Тёмный

MDF VS. PLYWOOD (Which Is Better?? Pros + Cons!!) 

The Honest Carpenter
Подписаться 862 тыс.
Просмотров 1,5 млн
50% 1

Check Out Our FREE GUIDE: 25 Must-Have Carpentry Tools...Under $25 Each!
www.thehonestcarpenter.com/
Affiliate Tool Links:
Dewalt Titanium Drill bits:
amzn.to/2PBJjOX
Milwaukee Drill/Driver Combo:
amzn.to/3uRBiFB
Bosch 12-amp Router:
amzn.to/3rggFAM
Dewalt 12" Sliding Compound Miter Saw:
amzn.to/3rakgAk
(These are affiliate links. When you shop through these links, we receive a small commission at NO EXTRA CHARGE TO YOU. We greatly appreciate the support!)
FOLLOW US ON INSTAGRAM:
/ thehonestcarpenter
FOLLOW US ON LINKEDIN:
/ thehonestcarpenter
CHECK OUT MORE HONEST CARPENTER VIDEOS:
Amazing Flexible Window Screens:
• FLEXIBLE WINDOW SCREEN...
PVC Trim Vs. Wood Trim:
• PVC TRIM VS. WOOD TRIM...
The Truth About Wood Rot:
• THE TRUTH ABOUT WOOD R...
MDF or PLYWOOD? Which material is better? What are the Pros and Cons of both? Most DIYers want to know these things. In this video, The Honest Carpenter breaks down the similarities and differences between MDF and Plywood!
Both MDF and plywood are used in a variety of projects--but they mostly are used to build shelving, built-ins and cabinets. They can also be used in paneling projects.
They are both made of wood byproducts and glue. But, Plywood is made of actual wood layers, or "veneers"; each layer runs 90 degrees to the layers above and below it. MDF is made from fine wood pulp and glue--it's kind of like cake batter that gets pressed into a sheet.
COST: MDF is generally a bit cheaper than plywood, about $35 per sheet. But, plywood comes in a huge variety of grades and types, with prices all over the place. Sandeply and radiata pine plywood tend to be reasonably priced, under $40. But cabinet-grade plywoods, like birch, maple and oak, can be up to $65 per sheet.
STRENGTH: Plywood is much stronger than MDF because of the cross-laid grain layers.
DURABILITY: Plywood is also more durable than MDF for this same reason. The corners hold up better--they don't get dinged or bent as badly.
WORKABILITY: They both respond to tools in a similar fashion. MDF will produce sharper, cleaner cuts than plywood, which tends to tear out. Both can be drilled with drill bits. But, plywood holds a screw much better, especially in the edge. MDF edges should basically never been fastened into without extra support.
DUST CONTROL: Plywood makes dust similar to other lumber. But, MDF makes terrible dust! It's like a powder. Be sure to wear a respirator and hook up vacuum filtration for your cuts.
INTERIOR / EXTERIOR: Plywood comes in both grades. But MDF is really an interior material. The wood pulp fibers make it soak up water like a sponge. It will bloat and rot quickly.
On the whole, I like plywood a lot more. But, MDF is a decent cheap alternative, and it also is very FLAT, which is one of its main advantages over plywood.
Thanks for watching! Be sure to visit us at THE HONEST CARPENTER website:
www.thehonestcarpenter.com

Хобби

Опубликовано:

 

12 июн 2024

Поделиться:

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист
Посмотреть позже
Комментарии : 1,7 тыс.   
@TheHonestCarpenter
@TheHonestCarpenter 4 года назад
Early in my career, I used a lot of MDF as a way to keep prices down for clients. But it's weight and dust drove me crazy! I switched almost completely to plywood, even though it warps more easily and the edges tear out on cuts if you're not careful. If something needs a routed edge, though, without screen trim, I will opt for MDF in those cases. WHAT ABOUT YOU? DO YOU PREFER PLYWOOD OR MDF???
@wr6897
@wr6897 4 года назад
Plywood
@elephantfeet280
@elephantfeet280 4 года назад
I was looking at building a project that required mdf but watching your video I will be building my project out of plywood.
@CuntyMcGinty
@CuntyMcGinty 4 года назад
Will always use plywood and use a trim on the face, MDF is AWFUL!!
