Mazda 6 Rear Shock Replacement | How To

Подписаться 7 тыс.

Просмотров 25 тыс.

50% 1

Learn how to replace the rear shocks in a 2005 Mazda 6 S without having to remove the subframe.
ACH Automotive Amazon Store: amzn.to/2WHgvUV
ACH Automotive Playlist - • How To Obtain A Massac...
Automotive Diagnostics Playlist - • Mazda 6 - Cooling Fan ...
Mazda Repairs Playlist - • Almost Scrapped! We Go...
Jeep Cherokee Repairs Playlist - • Jeep Cherokee Blowing ...
Follow along on Social Media for more behind the scenes!
/ achautomotive
/ achautomotive
/ achautomotive
#mazda #achautomotive #mazda6 Disclaimer:
Due to factors beyond the control of ACH Automotive, I cannot guarantee against improper use or unauthorized modifications of this information. ACH Automotive assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. Use this information at your own risk. ACH Automotive recommends safe practices when working on vehicles and or with tools seen or implied in this video. Due to factors beyond the control of ACH Automotive, no information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. Any injury, damage, or loss that may result from improper use of these tools, equipment, or from the information contained in this video is the sole responsibility of the user and not ACH Automotive.

Авто/Мото

Опубликовано:

30 июл 2020

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 20

@ACHAutomotive 4 года назад

Monroe OESpectrum 5784 Shocks - amzn.to/2D6xyKu ACH Automotive Amazon Store: amzn.to/2WHgvUV

@toatakeifanga2434 7 месяцев назад

Fantastic information about how to replace shock absorbers. I am mechanical minded but I don't have enough tools to change my Mazda 6 GH hatchback shock absorbers. I think, I will leave this job for a machanic shop, and at least I understand how hard or easy those guys in the shop how to do the job. Thank for your video, you did a very good video presentation.

@ACHAutomotive 6 месяцев назад

Very welcome - it was a pain to do this.

@arlia101 3 года назад

Nice call removing the brake line -- didn't see that in the 1A video for this job. Also, that induction heater is a darned cool tool! Thanks for the video.

@ACHAutomotive Год назад

I love my Induction Heater. It is so useful. It was a tool I bought and I figured I'd use it once and a while but I end up using it all the time. These shocks are a pain to remove, especially without a lift.

@InexplicableBill 2 года назад

Informative video man. I did this on my 2004 6S Hatchback in 2016 when I got all new Bilsteins from warranty. Original Bilsteins were installed by Sullivan Tire 5 years earlier, and I had no idea how difficult it would be to replace these. I have had Alldatadiy for over 10 years for this car so I've always felt confident tackling projects big and small, however this particular project was a ball buster due to the amount of corrosion on all the components and limited access to important bolts. I seem to remember having a terrible time getting the control arm off, as access to that bolt/nut was very limited and getting a socket wrench in there was ridiculous. I was so afraid of stripping the bolt head or nut and being basically f**ked. I did a lot of cursing, walking away and getting snacks and water, more cursing, an occasional busted knuckle... ha. Years prior I remember reading articles about this car when it was new and how genius the rear suspension was for it's discrete packaging allowing for a flat and wide load floor in the trunk. I guess nobody knew the downside to that fancy suspension setup is a hellish job replacing the shocks, most especially for those of us in the salty winter zone. By the way, one things I was surprised you didn't do was use a torque wrench to torque all those bolts down to spec.

@Banks231 2 года назад

Thank you for your video, I finally made this change by myself. very tough to remove the seized lower control arm bolt, have to cut is with reciprocal saw

@algunn5078 9 дней назад

Need the rear bump stopper for 2012 mazda6. Discontinued. Is there an equivalent.

@balinthaui6080 2 года назад

Super informative!

@ACHAutomotive Год назад

Thanks!

@XxTrustNoOnexX 2 года назад

👍👍👍

@ACHAutomotive Год назад

Thanks

@ShadowRing0219 4 месяца назад

Can’t you just put jack stands along the side of the car instead where they are meant to be instead of using ramps or jacking it down the middle and putting a jack stand in the middle?

@tomikallela4562 2 года назад

Before you guys do this, check out 1A AUTO DIY of this, I think that method is less of a paint in the ass.

@Banks231 3 года назад

your mazda 6 gg/gy/gh even has more rust than mine...

@Banks231 3 года назад

will remove the brake disc making this task easier?

@Banks231 3 года назад

why your car does not have GR1L-28-65x at the down side of rear absorber?

@ACHAutomotive Год назад

Yep, New England will do that to a car. And this is clean for up here.

@teenice894 2 месяца назад

Pump Jack, Jack stands and car wheels and your still scared to get under there?😂 I'd trust that over ramps because they fail too. If all 3 fail at the same time it was just your time