Thanks for all that you share here... it’s so helpful. I’m a student metalsmith and I recently began to wonder how to make a stamped bezel and how to deal with the resulting distortion of the thin metal. I see it’s as simple as getting out the draw tongs, and using a vise. Brilliant! It feels like this technique is now within my grasp 👍🏼
Very nice video. Soothingly informative. Creating jewellery is awesome. I work on computers all day long, and get little satisfaction out of it, but when I go to my shop after dinner and start working with cabs and silver... I feel like I'm doing something!
just fabulous watching the hands of a craftsman, i'm no where near your skill level, but i really enjoyed watching the construction of that beautiful piece. With no talking over it i could reallh concentrate on what you were actually doing. Thank you.
I just came across your channel. I must say I haven't seen jewellery tutorials like yours before. I guess they are not for complete beginners but that's ok because there is plenty of those out there anyway. You also cover techniques and scenarios I haven't seen covered anywhere else. Great skills. Also - watching you work in that calm and confident manner joined with this slightly trippy music is extremely relaxing and peaceful! :) Double effect! Thank you for taking the time to make these!
Thank you very much for the positive review! I set out to make videos that might be enjoyed by makers of beginning to intermediate skill levels. Thanks for taking the time to comment. Are you a maker?
I would say I am a maker, yes. But I am just beginning. Beginner/intermediate. :) I had to go to school to obtain certification - this is a legal requirement where I live so I guess I have some formal education too. But the more I know the more I realize how little I know. :D Goldsmithing/silversmithing covers incredible variety of techniques and materials. Love it! :)
I must say I have found a favourite jewellery making RU-vid channel. I love how you do all the work and it’s clearly visible but no talking or writing. Very very nice videos. Keep up the good work , is there a chance you can make a minimalist gemstone ring from scratch because they are a bit small so I’d like to see your approach to how you make it.
Thank you Jeff. I soldered the shank on using easy 20 gauge wire that I melted into a ball first so the surface tension of the flux would pull it into contact with the plate and the two ends of the shank.
Love this video ,its inspiring. You make it look easy. Could you please explain about the surface tension of the flux pulling the ball of solder through. Does this make for a better join? Would it work with any flux? Thanks
The surface tension from the liquid flux pulls the solder ball to the shank so it has good contact with the shank and the plate as long as it is wet. If heated carefully and evenly the solder will stay in place and the flux will liquefy and the surface tension will again be present. When the solder melts the surface tension of the molten solder will help it to flow into the joint leaving little to no excess solder on the backing plate. Using heat control to pull the solder through the joint ensures best bond attainable. This is my preferred method for achieving a clean strong bond. I couldn't say whether it is better than other methods.
Hello, I follow you from Spain. I am learning and thanks to you especially. I have two questions, I hope you can help me. What gauge is the base sheet? and I see that a tripod is not necessary. Do you think a block of carbon would be enough to weld? I want to make a ring with three bezel, can I weld it on a carbon block or will it be better on a tripod giving it heat from below? Thanks for your help
what is that tool you are using to set the stone....? that ring is gorgeous you can give it to me if you like....thank you for your videos. should I use a split shank for decorative or technical reasons ..?
A bit of both on why choose a split shank. The split shank helps a little in keeping the ring balanced on the finger in my opinion for a larger stone. I used a hammer and punch for the final tightening of the bezel. Here is a link to another video I made that is more focused on the hammer and punch method for stone setting: ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-NIpc_fy67zU.html Starting the punch at a low angle to push the bezel to the stone and then finishing at steeper angles is the key to success when using this method.
Hi! Why do people always say to apply the heat from underneath when soldering on a bezel to a back plate... to prevent the solder from traveling up the sides the bezel. But then I see pros like yourself just heat the piece on the block, round and round? I been using the titanium trivets.
I might be able to make rings for you similar to this one for you. Depending on the stones you have and how many I would make the price would be around $65.00 to $85.00 each. My email address is steve@blueskyjewelry.com
I have a trick for centering, you flux the piece and heat it facing towards you on a third arm so you can see it, heating the flux just until it is dry but not turned transparent makes it act like glue so you can pick the piece up with tweezers to flip it over and set it down and then solder it because the flux is still useable and the back is now facing you and it's centered because you've seen it from the front already.
Can you explain what you are doing and also can you put the camera over your head looking down on what you are working on cus I can’t see shit and the music choice mannnn am I watching a thriller movie