@florentinobautista8511
@florentinobautista8511 4 года назад
I prefer to use plywood specialy birch plywood. Mdf is to dusty
@soeasytobefake
@soeasytobefake 4 года назад
Plywood. MDF is good for audio enclosures and thats about it.
@booboo8577
@booboo8577 3 года назад
The exterior MDF craze in the 90's provided a lot of work for me in the 2000's replacing it.
@vaderladyl
@vaderladyl 3 года назад
I had seen houses much older having entire areas made out of MDF including roof fascias. Unbelievable.
@Bart-Did-it
@Bart-Did-it 3 года назад
Lol we have been using MDF in New build since 1995 now it’s 99% MDF where do you work lol
@Shadowfalls89
@Shadowfalls89 3 года назад
It’s still done by unscrupulous/lazy builders and contractors. Too bad the building industry only cares about getting paid and making maximum profit. A lot of homeowners don’t know better.
@Bart-Did-it
@Bart-Did-it 3 года назад
@@Shadowfalls89 yo he don’t talk for us builders lol not all of us are bad like lawyers and estate agents and just like any other trade full of bad eggs why it’s full of clever humans not stupid monkeys lol …. Well there are a lot of them to actually now I think if it 😂
@Shadowfalls89
@Shadowfalls89 3 года назад
@@Bart-Did-it I blame the industry standards to be honest. MDF for exterior was industry standard for a while because it was cheap and maximized profit for the builders.. We later found out it was a bad idea. Similarly Masonite siding was the industry standard for a long time because it was cheap and maximized profit.. we later found out it was a bad idea.. The thing is, anyone with any understanding of those materials was leery of their adoption to begin with. I think a lot of things that are being pushed hard right now (engineered lumber, MDF, use of OSB for literally everything in a home) are going to wind up being seen as a bad idea in 10-20 years. The industry will have made their money though. I know not all contractors/builders are unethical crooks, but the industry as a whole is crooked. Gone are the days of caring about the product you create, but that's a society wide phenomenon. It just irritates me because of how expensive homes are, you would expect a product that's built to last.
@calvinbutler5517
@calvinbutler5517 Год назад
As a novice to wood working, this content is gold. I’m sure it’s useful to non novices as well, but I cant express how much confusion each of your videos clears up for a novice. Thanks dude.
@itpradeep
@itpradeep 11 месяцев назад
Well said
@janel4582
@janel4582 5 месяцев назад
Same here!
@LetsBuildThatApp
@LetsBuildThatApp 3 года назад
This didn't make much sense the first time I watched this a year ago. Having worked with both during lockdown, I can't agree with this video more.
@TheHonestCarpenter
@TheHonestCarpenter 3 года назад
Thanks for following up, Lets Build! 😄
@xyzct
@xyzct 3 года назад
"The only source of knowledge is experience." ~Albert Einstein
@flagmichael
@flagmichael 2 года назад
@@xyzct "I didn't say anything I am quoted as saying." - Albert Einstein
@Will-ge7ri
@Will-ge7ri 2 года назад
@@flagmichael “I like to wear dresses.” -Einstein
@offimoo9995
@offimoo9995 Год назад
@@Will-ge7ri “I am smarter, I am better, I am BETTER!” - Albert Einstein
@ParadoxicLunatic
@ParadoxicLunatic 3 года назад
Scroll along, I’ve got nothing useful to say other than that I really appreciate how clearly and calmly you explain everything in an unbiased, well grounded manner. Thank you :)
@Eklipze3k
@Eklipze3k 4 года назад
Sometimes I feel like the only person in the world who actually loves the layers along plywood edges, totally happy to have them on display!
@Assimilator702
@Assimilator702 4 года назад
Eklipze3k Baltic Marine Grade Birch Plywood is gorgeous!
@Guardian_Arias
@Guardian_Arias 4 года назад
i like the exposed plywood edge too, put some linseed oil on it and design the build to accentuate the contrasting laminations and the build can really pop. Box joins where hidden at one time since they where undesirable after all.
@davidelliott5843
@davidelliott5843 4 года назад
Check out the work by the guy from Greece who does a lot of cast epoxy. He cuts plywood into strips and glues them together end on. He gets “automatic” finger joints for drawers and the striped face of drawer fronts look amazing when resin sealed.
@davidelliott5843
@davidelliott5843 4 года назад
MDF can be joined by using long screws with dowels across the grain as barrel nuts or use actual barrel nuts and bolts. Ikea do this all the time where visible screw heads are acceptable and the nuts are hidden.
