Тёмный

Making a semi-hollow neck-through winter bass guitar 

lignum
Подписаться 335 тыс.
Просмотров 367 тыс.
50% 1

The second guitar in the four seasons series :) This time it's a necktrough semi hollow design made from maple and smoked oak veneer. The theme is winter so we took a snowflake and white color as main motifs in this build. It took quite some time to get the design right but after couple of work days the 3d model was complete and we could start the production. The 5cm plank was first cut to desired smaller pieces. each piece was than planed 43mm thickness and glued together into a single block. Glue we used for this project was vinyl acetate based with short open time of 20 minutes. After the glue has cured, the block was left for a week to relieve some possible inner tensions and to achieve uniform moisture level troughout the cross section. The block and the fret board was milled on kuka kr 150 industrial robot. Tension rod is made from two 4mm round cold rolled steel rods, one 4mm inbus screw and eight 4mm nuts. Fret slots were marked with a blade over the paper with precisely printed fret positions and then cut with a small hand saw. After the fret board was glued onto the neck over the truss rod groove and all the necessary holes were drilled, the guitar was sanded and prepped for painting and six coats of varnish. Fret board was oiled with teak tree oil and frets were hammered and then pressed into their designated grooves. Schaller tuning keys and piezo bridge were the choice for this build so after we installed them, it was time for electronics. A good friend of my brothers, Phd student Ante Brizić made schematics for this guitars electronics which we build for only 5 dollars or so.. And it works great! After all the soldering, it was time to put the whole thing together, add a guitar belt, tune the strings an done! This project took us well over 150 work hours.
Special thanks to Schaller for all the advice about piezo bridge instalation and also to Krešimir Klen- Fish for the final guitar test!.. :D!
Thank you for watching and don't forget to like and subscribe! :D
My instagram: lignum_chan...
My facebook: / lignumchannel
Website: www.lignum-art.com/
Music:Earle_s_Bar_Room_Rocker, Jack_s_Garage, Slow_Times_Over_Here, Sunny_Looks_Good_on_You, Take_Me_to_the_Depths by Midnight North

Хобби

Опубликовано:

 

11 фев 2020

Поделиться:

