Master Mechanic finds Bad Steering Angle Sensor. ESP BAS, Traction Control, ABS lights are on. 

Thanks, my vehicle has a similar problem with all the different warnings lights on. I’m glad it might be a sensor.

Great video thanks

my 2005 Audi A8L has steering angle sensor voltage supply terminal 30 and front passenger wheel speed sensor faults. The steering angle reset requires VCDS which I don't have

This guy is making big money off you just being a mechanic & listening to his lingo is hilarious

My 2013 Suburban LTZ has the traction control light and the service stabilitrak light on. Many people advise me to check the steering position sensor connector. Theres mention of putting a foam spacer to keep the connector from leaning over and to prevent corrosion?

You are wrong here the whole steering column does not need to be removed you just need to remove the steering wheel then the clock spring and it’s attached to the back of the clock spring

Thanks

I have abs, esp bas and tc lights on thinking thats my problem too..i read on a jeep forum that it may be able to re calibrated?? Doesnt hurt to try. Then go from there

Thanks for that I just change rack and pinion so after that the code c0d35 steer wheel sensor signale implausible

HI GUY HOPE U CAN POST THIS CAUSE I AM COMPUTER CHALLENGED. 2009 CHALLENGER MANUAL TRANS. ESP BAS LIGHT CAME ON WHEN TIRE CAME OFF CURB OUT OF GAS STATION RAMP N TIRE SPUN.ESP (ELECTRONIC STABILITY CONTROL)BAS(BRAKE ASSIST PROGRAM) I DID ALL THE TRICKS ON U TUBE. SPIN WHEEL ALL THE WAY TO RIGHT THEN TO LEFT. TURNED LIGHT OFF TEMPORALLY. TURNED CAR OFF WHILE IN NUTRAL WHILE GOING 20 MPH N RESTARTING IT. TURNED LIGHT OFF TEMPORALLY. LOOKED INTO STEERING ANGLE SENSOR N FOUND THAT IF THIS HAPPENS TO U , IT SHOULD RESET ITSELF AFTER ABOUT 100 MILES OF DRIVING OR SO.IF NOT,THERE ARE CODE READER DEVICES THAT HAVE SAS ON THEM. THIS RESETS YOUR STEERING ANGLE SENSOR. DO THIS BEFORE CHANGING IT.ALSO WHEN U DO CHANGE IT IT SHOULD BE RESET TO CENTER.

my traction control light went on after changing my steering wheel.. and scanner says it’s angle sensor. My question is angle sensor mounted on clock spring?

I have a 2010 dodge Journey ESP/BAS and traction lights come on at random which is causing my car not to shift out of park when lights are on. I have to shut my car off and turn back on to get lights to shut off and able to shift out of park any advice?

I had my left axle replaced and I noticed the steering wheel was not aligned and as I drove home the Jeep made this rumbling noise and immediately the ESP BAS and traction sensor illuminated on the dashboard. My question is could the replacement of the axle damage the Steering Angle Sensor? Any feedback would be appreciated.

so the angle sensor is mounted on clock spring?

I'm having similar issues with my 09 caravan and the dodge dealership wants big money to fix it, so i solved the problem by trading it in for a toyota lol

Can code C121C (Torque Request Signal Denied) be caused because of code U0126 (Lost Communication with Steering Angle Sensor)? I do have code C2100 (Low Battery Voltage) And i have been told that my car seems to have a shortage somewhere because the lights dim when we ran an alternator test (good) and battery test (bad which was replaced) when i turn my steering wheel all the way to either side, it makes a nasty noice that seems to come from the power steering pump. I also have problems with my blinkers and my headlights be glitching at times. Sometimes i have my car on idle and they flick even my dashboard so i know it’s something electrical. The history with this car (2005 Chrysler 300 5.7L V8) is that it had a bad heater core so they ended up replacing it.

Did the angle sensor fix it?

Did you say he does mobile diagnostics?

PLEASE READ: they guys in this video took the expensive way out although the video was informative. Look for my name and video on a cheaper way to fix the problem.

Are you in Canada or USA?

He never mentioned the simple reset that the maker suggested to try first

I have a c2200 & c2205 code

Master mechanic lol

Bloke is a bullshitter, you are being had over, remove steering column, lmfao

This why i hate mechanics. Always exaggerating the fix. Im gonna have to open a shop and though i may not be profitable to be rich, i can gain business by being honest!! The whole thing dont come out. Just steering wheel and clock spring. Its on back if clock spring. Whole column my butt!! 😆

A master mechanic but doesn't know the order of the letters for the service light 🤦

Completely wrong....