@Thanos0001
@Thanos0001 4 года назад
I agree. I have seem some truly breathtaking projects made with the edges in full display and if done properly and sanded smooth, they are very striking.
@Slidaulth
@Slidaulth 4 года назад
Only use mdf when 100% certain it won't get wet. Ever.
@kaikart123
@kaikart123 4 года назад
Or you can use HMR which is essentially MDF but water resistant.
@HammerNQuill
@HammerNQuill 4 года назад
I've used Medex for my kitchen doors and Extira for OUTSIDE. Very hard MDF, and water resistant. Had a sample sitting in a bucket of water for weeks before committing to the product.
@gunjeetsingh9035
@gunjeetsingh9035 4 года назад
Well thats what i was thinking!!
@chrisgraham2904
@chrisgraham2904 3 года назад
@@kaikart123 I just recently became aware of HMR. I've never seen it sold in Canada.
@mingmingdynamite3507
@mingmingdynamite3507 3 года назад
will it be ok to buy an mdf table in a fully air-conditioned room? l
@MichaelButlerC
@MichaelButlerC 2 года назад
I used to use MDF all the time for building speaker enclosures (mostly to house subwoofers in cars). Its weight was actually an advantage there, and I would still recommend it for audio speaker enclosures.
@baqoyevogabek2864
@baqoyevogabek2864 2 месяца назад
how can weight be advantage if it is installed on a car, something lighter would be more I guess better
@ML-sc3pt
@ML-sc3pt 2 месяца назад
​@@baqoyevogabek2864notice how he said for subwoofers Those put out a lot of vibration force and like recoil on a gun, the heavier the gun, the less recoil it has. You don't want your subs shaking around a lot
@Soma86120
@Soma86120 3 года назад
I really liked this video. I work at a lumber/plywood/tools hardware store (not Lowe's or home Depot it's privately owned) and to be honest this is more training on plywood than I've gotten in 4months work experience. I'm the plywood guy and I work in the plywood bay, it's just me and only me for 4 months, it's just me working there and most of the time I can help customers but every now and then I get people talking about certain things I just don't understand and this video taught me a lot more than my boss ever has. Thanks :) will subscribe to learn more
@yorgle11
@yorgle11 Год назад
I know this was 2 years ago, but I just want to say how much I appreciate somebody who wants to learn more about the product they sell at retail. Many people just get the minimum training and then stop without trying to gain more knowledge about the topic.
@CCoburn3
@CCoburn3 4 года назад
Great video. One thing that MDF is good for is jigs -- anything where you need a REALLY smooth edge.
@kaikart123
@kaikart123 4 года назад
MDF works great for pressing jig because they are not hard and distribute pressure pretty evenly.
@mikeandshanspoto5106
@mikeandshanspoto5106 4 года назад
I use it as a guide for circular saw
@paulmood308
@paulmood308 3 года назад
Or templates.
@CCoburn3
@CCoburn3 3 года назад
@@paulmood308 Exactly. Jigs, fixtures, and templates.
@AlexandraLaurineMUA
@AlexandraLaurineMUA 3 года назад
I just planning to make my first table saw jig, this comment definitely helps me what to choose. Thank you so much
@kennycoulter5525
@kennycoulter5525 2 года назад
I went to school for art, and I grew to love mdf for its smooth finish. We used it under acrylic when we would mill pieces. We would also use it for sculpture, as you can use scrap pieces that are still extremely flat, glue them up, sculpt, then cover with fiberglass resin to essentially make a very durable and heavy solid sculpture. my friend and I started making speaker boxes out of it and quickly learned about the layers splitting out.
@Rubik3x
@Rubik3x 2 года назад
I was shocked to learn that the baseboards in our new house are MDF. That was not a problem until there was a tiny leak in the utility room. The MDF swelled up and split, and then grew mold, all within a couple of months. I replaced the baseboard in the utility room with real wood.
@DrJuan-ev8lu
@DrJuan-ev8lu 5 месяцев назад
I have seen vinyl wrapped moldings which are used a lot in motor home actually disintegrate into sawdust when windows or roofs leak.
@TheMadisonHang
@TheMadisonHang 4 месяца назад
It's just nice to hear someone talk about something they know
@JorgeCanela
@JorgeCanela 4 года назад
When it comes to outdoor uses, you can get maritime-grade plywood, which is expensive, but basically impervious to water damage. And it is available in all sorts of great looking finishes.