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист
Посмотреть позже
Комментарии : 465   
@Jordan_C_Wilde
@Jordan_C_Wilde 4 года назад
You didn't really just make your own circuit board ... "How f*ckn extra do you want your guitar Sir ?" "Yes." Absolutely incredible.
@lendljohndarlo9339
@lendljohndarlo9339 3 года назад
Omg!
@ibnzain
@ibnzain 3 года назад
that's a bass, not guitar
@Jordan_C_Wilde
@Jordan_C_Wilde 3 года назад
@@ibnzain it's a bass guitar
@egmccann
@egmccann 4 года назад
Don't think I"ve seen anyone making a truss rod. Interesting.
@d1sord3r
@d1sord3r 4 года назад
Personally, I wouldn't trust those welds on the rod. There ain't much weld penetration happening and it is crucial to the strength of a welded connection. Doing it like that on an easily accessible part - I don't mind that; having it in a neck of my guitar, under constant tension - not so much. I'd rather do it with a tig torch or figure a way to do it without welding the rod itself, but that's just me. Still, a very cool and unique guitar.
@Timopeo
@Timopeo 4 года назад
@@d1sord3r i make one for a 5 string bass, i welded it with mig and spot welding, and is still working
@jeffreycollins7297
@jeffreycollins7297 3 года назад
And a whole active system too. These guys can literally made a guitar from the ground up. Only thing they didn't make were the bridge and tuners. DAMN!
@ff-qf1th
@ff-qf1th 3 года назад
@@Timopeo huh! well fancy that. I'll have to try that some day
@Galova
@Galova 3 года назад
I know a luthier that makes truss rods himself always. And when I asked him why he laughed saying that it's same thing as factory made and cost fair just as much as factory made truss rods should cost - something about nothing. He said that he's never seen that his hand made truss rods ever broke.
@jeffhiggins4478
@jeffhiggins4478 4 года назад
That’s the most beautiful headstock I’ve seen in a looooong time.
@msmith2961
@msmith2961 4 года назад
Never did I think I'd see PCB transfer and etching on your channel! Amazing work (as always), and well worth the 150 hours!
@cheezitmaster2312
@cheezitmaster2312 4 года назад
Most actual guitar manufacturers don’t make their own truss rods. What a mad lad
@KnaGGelMan
@KnaGGelMan 4 года назад
A fretless version of it would be totally awesome.
@tomek9966
@tomek9966 4 года назад
If not better than awesome ;)
@NobodyAwsum
@NobodyAwsum 4 года назад
Dude. I hadnt even thought of that. Its be better.
@jeffreycollins7297
@jeffreycollins7297 3 года назад
Yeah it'd be kinda like a Michael Manring Hyperbass..
@MonsieurMaskedMan
@MonsieurMaskedMan 2 года назад
it would be like those infinite fretboard bass like Jens Ritter, Algan, and Stradi
@samk8005
@samk8005 4 года назад
This whole thing was amazing, but after seeing years of woodwork on your channel, the thing that blew my mind was making the circuit board. So cool.
@michaelolz
@michaelolz Год назад
I don’t normally say stuff like this nor do I go in for instruments that look too fancy. But this made me tear up a bit. I think it’s the nicest design in a bass guitar I’ve ever seen-a true bucket list instrument.
@MythixMusic1
@MythixMusic1 5 месяцев назад
So much to love about this design! Seeing you make your own circuit board blew me away too
@MarcBeland
@MarcBeland Год назад
Build your own truss-rod?? Etch and build your own circuit board?? Edge-mounted controls for that simple yet elegant look?? OUTSTANDING!!!
@genekloszewski4526
@genekloszewski4526 4 года назад
absolutely,.. historic build !, super talented, when i saw you etch your own board, i knew we had a live one here !
@pwhite102
@pwhite102 4 года назад
the mix of machines and hand tooling is very cool
@jeffreycollins7297
@jeffreycollins7297 3 года назад
I think i'm on number three or four of watching this. Each time I am still amazed. Never gets tiring. Only wish I had one for myself.
@lignumchannel
@lignumchannel 3 года назад
😁thank you so much Jeffrey! I'm glad you like it so much!
@MCBWoodworks
@MCBWoodworks 4 года назад
That is amazing! Your range of work and skill set is impressive.
@trotski310
@trotski310 4 года назад
Truly amazing! I was mesmerized the entire video
@heatherscanlan5016
@heatherscanlan5016 4 года назад
I love this, beautiful design and finish. Also excellent unconventional use of drill “press”! Amazing
@karl_alan
@karl_alan 4 года назад
