Everything was fine, only if you had touched the contact surface of the aluminum parts (5 pics) with the inside of the main part, the pumping power would have been much higher. That is, you would level the parts with the inner radius of the cylinder. I hope I got my point across❤

Nice build. That is basically the exact same idea in most every pneumatic hand rotary tool as well. Except they use vanes from non-metallic materials so they seal better and wear less... When those tools start loosing power, you replace the vanes and you are back in business... Thumbs Up!

Автор молодец, спасибо за совет тоже буду пользоваться стопорным колечком для базирования детали в токарном патроне👍

Using the circlip was new to me I will have to get a set Thank you

Idea Is awesome. But, ek hydrolic pressure banane ke liye 20 hazar mobile kon tut ta ?

Making something like this is very hard. You are a skilled person ❤

Reminds me of the time I invented this very pump design back around ~1985 only to find out a few years later it had already been invented a long time prior and in wide spread use. I find it amazing how the same things can be thought up by many different people over time.

В насосы такого типа не ставят пружины под лопатки, они работают за счёт центробежной силы. Меньше трения на лопатки, более свободный ход.

I really hope you sent this to the phone manufacturer. Lol. However, I will be using this to help me design a few things. Thanks, Brother!

have you messured the pressure the pump is able to generate?

what determined where the inlet and outlet go as i would have thoungt the most open portion of the pump and the most closed

I like the design especially when impeller is so simple but i was thinking with your use of springs, if the impeller was spinning at a high RPM would it still get a good seal as the fins be thrown out towards the side of the case similar to an pneumatic motor.

It looks like a pretty good hydraulic pump you're using your time for something really worthwhile

Thanks you. I got concept of hydraulic pump 🙏

Adorable little vane pump. Well done.

The test subject was a tough one.😅😅😅 Nice build.

You have great ideas. Thanks

Awesome. You should definetly buy a mini mill.

a smart and professional job👏😍

sehr schon perfect vielen dank fur tecknik du gut machen arbaiten dugute

You are very smart and skilled 😍

Great content! Keep going

Nice skills friend

Convert your lathe to a horizontal mill for your slots..

I didn't know that trick to center pieces on a lathe... and I work in a workshop of lathe... thanks for the video.

Chăm chú xem đến cuối cùng lại đi phá hư cái điện thoại, vậy lấy cái búa bụp cái là xong cần chi mất thời gian quá.

Молодчина! Руки с правильного места растут и голова работает!

Excellent pump.

Very informative thank you ❤❤❤

Well done But there is another way to get more accuracy when putting those piece in the lathe I blotted some aluminum rod in between the jaws, and when I go to use it without the jaws in place, I machine face it, they are removable, And if he did not have a mill He could have held that center piece on the carriage on the lathe and used a milling bit or even a drill bit to cut a real perfect slots .

I agree i have a selection of snap rings or circlips I’ve never seen that before I’m trying this thanks

Incredible, very skilled and talented to make your own rotary vane pump, gives me inspiration to make one. Would be nice if you can make a 2 stage vacuum pump. 10:14 - Is this a mechanical seal? Where can I get one? thanks.

Oh hey thanks for the video. I'm cloning some dry sump stages for my engine build, stumbled across this! Nice to see you having fun fabricating. Thanks for the vid!

Hello, I really liked your video, what is the name of that type of anti-gas bearings?

Love the fact you flew clean past the tolerances for the vanes, and installed the oil seal backwards. You can always figure out which side is the side that fluid is supposed to be on by the easier of the 2 ways to install a seal on a shaft. Lip always faces higher pressure.. 😂

Hola donde puedo encontrar planos de la bomba hidráulica

Interesting😉

what is that piano wire in a coping saw? great build btw.

What's your top pressure?

For an vacuum pump (desoldering tool) I've seen a similar design but using graphite (carbon) vanes.

Creative video, thanks :)

Super pompa , ingenioasă fabricarea ei, dar pâcat de telefon.

بسیار خوب❤❤❤

Fun project, nicely done

Awesome 👍

You made everything up to the plastic hub/bearing in the end. Just wondering why you did not also make that since you did everything else. I mill would make many of the things you did a bit easier and precise, but good job using the tools you had.

Now you need to make a couple drive motors so you can make your own lawnmower.

Très bonne idée d utiliser le cervlips merci pour ton idée

This hydraulic pump will definitely work. It is a well known one, but because of materials used and the lack of surface treatment of the pump house, it is just a matter of time until the hydraulic system will be damaged, because of the small aluminium shavings.

it looks like you put the shaft seal in backward at the end, the side with the little spring is supposed to face the pressure.

amazing 😍👌

Phót bơm thủy lực..mua rẻ ơi là rẻ.. tự làm ra mỗi cái.. tính theo giờ.. có thể mua năm mười cái..xịn .. bền tốt..hi...hi...

Impresionante es una bomba de verdad se puede subir agua a un tanque con un diseno mas grande gracias Argent

It was interesting❤❤

Could you provide a print for the pump

Gut gemacht 👌

Чувак с лобзиком ты здорово придумал 😅

świetnie to wykonałeś moje gratulacje 👍👍👍

what that phone ever do to you?

Дуже круто,єдине що незрозуміло- навіщо телефон зламав?

Күшті насос екен уйге қажет май құйған ға

Very good

Where is the bearings???😊😊😊

Nice 👍🏻

Can I have the work plan please

I would love to do that to my cel as well!lol

Good boy

Só pelo anel elástico como stop já valeu 1000 like

Das gefällt mir super 😍

Not much good for hydraulic pump but would make excellent suds pump for lathe coolent!.

Das schon berawo❤❤❤❤❤

Nice 👍🎉😂 یه چه مسخره بازیه فندکمه بیار 😂😂😂😅

❤ sao mà hay quá dị.

Nice work but I don´t recommend to wear gloves of any kind.

Very nice 😂

Please bulid hydraulick motor

Probably cheaper to buy a pump rather then buying a lathe, mill and all the rest to make to pump... :D :D

Top

Насчёт стопорного кольца это хорошая идея, а вот зачем смартфон ломать... непонятно.

So freaking cool men

Теперь я знаю как разобрать мобильный телефон))

Motor quay 5 lá sắt tự văng ra chứ cần gì phải lò xo

Перекачивать воду из емкости в емкость пойет, но не для создания высокого давления.

الان آخرشه دییم یه گوشی مه قورتنیش د یک اینارو دیگه مترجمم نمیتونه ترجمه کنه😂

Насосы с таким принципом работы используются в автоматах газводы. Они итальянские, стоят под 300 баксов. Могут делать давление 15 атмосфер. Правда у них полость из пластика и стираются они быстро. Этот навряд ли сможет создать высокое давление

hi friend

Oilseal is backwards.

👍👍👍👍

Hay lắm

noooo el telefono ,amigo esta bien lo que iste y me impresiono pero el telefono no ,si👍