@robertp7209
@robertp7209 3 года назад
Marine plywood is not necessarily treated for outdoor use. The glue is waterproof though. Untreated marine ply is typical and gets resin saturated in boat building to protect itself. Untreated works better with resin.
@RogerDiscombe
@RogerDiscombe 4 года назад
In the UK we have an exterior grade of MDF available. I used it for a bird feeder, the material is not very attractive but so far it is surviving.
@FrancoDFernando
@FrancoDFernando 2 года назад
I kinda like how the edge of plywood looks haha. I've seen woodworkers create furniture purposefully showing the edge, and I think it looks great!
@juanmanuelpognante2915
@juanmanuelpognante2915 4 года назад
Your explanation really answered all the concerns I had. I really appreciate your video. Thank you!
@AndricLibreSinn
@AndricLibreSinn 4 года назад
Exceptional thank you. I was thinking about learning to use MDF for some projects (some low rent rolling cabinetry for myself) and some other stuff outside. Now that I know it will only stay indoors. I can't wait to use both!
@Turn140
@Turn140 3 года назад
Literally learned carpentry from this dude. One of my favorites
@trenthardy7530
@trenthardy7530 2 года назад
🤔
@kerrygibbs8198
@kerrygibbs8198 3 года назад
I love how you present good and useful information!!! So many other videos take 15 minutes to give 5 minutes of information. Thanks!!
@bearimo2867
@bearimo2867 Год назад
This is incredbly useful information, loving your channel man, I'm learning so much!
@hackfabrication139
@hackfabrication139 4 года назад
Although you mentioned it, the dust factor needs to be really stressed when working inside. Effective dust collection and air filtration is a must. MDF dust gets everywhere. Plywood dust (or conventional wood dust), not so much. Wear a face mask when processing MDF! And keep it on for a long time after the machines have stopped. Your lungs will thank you....
@donngrimes6179
@donngrimes6179 4 года назад
Thank you-good job. I actually like making drawers out of 1/2 inch Baltic birch plywood. The exposed edges route/sand very well. The occasional void is easily filled and poly urethane provides a nice- unobjectionable finished appearance.
@vankzeng5161
@vankzeng5161 2 года назад
Hey guys! Name something that is better than FREE? We are offering FREE products including oscillating tool blades to talented people such as yourself to try out our products. All we ask in return is to provide a 4 or 5 star review on Amazon after you’ve tried it! We send you the money including tax to purchase the item on Amazon, and you try it and make the review! It's as simple as that! We have the highest quality and largest selection of adult toys that you won't get enough of! Reply Yes to to proceed.
@flagmichael
@flagmichael 2 года назад
@@vankzeng5161 I keep pushing the Yes button but nothing is happening.
@coppulor6500
@coppulor6500 2 года назад
polyurethane glue? like gorilla glue? rookie here. thanks!
@TVB-Co-Thuy
@TVB-Co-Thuy 2 года назад
So my first time here and my first impression was: He's pretty honest with the explanation. And then I looked at the the channel's name. Good work mate!
@avicohen2k
@avicohen2k 2 года назад
Never heard a better clearer explanation/comparison of the two. Thanks!
@yvesboutin5604
@yvesboutin5604 2 года назад
Great video with clear and concise explanation! I use MDF in the past to make speaker cabinets, but after I had to put some veneer or paint. With good quality plywood, I will be able to stain or varnish them to a much better looking effect. Thanks for your efforts.
@hieihachi8801
@hieihachi8801 3 года назад
plywood with glued/nailed solid wood on the edges will always be my choice.
@harshabugatti
@harshabugatti 2 года назад
Really helpful for a DIY beginner
@lindamartin830
@lindamartin830 7 месяцев назад
I am new to woodworking and I am so thankful for this video! I had no idea about the differences and you were so thorough and addressed every question I had! Thank you, thank you!