I love the mix of techniques and styles in this project. Definitely masterful work and amazingly thought out design process.
@lignumchannel
@lignumchannel 4 года назад
Thank you very much Karl! :)
@tylerthompson1842
@tylerthompson1842 2 года назад
That CNC router is badass. Guitar came out perfect.. got serious thump in the low end. I imagine that body style is really good for overall neck strength, alignment, and acoustic resonance.
@teedub127
@teedub127 3 года назад
What an awesome build, from start to finish! Thanks
@franciscotamez7203
@franciscotamez7203 4 года назад
Ok. In English. I've played as a bass guitarist in several Rock bands. After watching these videos, now I feel more respectful towards my bass guitar.
@bass_covers
@bass_covers 3 года назад
Could watch that for hours ! Great !
@geraldanderson7576
@geraldanderson7576 4 года назад
Absolutely gorgeous instrument!
@CNCChazz
@CNCChazz 4 года назад
Wow that was an amazing build to watch, very inspiring thanks for sharing
@KhellendrosXS
@KhellendrosXS 4 года назад
Two words: Simply amazing!
@lignumchannel
@lignumchannel 4 года назад
Thank you Chris :D
@andrewturnbull5897
@andrewturnbull5897 2 года назад
A stunning instrument! Elegantly executed! Thank you for sharing!
@Doohickeydongle
@Doohickeydongle 4 года назад
Beautiful bass. Love the blending of modern and classical aesthetics. Not many could pull that off and not look gimmicky. Excellent work.
@lignumchannel
@lignumchannel 4 года назад
I'm glad you like it Jeff! :D
@junh4100
@junh4100 4 года назад
This bass guitar is just beautiful and divine.
@rayerscarpensael2300
@rayerscarpensael2300 4 года назад
What a bunch of tools you own and master... unbelievable. You can make anything.
@StanCrafted
@StanCrafted 4 года назад
Looking so good...can't wait for Spring and Summer!
@lignumchannel
@lignumchannel 4 года назад
Me too.. Thx:)
@AZMC
@AZMC 4 года назад
Your work and videos are very cool and helpful. Thank you for the wonderful work.
@ОлегГриднев
@ОлегГриднев 4 года назад
Да, с таким оборудованием можно делать шедевры, что и было сделано. Молодцы!
@lignumchannel
@lignumchannel 4 года назад
я рада что тебе нравиться! :D
@oakleyjack7600
@oakleyjack7600 4 года назад
You are a Artisan, the machines cannot perform without input and the chisel cannot guide itself. 👍😎🎩❤️
@lignumchannel
@lignumchannel 4 года назад
Thank you:)
@danielvandoorn
@danielvandoorn 4 года назад
Love the placement of the tone and volume control. Beautiful guitar!
@jeffreycollins7297
@jeffreycollins7297 3 года назад
Theres a luthier in Columbus Ohio named FRENZ that has been doing that on basses since the mid 90's. It's really friggin cool.
@skalewilly
@skalewilly 4 года назад
Fantastic, great job!!! congrats!!!
@rhart367
@rhart367 4 года назад
This video was awesome. What a beautiful bass guitar. Wow! You guys kicked @$$ on this one. Bravo. Stay blessed.
@dorianchriste8645
@dorianchriste8645 4 года назад
Wow! That was a joy to watch! This bass is art!
@ellieboa
@ellieboa 4 года назад
Killing it as always! Absolutely gorgeous
@lignumchannel
@lignumchannel 4 года назад
Thank you Ellie! :D
@BurtonsAttic
@BurtonsAttic 4 года назад
You guys are getting it done, and it has a great tone! Enjoyed watching
@richsackett3423
@richsackett3423 3 года назад
You think so?
@FromTheHeartWoodMK
@FromTheHeartWoodMK 4 года назад
A fantastic edition to the collection! Now you really can't go back, you must finish them all! I love everything about this guitar, it perfectly and essentially SCREAMS Winter. It's cold and calm, yet beautiful and mysterious at the same time. Love it, 5 out of 5 for me, I'd give you 6 or 7 if I could!
@lignumchannel
@lignumchannel 4 года назад
:D thank you very much! I really have no other choice now, I hope you'l like the rest too..
@ESPecialEntertainment
@ESPecialEntertainment 4 года назад
Beautiful piece of art!
@captivenut4122
@captivenut4122 4 года назад
Amazing! Always a pleasure to watch an artist at work!
@lignumchannel
@lignumchannel 4 года назад
:D I'm glad you like it!
@timberdish
@timberdish 4 года назад
Most excellent indeed my friend! Very tasteful shape with some really stylish touches. Loved watching that, as always. Thanks for sharing! :D
@lignumchannel
@lignumchannel 4 года назад
Thank you for watching Matt! I'm glad you like the design!
@natalieivey23
@natalieivey23 4 года назад
