Mazda 3 Spark Plug Change Replacement 2.0L, 2.3L, 2.5L

Подписаться 25 тыс.

Просмотров 96 тыс.

50% 1

Quick and easy video showing you how to change the spark plugs in a Mazda 3.
NGK Iridium IX spark plugs for 2.0L: amzn.to/3v8xdwB
NGK Iridium IX spark plugs for 2.5L: amzn.to/3v8xdwB
Torque Wrench: amzn.to/2Cj8wUv
Ratchet Set With Deep Sockets: amzn.to/3RbewGu
Amazon Affiliate Links
Please Like, Comment and Subscribe!
Subscribe Here: / @5minutefixit
2010 Mazda 3 Spark Plug Change
Mazda 3 Spark Plug Replacement
Tags: mazda 3 spark plug, mazda 3 spark plug change, mazda 3 spark plug replacement, mazda,spark plugs, mazda 3, how to change spark plugs on mazda 3, how to replace spark plugs on mazda 3, ngk IX, how to change spark plugs in mazda 3, how to replace mazda 3 spark plugs, replacing spark plugs on a mazda 3, how to change spark plugs in a car, how-to, diy, spark plug, easy, best, 2010 mazda 3 spark plug replacement, 2011 mazda 3 spark plug replacement, 2012 mazda 3 spark plug, how to

Авто/Мото

Опубликовано:

6 ноя 2019

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 207

@anthonyigania8465 4 года назад

This is probably the clearest how to car video I’ve ever seen. Great work!

@5MinuteFixit 4 года назад

Thank you for the compliment! My goal is to make short and to the point DIY and how-to videos without any fillers. Thank you for watching!

@linuxdb1106 4 года назад

I replaced spark plugs in our 2008 Mazda 3 today and this video was super helpful and very easy to follow. Probably the best step-by-step car video guide that I ever watched. Thank you very much! I didn't use a torque wrench as I didn't have one but the new plugs were pretty snug and tight and I was careful not to overtighten them. On a side note, I noticed quite a bit of dust, sand and other debris so I vacuumed the area before removing the coil packs but was careful while doing so. Thank you!

@5MinuteFixit 4 года назад

Thank you for the compliment, I try to make videos that are very clear and with no fillers. Thank you for watching and if you haven’t already please consider giving the video a thumbs up and subscribing. Thanks again!

@MorrisDugan 2 года назад

I was reluctant to get a torque wrench where the torque to tighten the plug is at the very low end of the wrench. I did a little digging, and a chart told me to tighten a quarter turn as a rule of thumb for plugs this size. (I assume this means a quarter turn past hand tight.)

@MorrisDugan Год назад

UPDATE - I changed the plugs a couple of days ago. The plugs in there must have been the originals - they are marked "Ford" and 6M8G-12405-BB (Mazda #) and ILTR 5A-13G (NGK #), which corresponds to the NGK "Laser Iridium" plugs. There's no gasket on the the old plugs or the replacements. It's set up in the car to be almost impossible to cross-thread them. I found it impossible to tighten 1/4 turn, but I probably tightened more than 1/8. After I was done, and had a successful test drive, I took another look at the little boxes that held the new plugs, and noticed that it had a little graphic showing that you tighten them 1/16 turn! Now I'm thinking I should loosen the plugs and try to be precise about tightening 1/16 turn.

@33fivers 10 месяцев назад

Does the 2008 Mazda use the same spark plugs as recommended for the 2010?

@paulbayne3392 3 года назад

My local Mazda dealer wanted $350 to change out the 4 spark plugs. I feel like I may spend $60 at most including the torque wrench and do this in 15 minutes after watching your video. I watched a half dozen or so about this topic and this was by far the best and gave me the most confidence. I'll let you know how it comes out.

@5MinuteFixit 3 года назад

It really is a very straightforward process, take your time and you should be fine. Let us know how it turns out. Thank you for watching and please consider giving the video a thumbs up if you haven’t already! Thank you!

@theultimatemale6820 28 дней назад

$350 FOR A 15 MINUTE JOB. THE DEALERSHIPS ARE OUT TO RAPE US. JUST LEARN HOW TO DO MORE BY WATCHING THESE VIDEOS.

@jojobmw9400 4 года назад

Great point about NOT using anti-seize! Throws off the torque values. Good video- clear and to the point!