@diletomarcenaria2391
@diletomarcenaria2391 4 года назад
Nice straight forward explanation! In Brazil we use mostly mdf. They have this melamine material that comes in virtually all colors and grains designs that are just really modern looking. Since our cabinet projects include mostly straight lines and flat surfaces, just about every project is 90% mdf (white melamine for the boxes of the inside of cabinetry and wood or decorative melamine for the doors, drawer fronts, sides and so on). Oh and there are all kinds of edge tape and aluminum trim for everything also. Our sheets are very large, 6x9 or 10, but we use bigger table saws, actually I think they're called panel saws, with one moving table. One other thing, they do make this water resistant mdf (which is of this green substrate, or red for fire repellent), but still only for interior projects. Exterior mdf is available, but really expensive.
@demammoet
@demammoet 2 года назад
Makes sense. Brazil is more constant and mild weather. May as well use mdf more. Same in the Netherlands, although it's very wet it holds up in interior applications. The major thing though is American houses use a ton of wood and it's been my experience they sweat a ton to the interior in damp weather.
@muuzikk
@muuzikk 2 года назад
I’m a consumer and I am contemplating of buying a furniture with MDF. Is this a safe material? I have read somewhere that it gas off formaldehyde. Thanks
@jeremyaquino5470
@jeremyaquino5470 2 года назад
Same goes for the higher end clients in the dominican republic
@warley159
@warley159 2 года назад
@@demammoet O brasil é muito grande, tem todos tipos de climas que quiser , mas o padrão é o mesmo ... Mas quem faz o movel durar É o dono ! ... Era bom fazer um video orientando os Donos dos Moveis , por que muitos são sacanas e tentam destruir e dizer que é culpa da má qualidade do material ... Seria como usar um MDF comum na area do banheiro ... rsrsrsrs Sempre cobra pelo o que é certo , mas o cliente nunca aprova o orçamento , tendo condições ou não , opitam pelo mais barato ... chegando até no MDP, diferente do MDF
@warley159
@warley159 2 года назад
@@muuzikk vai usar o MDF em qual lugar ? compra ele laminado sempre ! , assim evita o problema com úmidade ... MDF puro sem lamina Raramente usamos ... somente máximo Estrutura ...
@erudolph
@erudolph 3 года назад
Now this is a very clear and informative video. Great job!
@DeathBYDesign666
@DeathBYDesign666 3 года назад
I got inspired to watch this by watching wood turning videos and then looking at my shelves made from mdf and wondering if they ever use that leftover material in such a way. It's fun how you go down these rabbit holes sometimes.
@paradisedreamland3
@paradisedreamland3 Месяц назад
thank you sir, every town need a honest carpenter.
@Metalbass10000
@Metalbass10000 4 года назад
I actually like to glue a thinner plywood piece to a thinner MDF piece, and generally get a nice combination of the benefits of both. Glue a decent piece of actual wood on the outer edges, and for things like shelves it's great.
@pjbconstruction8766
@pjbconstruction8766 3 года назад
Great idea. do you cover the entire sheet in wood glue when bonding them.
@Metalbass10000
@Metalbass10000 4 года назад
I've made my own plywood out of leftovers of fine, exotic and domestic, hardwoods, from my instrument building or furniture building, because I really like the look of plywood edges on certain projects.
@Denathorn
@Denathorn 4 года назад
Totally agree, it comes to another level when you glue waste ply together, then turn it on a lathe, good rub down with sandpaper (Through the grades) then coat with bees wax, it looks well!
@christophercattie
@christophercattie 3 года назад
i too thought I was the only one
@CarlosPareja07
@CarlosPareja07 2 года назад
Great video. I’m slowly learning via TouTube and found your videos to be clear and concise. Thank you.
@seanoftheroses
@seanoftheroses 3 года назад
Perfect video on these two very different products. 20 year carpenter and painter. Couldn't have done a better job explaining all this to a new guy than you, even though I know every bit of what you explained. Great video. Thanks.
@johnkelley9877
@johnkelley9877 4 года назад
I have always used either dimensional lumber or plywood due to their inherent strength. That being said if I needed a stable surface I would certainly consider using MDF. I liked this tutorial and I think you covered all of the pros and cons thoroughly. Thanks for sharing this.
@hocineted7594
@hocineted7594 2 года назад
Which is better for bedroom Mdf or plywood ?
@rolandmetayer7210
@rolandmetayer7210 3 года назад
Thank you VERY MUCH for your time and expert advice. I am a beginner DIY and the reason that I use MDF is the lower price. Furthermore, if I screw up, it doesn't cost me as much to start over. I do agree with you when you say that plywood is much stronger and that plywood holds screws much better than MDF. I really enjoyed your video ! ! Cheers from Canada,Polar Bear country.
