Making A Very Short Pocket Survival Fire Piston Fire Lighter

Подписаться 51 тыс.

Просмотров 4,4 тыс.

50% 1

See how I make probable the shortest fire piston on my Myford ML7. These fire pistons or fire syringes are an excellent project to make on the lathe as they are quite easy if you get the machining correct with good finishes. (Camera Used Sony DX-410VE)
SOME TOOLS USED IN THE VIDEO & SOME SPECIAL OFFERS:-
MGEHR 1010-2 10x10x100mm Lathe Turning Tool Holder With 4pcs MGMN200 Inserts -- bit.ly/3wg2aP4
Extra links:
Banggood & Clearpay Sale -- bit.ly/3dywaiD
Deposit Sale -- bit.ly/2Ut4uVI
Steve Jordan Coupon -- bit.ly/34hz2eJ

Опубликовано:

2 июл 2021

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 24

@JohnsOrganWorks 2 года назад

Nice work. I'm impressed you can get enough compression with such a short stroke.

@jamescopeland5358 3 года назад

Great job and project Steve! Thank you

@TheKnacklersWorkshop 3 года назад

Hello Steve, Nice work as always... I was just thinking that with COVID restrictions nearly gone maybe you could make that video you promised showing the Gun Dog Training Launcher in action... Take care. Paul,,

@SteveJordan 3 года назад

Hi Paul Thanks yes I will do that one sometime soon I think. Regards Steve

@donaldnaymon3270 3 года назад

Great video. Nice work Thank you for sharing.

@timmienorrie 3 года назад

Whst a fun project. Well done.

@lisag2771 3 года назад

Another great job and video.

@jdmccorful 3 года назад

Nice project!Thanks.

@6NBERLS 3 года назад

Most excellent.

@tjwoolsey478 2 года назад

Brilliant

@guye7763 3 года назад

Just want to be first. Well made, thanlks.

@howardosborne8647 3 года назад

That 10/10 MGEHR 1.5 seems to work quite well for a relatively cheap tool. I have a more expensive branded 1.5 MGEHR with 20/20 shank. I'm pretty certain your knurler body was rubbing some of the knurl off as you were traversing. Perhaps I'll give one of the banggood internal groove MGEHR tools a go after seeing how good this one works.

@dalemcinnes1834 3 года назад

I had noticed something odd when watching so I went back and re-watched and you can definitely see the knurler body was taking off the knurling. Would be a simple fix. Good eye. Dale in Canada

@olegkondratenko7409 3 года назад

Зачетная зажигалка.

@nullsnaggle5198 3 года назад

Could that boring bar you used halfway through the video be used to cut threads?

@SteveJordan 3 года назад

Hi No you need a tool specifically ground for thread cutting. Regards Steve

@nullsnaggle5198 3 года назад

@@SteveJordan alrighty then gg

@supermetaltastic Год назад

Where are the plans? No dimensions are provided in the video.

@SteveJordan Год назад

Hi Adam, I don't ever use plans as I make things up as I go along.

@supermetaltastic Год назад

@@SteveJordan Alright, 1.What was the diameter and depth of the hole? 2. What were the O-ring specs? 3. Did you hand feed the last part of the boring bar? 4. What is the diameter of the piston? I made one, but it was about 3.5" deep and about .3906 diameter then lapped with fine timesaver compound with a brass lap. The bottom of the hole was the point of the drill. I'm impressed with amount of stickout on that boring bar. Just like you found the surface finish and double O-ring with chapstick as lube was critical to success.

@SteveJordan Год назад

Hi Adam, I did hand feed the boring bar to the end of the hole, which was finished with a flat bottom drill. The flat bottom drill does not cut the diameter of the hole, just the bottom face of the bore, so it is dead flat with no indent. I will measure mine up and give some dimensions this week. When I get one back from my son to measure. He uses them for his bushcraft teaching. I will measure the o/rings I use. I do everything by feel and don't normally take measurements. If a piston is too tight when the o/rings are fitted, I just take them out and skim a bit more from the bottom of the groove until I get it right. That's why I haven't any measurements to hand. Regards Steve

@SteveJordan 3 года назад

MGEHR 1010-2 10x10x100mm Lathe Turning Tool Holder With 4pcs MGMN200 Inserts -- bit.ly/3wg2aP4 Extra links: Banggood & Clearpay Sale -- bit.ly/3dywaiD Deposit Sale -- bit.ly/2Ut4uVI Steve Jordan Coupon -- bit.ly/34hz2eJ

@SteveJordan 3 года назад

EXCELLENT DEBURRING TOOLS USED IN THIS VIDEO:- NG1000 NB1100 Burr Handle Scraper Deburring Tool -- bit.ly/3wlnoeC NG1001 Burr Handle 11pcs BS1010 S10 Blade Set -- bit.ly/3wlffH9 Drillpro Chamfer Tool Countersunk Blade -- bit.ly/3jJG3y0 10Pcs RJX Handle Scraper Deburring Tool Deburring Trimming Blade -- bit.ly/3yusBlU