@5MinuteFixit 4 года назад

Thanks for the compliment! Yes I’m sure that most people aren’t aware of the fact you shouldn’t use anti-seize. I think they have good intentions. If you found this video helpful please hit the thumbs up button and consider subscribing! Thanks again!

@jojobmw9400 4 года назад

5 Minute Fix it - yes, I did sub, thx!

@geoffobrien1300 Месяц назад

I would rather use it and I do use it every time without issue.. going for a torque figure is irrelevent on plugs, all they need is to be snug.

@aderizzio 2 года назад

Dealership was charging me $363 to replace my spark plugs, I paid $64 for everything, and did it in 15 minutes after watching this video. Thank you.

@5MinuteFixit 2 года назад

That’s great! I’m glad you were able to save some money! Thank you for watching and please consider giving it a thumbs up if you haven’t already! Thank you!

@Crybaby-Media 3 года назад

Happy to see positive comments. The other videos have people criticizing heavily in the comments. I feel much safer following your directions

@mimimineau5040 3 года назад

I need my spark plugs replaced. I've never done done it before, so I've been watching videos, and yours is the best. I actually think I can do this!! Thank you. Your video isn't too long. I understand your directions.

@5MinuteFixit 3 года назад

Mimi Mineau thank you for watching and if you have all the tools and the right spark plugs this is a very easy job! Good luck, let us know how it goes and please consider giving the video a thumbs up if you haven’t already! Thank you!

@drbortz3699 2 года назад

💥💥💥‼️ Thanks to your video, I’m pleased to share that I have successfully changed my 3’s spark plugs for the first time, then taken it for a spin, and there have since been tens of thousands of happy little explosions, and not a single one of them was unexpected 🥳. Thanks for your clear, concise, and thorough walkthrough.

@5MinuteFixit 2 года назад

Love it, comment of the month goes to you! Thank you for watching and please consider giving the video a thumbs up if you haven’t already! Thank you!

@MrSerhum Месяц назад

Wow, just did mine in 25 minutes using this vid. Fairly straight forward. I used a long nose pliers to take out the plugs and stick the new one in. Easy peasy. Many thanks. Car purred after.

@5MinuteFixit Месяц назад

@@MrSerhum Thank you for watching, I’m glad the video was helpful! Please consider giving the video a thumbs up if you haven’t already! Thank You!

@theultimatemale6820 28 дней назад

THANKS ALLOT FOR THIS INFORMATIVE AND SIMPLE VIDEO. YOU JUST SAVED US FROM GETTING RAPPED BY THE MECHANICS.

@5MinuteFixit 25 дней назад

Thank you for watching, I'm glad it was helpful! Please consider giving the video a thumbs up if you haven't already! Thank You!

@NIZAROLAZ 2 года назад

One pointer to add ... if you have compressed air, blow the dust & debris from the cavity where the plugs are located after removing coils while plugs are still in place to minimize the debris and dust from entering the cylinder while removing and installing plugs.

@5MinuteFixit 2 года назад

Thank you for this, hopefully others will see this and use this tip!

@konyecstrength4life 4 месяца назад

Best upload for changing Mazda 3 spark plugs. No frills instructions. I don’t understand why some people say you must remove the negative battery terminal first before beginning. You pull out the plug from the coil anyway so I don’t see how you could short something, especially if ignition is off.

@5MinuteFixit 4 месяца назад

Thank you for watching, I’m glad it was helpful! I agree that it isn’t necessary for the battery to be disconnected. Please consider giving the video a thumbs up if you haven’t already! Thank you!

@5MinuteFixit 4 года назад

If you need to pick up the spark plugs or tools: NGK iridium IX spark plugs for 2.0L: amzn.to/3v8xdwB NGK iridium IX spark plugs for 2.5L: amzn.to/3v8xdwB Torque Wrench: amzn.to/2Cj8wUv *Amazon Affiliate Links* Thank you for watching! If you found this video helpful please give it a THUMBS UP 👍 and consider subscribing! THANK YOU! I appreciate all the support! SUBSCRIBE HERE ▶︎ ru-vid.com/show-UC8BzgKWkH0AGzCOORKK7Vwg

@onepurestilovelez1671 4 года назад

What size is the torque wrench?

