Mazda 323 1 3 Rear Wheel Bearings Replaced 

Great I am glad the video was helpful, Thanks for your support it really helps me build the channel.

Thank You for supporting my channel with your visit and interaction, I am pleased this video was helpful to you. Please feel free to check out the rest of my channel by clicking PLAYLISTS www.youtube.com/@vehiclemaintenanceandrepai3790/playlists for more helpful service and repair videos on most makes of cars available here in SOUTH AFRICA, It is FREE.

Thanks for your compliment and support.

Thank you for the support Steven, it is well appreciated, check out my website for more great car repair/maintenance info, and let me know what you think. www.vehiclemaintenanceandrepairs.com/

That is the idea here at VM@R.com, Cade, thanks for visiting, and your insights it is much appreciated.

Definitely All Joy, it is a marvel of technology, thanks for the support, check out my website and let me know what you think, your opinion will be held in high regard. www.vehiclemaintenanceandrepairs.com/

I am glad you found value in\my videos, Raylene, the intention is to help where I can, thanks for the support.

When one comes in I will. Thank You for supporting my channel with your visit and interaction, I am pleased this video was helpful to you. Please feel free to check out the rest of my channel by clicking PLAYLISTS www.youtube.com/@vehiclemaintenanceandrepai3790/playlists for more helpful service and repair videos on most makes of cars available here in SOUTH AFRICA, It is FREE.

A pleasure, thanks for supporting my channel with your visit.

Glad you like it Janetta and thanks for the support.

Not really Lucky, best and cheaper to get another even if it is a good second-hand unit.

It is always a pleasure, Warnick, thanks for supporting my channel with your visit.

Thank you Siphumele, for supporting my channel, please subscribe if you have not already and press the bell icon to receive all of my latest videos when it is release, it is free, I try my best to provide useful info, check out my website for more useful info too, let me know what you think, I highly regard your opinion. www.vehiclemaintenanceandrepairs.com/

Will do Kay, thanks for the support meanwhile.

You have to buy good quality brand, such as FAG, TIMKEN or SKF

It sounds like the cold start unit is acting up, it may need a little adjustment.

This is what I normally do Turn the nut against the washer, torque 35nm, loosen the nut completely, then turn against the washer, torque 15nm, and lock the nut with a chisel.

much appreciated thank you @@vehiclemaintenanceandrepai3790

A Pleasure

Usually, these markings are made by someone working on the car for reference timing especially when the distributor or related components are removed or replaced and are not usually made in the factory, if your vehicle is making a pinging sound it may be that the timing is over advanced, try retarding the timing slightly and see the results.

It sounds like it may be flooding (getting too much fuel) therefore non starting because it is fouling up the plugs, remove the plugs, if wet then this is the case. You need to either replace the needle and seat or re-adjust the float level.

@@vehiclemaintenanceandrepai3790 thanx a lot , Oom Gary first step then the next. Maybe these processes will help solve this accelaration hesitation too🥺

Hi Mr.G , I'm looking at the float and needle seat. How should it be positioned?🤷

Also cleaned the plugs cos they were fouled (black)

@@MazandiDumapi It should be level, not too high up against the top of the carb when you are holding it upside down, also take the float off and remove the needle to make sure there is no dirt stuck in it.

Thanks, CJ, for your support, I do not have an open workshop, but you are welcome to contact me on 072 486 7810, I am located in Cape Town, check out my website and let me know what you think, there is a contact page with all my info. www.vehiclemaintenanceandrepairs.com/