I really like the cello-esque design!
@Musicman914
@Musicman914 4 года назад
A thing of beauty.
@steve647my
@steve647my 4 года назад
Only one word can describe it. FANTASTIC!!! The tone and sounds were perfect and so pleasing to the ear. That is one of the best sounding guitars I have heard in a long time.
@lignumchannel
@lignumchannel 4 года назад
Thank you Steve! I will make a sound demo video sometime in the future with better sound recording equipment, camera mic is just not good enough..
@steve647my
@steve647my 4 года назад
Make it a good one
@joschkawiencke8413
@joschkawiencke8413 4 года назад
Beautiful as always!!
@lignumchannel
@lignumchannel 4 года назад
Thank you Joschka! :)
@geologist_luna
@geologist_luna 3 года назад
I can't even express how excited I am to see the idea of inset pots! Fantastic build!
@lignumchannel
@lignumchannel 3 года назад
Glad you like it Antonio!
@handmadeisbetter
@handmadeisbetter 4 года назад
Is there a thing you can't build?? Seriously, great work! Amazing!
@wayneeverett8357
@wayneeverett8357 4 года назад
I have a White electric twelve string and it looks GOOD like this !! Great job !
@johnmoser2689
@johnmoser2689 4 года назад
Totally worth the watch soooo cool
@Grandpaplaysbass
@Grandpaplaysbass 4 года назад
My God I loved watching that!
@M4DHUSKY
@M4DHUSKY 4 года назад
Wo-hoooo, almoust 18min video, thank you majstore 😀
@lignumchannel
@lignumchannel 4 года назад
:D pre dugo ako se mene pita..
@DMDvideo10
@DMDvideo10 3 года назад
That is a work of art!
@trukr817
@trukr817 4 года назад
Super nice! Well done.
@eldernascimento287
@eldernascimento287 4 года назад
it takes so many machines to make handmade bass.
@garcj108
@garcj108 4 года назад
fantastic as always!
@lignumchannel
@lignumchannel 4 года назад
Thank you Libo!
@ishita4179
@ishita4179 4 года назад
Omg I love winter and this is so satisfying to see!! Now I want this guitar😭. But seriously this was a good freakin job and such a creative idea! 💕💕
@lignumchannel
@lignumchannel 4 года назад
Thank you Ishita!
@heinavaara113
@heinavaara113 3 года назад
That sounds nice!
@NKBobcat
@NKBobcat 4 года назад
A great way to spend 17:49 of my life. Fantastic work!
@technewsfortechnoobs
@technewsfortechnoobs 4 года назад
And to think I found this video on my birthday!! I would absolutely commission a bass like this with a few cosmetic modifications.
@designersmind3140
@designersmind3140 3 года назад
Incredibly beautiful visual design. I would love to hear a longer clip of it being played by a pro bassist
@todhollo1961
@todhollo1961 4 года назад
cool idea to put knobs in the side of body, great work
@normg2242
@normg2242 4 года назад
A swan of a bass...!
@danielmontano5955
@danielmontano5955 4 года назад
Madreeeee míaaaaa!!!! Ha quedado genial!
@adraanarchy5888
@adraanarchy5888 4 года назад
Absolutely gorgeous...
@lignumchannel
@lignumchannel 4 года назад
Thank you! :)
@emax7900
@emax7900 4 года назад
Wonderful!
@TheWind213
@TheWind213 3 года назад
Beautiful, I enjoyed watching you build your bass.
@lignumchannel
@lignumchannel 3 года назад
Thank you very much!
@super60d
@super60d 3 года назад
Masterpiece !
@lignumchannel
@lignumchannel 3 года назад
Glad you like it Marc!
@MrFrkbass
@MrFrkbass 3 года назад
Amazing
@ConstantXplorer
@ConstantXplorer 4 года назад
Fantastic
@rootvalue
@rootvalue 4 года назад
Everything about this is perfect, right down to the Hipshot hardware. Masterful blend of machine and hand tool production.
@LopezDeLaGuerra
@LopezDeLaGuerra 4 года назад
The hardware is actually Schaller. But still so perfect. :]
@rootvalue
@rootvalue 4 года назад
LopezDeLaGuerra you’re right! Good eye.
@philiphurdwell3443
@philiphurdwell3443 4 года назад
Stunning....
@lignumchannel
@lignumchannel 4 года назад
Glad you like it Philip!
@johnniewalker39
@johnniewalker39 4 года назад
Amazing!
@lignumchannel
@lignumchannel 4 года назад
Thank you!
@shunthecaveatofficial
@shunthecaveatofficial 4 года назад
The truss rod specifically is the most wild thing I've seen in the whole RU-vid guitar making world. This is a beautiful video and product man.
@itonuoro3813
@itonuoro3813 2 года назад
awesome!
@troyclayton
@troyclayton 4 года назад
Really wonderful. You might consider using machine screws (and threaded inserts) to hold the back plate on. I loved that touch on my old Alembic.
@danieldudas9026