@jayperez1769 3 года назад

@@onepurestilovelez1671 it has to be at least 10lbs of force it's a 3/8

@JohnMillerUSA 3 года назад

🛠 🏆 5-star DIY video. This is how you make a great, useful, and easy-to-follow car maintenance video: tripod-mounted camera, no distracting background music, and methodical explanation every step of the way. When I hear shops charging $200-300 for a 4-plug swap on the Mazda3 2.3 engine I have to laugh. This is not a hard maintenance item if you follow this video. The only thing I would add is that I always blow out the spark plug hole before removing the spark plug. You don't want grit, sand, or other debris to fall down into the hole once the spark plug is removed.

@5MinuteFixit 3 года назад

Thank you for the compliment! I try to make short and to-the-point how-to videos so I appreciate that! Thank you for watching and that is a good point about blowing out before removing the plug! Thanks again!

@Phlacc 3 года назад

This is the best how-to video I've seen. Really well done, quality work.

@5MinuteFixit 3 года назад

Thank you for the compliment and for watching, I appreciate it!

@youtubehub8190 2 года назад

I checked many videos, but used this one as main guidance to change my own spark plugs. Huge thanks, very detailed and very easy to understand

@5MinuteFixit 2 года назад

Thank you! I appreciate the compliment! I try to make my videos as clear and easy to understand as possible! Thank you for watching and please consider giving the video a thumbs up if you haven’t already! Thank you.

@ziploc2000 2 года назад

I never changed a spark plug before, I didn't even know exactly where they were in my engine, but did all four very easily today thanks to your guide. The owner's manual may possibly explain where to find them, but if it does the information is buried.

@5MinuteFixit 2 года назад

Great job! Im glad you were able to do it with the help of my video! Thank you for watching and please consider giving the video a thumbs up if you haven't already! Thank you!

@jimjones1630 3 года назад

Great video! Everything i wanted to see, and nothing i didn’t. 10/10

@5MinuteFixit 3 года назад

Thank you for watching! That’s how I like to make my videos, short and to-the-point, thanks for the compliment! Please consider giving the video a thumbs up if you haven’t already! Thank you!

@andrewdavid7474 Год назад

great video. did my own plugs today; this video made it incredibly easy! only thing i needed to buy was the plug socket and the plugs themselves. thx again!

@5MinuteFixit Год назад

That's great! I'm glad you were able to tackle the job with the help of the video! Thank you for watching and please consider giving the video a thumbs up if you haven't already! Thank you!

@codyogozalek228 4 года назад

Wow, such great camera quality!

@5MinuteFixit 4 года назад

Cody Ogozalek thank you for the compliment, I am trying out a new camera and so far like how things look!

@r6singh Год назад

Thank you. I just followed this video to change plugs on my Mazda. One of the best explanations I’ve ever followed. Cheers

@5MinuteFixit Год назад

Thank you for watching and for the compliment! I’m glad it was helpful! Please consider giving the video a thumbs up if you haven’t already! Thank you!

@MarcoMedina_P 2 года назад

You know what's funny I know how to change out spark plugs but I got a defective one so I freaked out a little bit and this video was helpful to remind me I didn't do anything wrong, thanks again!

@5MinuteFixit 2 года назад

Thanks for watching! Hopefully you were able to swap out the defective one without an issue!

@FlyingsCool 10 месяцев назад

Love your video... I hate so much the people who love to talk. Perfect instructions.

@5MinuteFixit 10 месяцев назад

Thank you for watching, and for the compliment I’m glad it was helpful! Please consider giving the video a thumbs up if you haven’t already! Thank you!

@rosscarter8913 3 года назад

Honestly one of the best videos I've seen! Thanks for taking the time to make a hugh quality video

@5MinuteFixit 3 года назад

Thank you for watching and for the compliment, I appreciate it! My goal is to make videos without any fillers or fluff that are straight to the point and are easily followed. Please consider giving the video a thumbs up if you haven’t already! Thanks again!

@FeisarX Год назад

Changed Mazda 5 plugs thanks to this video. Appreciate it!

@5MinuteFixit Год назад

That’s great! I’m glad the video was helpful, please consider giving it a thumbs up if you haven’t already! Thank you!

@blessedinpark Год назад

Very easy to follow video. Now to put instruction to action. Thanks.

@5MinuteFixit Год назад

Thank you for watching, I'm glad it was helpful! Please consider giving the video a thumbs up if you haven't already! Thank you!