@pradeepjhuboo9458
@pradeepjhuboo9458 Год назад
I think your video is mind-opening and reassuring. Thank you a lot indeed! I've been working with MDF for years,now next time I'm at the board seller I'll check the density of the plywoods available and seek out the least porous sides to prevent humidity seeping in. Thumbs up.
@GypsiiSOUL
@GypsiiSOUL 2 года назад
Where have you been all my life Very easy to understand and wealth of knowledge Thank you Thank you THANK YOU
@fmbjmf
@fmbjmf 2 года назад
One point worth consideration, MDF is the preferred sheet good for speaker cabinets due to higher density and lower stiffness which dampens cabinet resonances.
@LBCAndrew
@LBCAndrew Год назад
High end speakers use baltic birch plywood, usually with a veneer.
@adamcoe
@adamcoe Год назад
MDF is the preferred *inexpensive* sheet good for speakers. As LBCAndrew rightly points out, Baltic birch ply has been and continues to be the standard for speaker enclosures of a serious calibre.
3 года назад
It would be nice if you "updated" this video with an "MDF vs OSB vs plywood" video.
@oldfart269
@oldfart269 3 года назад
I agree. Or, do an MDF vs. OSB video.
@lightbulb1982
@lightbulb1982 2 года назад
@@oldfart269 Apples and oranges. Nothing to compare too
@oldfart269
@oldfart269 2 года назад
@@lightbulb1982 MDF and OSB are both produced from wood by-products. MDF is sawdust, glued and compressed. OSB is wood chips, glued and compressed. Both are used for various construction purposes, but I would take OSB over MDF if I had a roof to replace, or subfloor to put in. Appearance wise, I would consider MDF for shelving, if I had to put in a shelf for low stress use. OSB doesn't offer the visual appeal.
@tihroflan
@tihroflan 2 года назад
@@oldfart269 I actually disagree, I quite like the "rough" vibe you can get with natural osb.
@mattstegall
@mattstegall 2 года назад
I really don’t think OSB belongs in this comparison. OSB is really for rough carpentry not interior shelves, cabinets or built-ins.
@ramart06
@ramart06 3 года назад
Thanks for your opinion. I enjoy building speaker cabinets and my no. 1 choice is Birch plywood for its looks and sound quality when properly braced.
@wonttakethewidepath7851
@wonttakethewidepath7851 3 года назад
Once again, incredibly helpful for a purchase decision I’m making. A cabinet constructed of MDF that will remain inside. Thanks, you’re pretty awesome!
@steadyeddie7453
@steadyeddie7453 2 года назад
Just my opinion but I have found that the biggest advantage of MDF is that it perfectly flat and void of defects. So you get the entire sheet to work with, and you don't have to work around knots and voids. I have made many jigs using it, and my table saw extension tables are doubled up 3/4" MDF covered by a plastic panel material, making cutting sheet goods a breeze. And when it comes to fastening I try to incorporate dados, rabbets, and grooves to help support the material. Then glue and screw as usual. And if you are really concerned, Confirmat (RTA) screws are made specifically for MDF. Good video, thanks.
@thefirestarterpack4235
@thefirestarterpack4235 2 года назад
One use of MDF where it has an advantage over plywood is in speaker cabinets. Either for household or vehicle use. It does a much better job of minimizing cabinet vibrates and has been a great budget option for speaker enclosures.
@achannelhasnoname5182
@achannelhasnoname5182 Год назад
The acoustic advantages of MDF over plywood are barely measurable, let alone hearable. I still prefer using plywood for speaker cabinets, as you can simply oil or stain it.
@hamishmctiaigh4363
@hamishmctiaigh4363 Год назад
Straight to the point, no nonsense, all meat and potatoes, big thumbs up to you mate! Really appreciated
@esotericone9101
@esotericone9101 Месяц назад
This video is exactly what I needed!! Thank you❤
@andabien3
@andabien3 3 года назад
Information dense: I appreciate that.
@AllenFarms
@AllenFarms 4 года назад
I use mdf for panels on painted cabinet door panels with maple rails and styles gives smooth finish after priming, for stained cabinets they have mdf core maple which provides stable panels
@geraldoutdoors245
@geraldoutdoors245 Год назад
Just found your channel great content for us beginners, keep up the great work.