@danieldudas9026 4 года назад
Was waiting for the "semi hollow neck". Still not disappointed.
@kmasfalto
@kmasfalto 4 года назад
Ficou com um som muito bom !!
@ProfDrMau
@ProfDrMau 4 года назад
Well, i am new to this Channel. And just as i thought ive seen every carpentry equipment possible, this guy casually starts one of his two(!) one armed Robots. Nontheless an amazing build :D
@vladimiryan1335
@vladimiryan1335 4 года назад
Весь ролик напрягался, боясь что что-то пойдет не так. Однако, результат выше всяких похвал!
@lendljohndarlo9339
@lendljohndarlo9339 3 года назад
The man even can slap!! Very talented bass maker guys.. Who here are fan of slappin Davie504?
@DaskaiserreichNet78
@DaskaiserreichNet78 4 года назад
Awesome looking bass. I was surprised to see him cut the fret slots freehand without any guides after seeing the robots carve out the body.
@djaffarsaid483
@djaffarsaid483 3 года назад
Bravo pour se grande travaille
@ff-qf1th
@ff-qf1th 3 года назад
Wow! what a cool looking bass! Also, I love the idea of putting the controls on the side of the guitar rather than the top- I'll have to steal that idea for my own build! :)
@vlad877
@vlad877 4 года назад
Молодчик, гитара просто произведение искусств!!!
@farazzaidi944
@farazzaidi944 4 года назад
Making the truss rod and volume and tone control board was my fav part!
@wakjoko997
@wakjoko997 3 года назад
Awesome 👍
@lignumchannel
@lignumchannel 3 года назад
Glad you like it!😁
@ludoviclebouhoulec2556
@ludoviclebouhoulec2556 4 года назад
De toute beauté cette basse félicitations à son créateur
@stavrospapadimitriou7631
@stavrospapadimitriou7631 4 года назад
I think I'll go out tomorrow, buy a Dremel, and make one of these for myself...
@lukesmale123
@lukesmale123 4 года назад
Wow I want that!
@GalleryBones
@GalleryBones 4 года назад
Amazing video, more like it please !!!
@lignumchannel
@lignumchannel 4 года назад
Thank you Simon!
@Declare57
@Declare57 4 года назад
You should be proud of this beauty! mm mm, good!
@gelloyangsteryang6481
@gelloyangsteryang6481 4 года назад
autumn done!! winter done!! summer left!
@johnconklin9039
@johnconklin9039 4 года назад
Very cool! Making guitars is no joke, much more to it than people think.
@ragnkja
@ragnkja 4 года назад
John Conklin I suppose electric guitars are a bit easier to build than acoustic ones, but given how specialised a craft luthiers practice, it’s definitely no joke. After all, the maker still needs to do all the same things except for the sound box.
@waltermorales5939
@waltermorales5939 4 года назад
beautiful bass
@lignumchannel
@lignumchannel 4 года назад
Thank you Walter :D
@waltermorales5939
@waltermorales5939 4 года назад
your welcome
@creyuss1983
@creyuss1983 4 года назад
Awesome
@E6963
@E6963 3 года назад
Muito louco ! 👏🏻👏🏻✌🏻
@XXX18343
@XXX18343 3 года назад
pleaseeeeeee, keep making guitars!!!!!!!! u guys are amazing!!!!!!
@smokinvalves
@smokinvalves 4 года назад
Nice build. Can't go wrong with the Powerfix range - incredible price for the quality.
@johnnydeformed7123
@johnnydeformed7123 4 года назад
Where are the pickups? I assume some sort of piezo somewhere, but I can't find the part of the video where they're installed. Amazing job, though. Looks beautiful.
@LeglessWonder
@LeglessWonder 4 года назад
Was wondering the same thing. Would like to know how it works
@nourel-deenayman3943
@nourel-deenayman3943 4 года назад
Cody Evans probably built straight into the bridge
@andrewgocken517
@andrewgocken517 4 года назад
@@nourel-deenayman3943 seems many basses of this style, have those. Interesting concept.
@themadcow8191
@themadcow8191 4 года назад
They're built into the bridge! If you look at 13:00 where the bridge is installed, you can see the wires from the piezo pickups being run through the body. Each bridge saddle has a separate pickup in it, and each string runs over a tiny piece of metal in the saddle that transfers the string's vibrations.
Далее
Making a Summer Night Bass - Full Build
16:54
Просмотров 577 тыс.
I made relic BASS GUITAR from scratch | Guitar build
19:48
Making A Custom Guitar From Scratch
19:33
Просмотров 596 тыс.
Making an electric autumn guitar - robot project
15:15
Просмотров 620 тыс.
Building a 7-String Guitar Using Hand Tools
30:14
Просмотров 16 тыс.
ПОДВОДКА ДЛЯ 6 ЛЕТ💅💄
0:20
Просмотров 2,3 млн
Жалко Кирилла? #юмор #шутка
1:00