@GSDReny 3 года назад

Great video. Quality was amazing and instructions were simple and straight to the point I wish people made more videos like this great job. I definitely liked and subscribed to your channel. I’m doing my plugs today and this just made it easier in my mind to do the job. Thanks man. One thing I do know for sure about doing plugs and very important is do one at a time that way you don’t mix up your coil packs and they get put on the same plug.

@5MinuteFixit 3 года назад

Thank you I appreciate it! I strive to make high quality easy to follow videos that don’t have fillers and are straightforward. Thank you for subscribing and for the thumbs up! Good luck on the plugs and let us know how it goes!

@GSDReny 3 года назад

@@5MinuteFixit I don’t have a torque wrench so how tight do I tighten the spark plugs. My neighbour said a half turn after their snug and my buddy said a quarter turn after their snug. I don’t wanna tighten too much and I don’t wanna tighten not enough. Could you help me please? Replacing them as I type this.

@5MinuteFixit 3 года назад

@@GSDReny sometimes it will show you a diagram on the spark plug box...if there isn’t one there I would do 1/2 turn after you hand tightened them.

@GSDReny 3 года назад

@@5MinuteFixit got the new plugs in and everything went smooth. Thanks your video was on point and made it easy.

@5MinuteFixit 3 года назад

@@GSDReny that’s great, thanks again for watching and letting us know how it turned out!

@bicboss4486 Год назад

So i can save my self hundreds of $$ if I do this myself rather than going to the dealer. Anyways nice video. Straight to the point... no unnecessary info👍

@5MinuteFixit Год назад

Thank you for watching! Please consider giving the video a thumbs up if you haven’t already! Thank you!

@rodgerbradford4523 2 года назад

Great video. Very clear and concise. Thank you for the tutorial!

@5MinuteFixit 2 года назад

Thank you for watching and and for the kind words! Please consider giving the video a thumbs up if you haven’t already! Thank you!

@baddiemaes5750 5 месяцев назад

Very excited to change my spark plugs for the first time at 177,000 miles

@5MinuteFixit 5 месяцев назад

That’s great I’m glad the video was helpful! Let us know how the spark plug job goes!

@KeeganRobbins 3 года назад

Very helpful video - exactly what I needed, and I changed them without a hitch! Thanks for making this.

@5MinuteFixit 3 года назад

That’s great I’m glad it was helpful! Thank you for watching! Please consider giving the video a thumbs up if you haven’t already! Thank you!

@luisjalvareztorres8481 2 года назад

Excellent, excellent video. I need to replace the spark plugs on my 2010 Mazda 3 and this video gave me confidence in doing it myself. One question. I’ve seen other videos were people gapped the new spark plugs before installing them. I remember back in the day when that was necessary, but I didn’t know people still do that. Is gapping the spark plugs necessary?

@5MinuteFixit 2 года назад

I would check the gap, most plugs come pre-gapped so I would just check to make sure it’s within spec. Thank you for watching and for the compliment! Please consider giving the video a thumbs up if you haven’t already, thank you!

@luisjalvareztorres8481 2 года назад

@@5MinuteFixit thanks for the quick response. Much appreciated.

@5MinuteFixit 2 года назад

Absolutely! Good luck with the spark plug change!

@luisjalvareztorres8481 2 года назад

@@5MinuteFixit thanks!!!

@beardedlocoswoodworks 3 года назад

Nice video, very detailed thanks. Just bought my son a 2006 Mazda 3 hatchback

@5MinuteFixit 3 года назад

Thanks I’m glad you found it helpful! I hope you have good luck with your son’s new Mazda!

@despairfollows591 11 месяцев назад

What should I be searching for on amazon for the parts? I found the torque wrench from the link and the long extension but am completely lost on the regular and small ratchet and small extension

@5MinuteFixit 11 месяцев назад

Are the links not working? I apologize.

@allyboy8 Год назад

Thanks for that. You made it look easy. 👍

@5MinuteFixit Год назад

Thanks for watching! I’m glad it was helpful, it is a fairly straight forward process and you shouldn’t have any issues doing it yourself!

@user-li8yu2tu6g 11 месяцев назад

Do the spark plugs come pre gapped? If not wat is the gap needed for the 2.5L mazda

@5MinuteFixit 11 месяцев назад

Yes most plugs come pre gapped but it should have been noted to check the gap to ensure they were within spec. Thank you for watching!

@altitudefpvphotography4616 2 года назад

Thank you for the great video!

@5MinuteFixit 2 года назад

I’m glad it was helpful! Thank you for watching and please consider giving the video a thumbs up if you haven’t already! Thank you!

@Badger345 19 дней назад

Thanks I have 2022 Mazda 3 dealer wants to change spark plugs at 40k miles

@mman8795 3 года назад

Qaulity video, easy and straight forward, thank you!

@5MinuteFixit 3 года назад

Thank you for watching! Glad it was helpful and thanks for the compliment on the video!

@eliasfigueroa923 4 года назад

Very clear thanks for sharing God bless you

@5MinuteFixit 4 года назад

Thank you for watching! Glad you found it helpful!

@tonymartinez8418 5 месяцев назад

Do you have to disconnect the battery when replacing spark plugs because I heard they do some weird stuff if you disconnect the battery?

@peters7278 3 года назад

Do u check the electrode gap? I just bought the spark plugs for my Mazda 6 and they come as 0.040" out of the box, but I've seen that Mazda recommends 0.052" for the 2.3L engine.

@MorrisDugan Год назад

I checked the gap, and I did adjust them to 0.052".

@harmotiixxo5323 2 года назад

Thank you man this helped out a lot

@5MinuteFixit 2 года назад

Thank you for watching! I’m glad it was helpful!

@katiuskadel7310 4 года назад

thanks for this awsome video!

@rbbach1945 Год назад

Excellent video. Tks for time/trouble. Rick,77,Seattle 2015 Mazda 3 iSport HB

@5MinuteFixit Год назад

Thanks for watching! I'm glad it was helpful!

@manuelsares5206 2 года назад

video was very helpful. thank you very much

@5MinuteFixit 2 года назад

Thank you for watching! I’m glad it was helpful! Please consider giving it a thumbs up if you haven’t already! Thank you!

@frapeyou 4 года назад

hey great little video series for Mazda 3 2010, any chance you could do a detailed video about changing the transmission oil? (also if you do all the basic DIY videos like this playlist but with different old cars, you could become an established brand/channel in no time, (like your the channel people come to for the maintenance videos on their cars) I believe you will blow up with time)

@5MinuteFixit 4 года назад

snowmanmike thanks for the compliment! I try to make to the point videos with no filler. I hope people will find the value in my channel and encourage people to subscribe if they find the videos useful. I might do a Mazda 3 transmission video in the somewhat near future, stay tuned. Thanks again for the compliment and make sure you give the vids a thumbs up! Thank you!

@frapeyou 4 года назад

@@5MinuteFixit try to watch what Graham Stephan does on RU-vid (he's a finance channel) but the way he asks for questions and likes and shares is a good start, the only thing with youtube us time is key, like some channels do amazing videos for 4 years, barely make it and year 5 they have 1 million subs and make 100X what they made the year before)

@5MinuteFixit 4 года назад

snowmanmike I’m in it for the long haul, I enjoy making instructional videos and I just do it for fun/hobby but that would be great if it turned into something! Thanks again and I will check our Graham!

@simonblunden2151 2 года назад

Perfect. This is my weekend project. Quick question. Do you need to adjust the gap on the spark plug head or just go with how they come from box?

@5MinuteFixit 2 года назад

Most come “pre-gapped” but I would just double check with a gapping tool before installing. Hopefully this helps! Thank you for watching and please consider giving the video a thumbs up if you haven’t already! Thank you!

@AdrianLopez-ne9hn 2 года назад

When the plugs are iridium, I would not recommend gapping the plugs as the electrode tip is so small and fine that you can chip pieces from the tip. I know this from experience. I was told to never gap iridium plugs by a mechanic friend. Most come pre-gapped already, just find the ones that fit the recommended gap spec for your car. My Mazda 3 has a gap recommendation of 0.05 inches and the Autolite iridium plugs I bought came pre-gapped at 0.050. Makes the installation hassle free.

@sergios.2276 3 года назад

Thank you, just simply, thank you.

@NorthernBulls 11 месяцев назад

As a girl I'm very intimidated. But I'm not willing to spend 350$ for the mechanic to change them. I will try myself. This seems legit straight forward

@5MinuteFixit 11 месяцев назад

It is very straightforward, you shouldn’t have an issue doing this yourself. Take your time and you should be totally fine! Thank you for watching and please consider giving the video a thumbs up if you haven’t already! Thank you!

@macandcheese516 2 года назад

My 2005 mazda has one of the yellow bracket things on the first coil pack. I was wondering if there was a way to get it off?

@josephnunnally8734 Год назад

Good video as I have the 2.5 in my 2011 mazda cx7

@5MinuteFixit Год назад

Thank you for watching, I’m glad it was helpful! Please consider giving the video a thumbs up if you haven’t already! Thank you!

@auralepiphanies4055 2 года назад

any tips on getting an old stuck parkplug out of my mazda? I dont want to strip it but its in tight-the other 3 were mega corroded...

@surindergill4480 3 года назад

To the point, Well explained, Thanks.

@5MinuteFixit 3 года назад

Thank you for watching, glad it was helpful! Please consider giving the video a thumbs up if you haven’t already! Thank you!

@NorthernBulls 11 месяцев назад

My car is a 2.3 2008 mazda 3. What spark plugs would I buy. Your link says 2.0 and 2.5

@palekenamauuawaa1248 3 года назад

Thank you for share it was good video cause have 2005 mazda 3 2.3L 5spd have fast car

@rudyarias4102 3 года назад

Hi great video. I’m getting a P0172 code. Any idea what it can be?

@santoslopez7415 2 года назад

I did these but now when I drive and go to a stop my car shakes and feels like it’s losing power any help?

@joyzz6533 Год назад

will a 3" extension long enough to take the spark plugs?

@sinaguso1 2 года назад

These 4 cylinders jobs are easy af changed my bros kia soul. My v6 caddy was a pain , had to take off manifold

@5MinuteFixit 2 года назад

I agree most 4cyl are pretty straightforward, the transverse V6’s are usually more involved like you said with your caddy. More things to move so you can access the plugs. Thank you for watching!

@Danny-dh2pg Год назад

Can I do this if I only have a 3 inch extension?

@greedycat4026 5 дней назад

is it important to change them one by one the way you did? or can u take all 4 of them out and then install new ones

@5MinuteFixit День назад

Either way is fine. Thank you for watching! Please consider giving the video a thumbs up if you haven’t already! Thank you!

@ericmillersprospectingchan3424 2 года назад

always check gap of the plug

@Jay-qb5vg 3 года назад

make sure to check your gap! you never did in this video... .052 for the 2.5L

@zosorob4559 2 года назад

What about for a 2.0

@Jay-qb5vg 2 года назад

@@zosorob4559 .052, the same

@marcov9808 4 года назад

Is dielectric grease necessary for the spark plugs?

@5MinuteFixit 4 года назад

It isn’t necessary but it definitely wouldn’t hurt to put some on the ends of the cool packs.

@user-mf8mj4iu5b 9 месяцев назад

Do you need to gap the plugs, or are they nicely gapped already for the Mazda?

@5MinuteFixit 8 месяцев назад

These plugs are iridium and come pre gapped, hopefully this helps!

@rudyarias4102 2 года назад

Hi great video. I removed the spark plugs and one of them had motor oil on it. What does that mean?

@5MinuteFixit 2 года назад

This may answer your question there could be a few reasons and I think this explains them well, thank you for watching: cartreatments.com/oil-on-spark-plug/

@sitorp116 4 года назад

Would this apply to a 2004 Mazda 3 2.0 as well?

@5MinuteFixit 4 года назад

The general process is the same just double check that the spark plug is the correct one and the torque spec is the same! Thank you for watching! If you found this video helpful please give it a thumbs up and consider subscribing! Thank YOU!--> Subscribe Here! ▶︎ru-vid.com/show-UC8BzgKWkH0AGzCOORKK7Vwg

@sitorp116 4 года назад

5 Minute Fix it thanks for your response. Appreciate it!

@MKZionUltra Год назад

Old thread. What size spark plug socket on the plugs for 2.0? Tried 14mm and 18. Doesnt grip the plugs..

@justinlavoie8344 4 года назад

Yeah I did all that even got the spark plugs from mazda and now my check engine light came on and it stalls while in driving it. Don't know what to do any suggestions?

@5MinuteFixit 4 года назад

If you have a code scanner I would see what codes the engine is throwing. If you don’t they are invaluable tools for car owners and usually pay for themselves after the first use. The codes it shows will point you in the right direction.

@thomasmackey1705 3 года назад

Could not find the spark plug reference for the Mazda Tribute. Says page no longer exists. Anyone know what plugs are correct?

@5MinuteFixit 3 года назад

Rockauto.com will have the listing by make, model and year.

@paulreed2362 3 года назад

What year Mazda3 is this? Does anyone have a link to exact NGK plugs to use on a 2007 Mazda3? Great video!!

@5MinuteFixit 3 года назад

Thank you for watching, glad you found it helpful! Here is the link for the NGK plugs for your Mazda3. (Amazon Affiliate link) amzn.to/3dMbZyO

@MorrisDugan Год назад

@@5MinuteFixit Isn't it different for turbo?

@FastForza Год назад

So when i removed the coil pack, the seal on the engine chipped off , is that a major problem? Idk what to do

@5MinuteFixit Год назад

It’s not a major problem, but that seal does help prevent debris from going down the tube and resting on the spark plug. The next time the plugs are changed the debris can fall into the combustion chamber.

@sheartzy Год назад

What if I dropped one of my posts 😅how can I replace those cuz now I have a loose coil

@5MinuteFixit Год назад

Oh no…those may be a part that you can only get at Mazda.

@onepurestilovelez1671 4 года назад

What size is the torque wrench

@CrazyCrethon 3 года назад

Looks like a 1/2" drive. Usually used for taking off tires but he used an adapter to use the socket. That is what I do so I do not have to buy another torque wrench.

@douglasmacomber6881 3 года назад

Ty for refreshing ny memory !!! Lol

@5MinuteFixit 3 года назад

Thanks for watching!

@brandonheuving7068 9 месяцев назад

Do the plugs need to be gapped?

@5MinuteFixit 8 месяцев назад

These plugs are iridium and come pre gapped, hopefully this helps!

@ijustwannabeadrummer Год назад

No use of spark plug gapper?

@trevor93939jhxgeyeuejnrnfjdise 3 года назад

My 2007 madza 3 shakes around when I stop. Could changing the sparkplugs fix it?

@5MinuteFixit 3 года назад

Do you mean as you are stopping or when the engine is at idle?

@trevor93939jhxgeyeuejnrnfjdise 3 года назад

@@5MinuteFixit when I'm at a red light

@5MinuteFixit 3 года назад

@@trevor93939jhxgeyeuejnrnfjdise it could be the spark plugs or another ignition component. I would suggest bringing it to an auto parts store and they can scan for any codes that the car may be storing.

@Penumbruh 3 года назад

I know this might be common sense to some people but do I need to disconnect the battery during this process?

@5MinuteFixit 3 года назад

No need to disconnect the battery, there is no power going to the spark plugs.

@yara-rosetrodriguez3022 Год назад

not bad, but i think anti-seize lubricant and dielectric grease is also needed :/ just saying

@GoaWay... 2 года назад

How do you know when you have successfully tightened it to 10lb torque ft?

@AdrianLopez-ne9hn 2 года назад

You use a torque wrench and set it to 10 ft lbs. You should feel the handle click as well as hear an audible clicking noise when you have reached the desired torque.

@GoaWay... 2 года назад

@@AdrianLopez-ne9hn okay than you, Adrian

@brendodaplug661 Год назад

do i need to size my spark plug ?

@5MinuteFixit Год назад

Many new spark plugs come pre-gapped but you should at least verify the gap. Thank you for watching!

@christopherkuhar2965 2 года назад

Do you place any dioelectric grease on the coil pack and do you set the spark gap

@5MinuteFixit 2 года назад

I should have mentioned to check the gap, iridium spark plugs in most cases come pre gapped. Dielectric grease can be applied but only a very thin layer. Thank you for watching hopefully this helps!

@Isitworthitreviews 2 года назад

Great video.. but is it really only 10 ft. lbs?

@5MinuteFixit 2 года назад

Yes as unbelievable as it is that is the torque spec. In general torque specs for spark plugs are fairly low. Thank you for watching!

@Isitworthitreviews 2 года назад

@@5MinuteFixit Thanks for the super quick reply!

@MorrisDugan Год назад

@@Isitworthitreviews You do not want to overtighten. (Or undertighten, for that matter.)

@You-es9dr 3 года назад

Please u need help asap I did all of this and now my car starts like 2/6 times lol what did I mess up

@reconsilver5961 3 года назад

Wires were pulled by accident and now the spark plugs arnt firing? Idk Id have to look to really know

@blakelintzenich7458 Год назад

I thought you have to gap the plugs?

@bugraboztepe8699 3 года назад

What do I do if I do not own a torque wrench?

@5MinuteFixit 3 года назад

A good rule of thumb is to seat the plug down by hand then do 1/2-3/4 turn after that. Do not over tighten. I have a link in the description for a reasonably priced torque wrench if you are interested! Thank you for watching!

@Danny-dh2pg Год назад

Is it ok if there is oil on top of spark plug

@5MinuteFixit Год назад

It’s most likely to be your valve cover gasket leaking and filling up the spark plug “wells” Hopefully this helps, thank you for watching.

@Danny-dh2pg Год назад

@@5MinuteFixit oh okay, so do I need to change it or can I still drive? Thanks for the video and reply

@5MinuteFixit Год назад

@@Danny-dh2pg I would have it repaired as soon as possible and also keep an eye on your oil level as well, until it is repaired.

@Danny-dh2pg Год назад

@@5MinuteFixit Thanks I’ll see if I can

@chrispacheco7493 4 года назад

Do you have to gap them? If so what’s the gap?

@CrazyCrethon 3 года назад

For a Mazda 3 they should be 0.049 to 0.052". I would measure them as quality control for these things are not what they used to be. In a pack of 4 you can easily get 2 that are out of spec.

@chrispacheco7493 3 года назад

HYGRADE thank you I appreciate it

@Djlowrida767 2 года назад

I got a Mazda 3 2010 and it have a misfire on cylinder 3 and the car started to smoke

@MorrisDugan Год назад

Did you change the plugs?

@Warmsunset26 2 года назад

When working on anything mechanical, bette to never....... FORCE anything. If there is resistance, there IS a reason why.

@saintmichael8167 Год назад

Wish my 3 had less than 94k haha

@jeffreyevans6892 2 года назад

I still would have used anti-seize .

@Warmsunset26 2 года назад

rule do thumb : I always '' COPPER SLIP '' anything that has a thread. Easy removal.

@MorrisDugan Год назад

Anti-seize affects the torquing, so you're talking about a can of worms. NGK recommends not using anything. That also makes me nervous, because the threads are in there a long time between changes, and could get stuck. I'm doing the change at just under 70,000, hoping that the plugs won't be stuck when I try to remove them.

@SugarySpiceCakee 2 года назад

Followed step by step but now my car won’t start 😬

@5MinuteFixit 2 года назад

Will the engine turn over?

@bastogne315 Год назад

Changing spark plugs probably biggest waste of time ever.

@konqet7741 3 года назад

I’m sorry turn it 10 pound feet what 😰 I don’t feel like spending $200+ on a shop doing this i wanna do it myself but damn i don’t know all this fancy talk

@5MinuteFixit 3 года назад

You can do it, ft-lbs is a unit of torque (basically how much you should tighten) the spark plug. Another good rule of thumb if you don’t want to over tighten is to hand tighten it without the wrench on until it seats then put the wrench on the extension and turn it 1/2 turn more. Hopefully this helps. The idea is that you want it tight but do not force it. Thank you for watching and please consider giving the video a thumbs up if you haven’t already! Thank you!

@emd3987 Год назад

Nobody sais anything about gapping them

@GMoney-B Год назад

Dude! Can’t wait to try do this on my Mazda following your video. Just taking my car in for an alignment and they quoted me at 330 bleeping dollars to replace spark plugs. I don’t even know if that included the coils. I’m loving doing maintenance on my car especially for stuff like this. Not all heroes wear capes muh man! 🦸‍♂️ I’m at 105k. Hopefully I’m okay with waiting so long, they said I should have replaced them at 75k. How do you know if you need to replace the coils? If you are changing your plugs at 100k, then I’m sure I’m fine too to just change the plugs. Thanks for the great video that’s so clear.

@5MinuteFixit Год назад

I wouldn't replace the coils unless you have a misfire that doesn't get fixed by replacing the spark plugs. Thank you for watching, Hopefully this helps!

@GMoney-B Год назад

@@5MinuteFixit wonderful to hear that. RU-vid is one of the best things. Thank you.