@jhh243
@jhh243 3 года назад
Great advice!!! Thank you for taking the time to do these videos. Subscribed
@cedr777
@cedr777 4 года назад
Holy shit, I never knew they had so much difference with each other, thanks a lot!
@throwachair
@throwachair 3 года назад
spot on, mdf is for interior, mainly decorative work
@tylocke709
@tylocke709 2 года назад
This video is great! Clear, concise and interesting
@write2nick
@write2nick 3 года назад
Thank you for sharing your knowledge and safety tips. I’m so grateful.
@alternatesportshistory3605
@alternatesportshistory3605 4 года назад
Thanks for the video--answered a lot of questions that I wouldn't have known to ask. My current project is a snooker table (and because I'm building it cheap, slate is out of the question), and because of its flat surface and tendency to resist warping, I'm planning to use MDF, so I really appreciate your discussion on what you can and can't do in working with it. Thanks!
@birdlady2725
@birdlady2725 2 года назад
Just don't spill drinks on it, and you should be good!
@pferoxtheskeeterguy
@pferoxtheskeeterguy 3 года назад
I live on the Texas Coast, so humidity is always high, even with painting, MDF doesn't seem to last long and will start to swell after a short time.
@pantha4pantera
@pantha4pantera 3 года назад
Yes, same thing here in New Zealand, the humidity alone turns the MDF into Weetbix. I suppose you would need to run a dehumidifier constantly if one wanted to use MDF. I avoid MDF at all costs!
@thispandaispurple
@thispandaispurple 2 года назад
I live in Ontario, and even here the humidity messes up MDF, if you live near a lake or something. Largely switched to OSB here.
@urmommabear5monthsago
@urmommabear5monthsago Год назад
Finally someone speaking regular English. 🙏🏼
@gregjohnson8486
@gregjohnson8486 4 месяца назад
I'm a recent subscriber to your channel. Although I'm an amateur woodturner, I have learned a lot about wood and building materials, certain tools, and do's/don't from your channel. Thanks so much for sharing! 👍🏾
@vikassm
@vikassm 4 года назад
Awesome video! In addition, Regular wood and Plywood sawdust and chips (even treated grades) can be discarded in your garden as a decent soil amendment. Degrades nicely over time and holds some extra moisture for your plants. MDF dust on the other hand, is a complete no-go for plants and earthworms. Speaking from experience 😁
@jeetendrajagwani
@jeetendrajagwani 2 года назад
Wow that's a new one for me...thanks!
@ronmack1767
@ronmack1767 4 года назад
Enjoyed the video Ethan. That was interesting.I'm more old school since I'm older anyway. Never used MDF much at all. I have replaced allot that was used for trim on the exterior of homes. I have some on my on outside storage buildings that needs replacing now. Y'all stay well, take care and God bless.
@TheHonestCarpenter
@TheHonestCarpenter 4 года назад
Thanks Ron! I've done tons of that same MDF trim replacement. Crazy how many houses out there have it.
@cdamarshall5127
@cdamarshall5127 2 года назад
Very good info and the presentation is EXCELLENT !
@917Stefano
@917Stefano 3 года назад
This is an excellent video! You answer all the questions. Lot of good info here.
@josephting-zk8ob
@josephting-zk8ob 3 года назад
Excellent review. Extremely informative and technical too. Keep up your good work. Due to climatic reasons at equatorial region with humidity around 70% to 80% most of the time, I prefer solid hard wood. Thanks you very much. Really enjoyed your video.
@garethbaus5471
@garethbaus5471 3 года назад
How does marine grade plywood hold up? It isn't generally rot resistant but it shouldn't fall apart.
@BrainFizz
@BrainFizz 3 года назад
Pros and cons to both. It mostly boils down knowing the limitations and characteristics of the material. MDF is an amazing product when used properly. You can easily get a full 8’ span in MDF without sagging, just a torsion box with 12mm MDF and 18/25mm internals. Edging is easily overcome with paintable edge banding. Dust is the biggest drawback , MDF dust is cancenogeic (probably next generation asbestos), But is stable, paints well. Machines well. Bottom line, you can do great long term high end jobs with it. If you know your trade.
@CryptikStudios
@CryptikStudios 2 года назад
*carcinogenic
@hocineted7594
@hocineted7594 2 года назад
Which is better for bedroom Mdf or plywood ?
@stephenandelin4688
@stephenandelin4688 2 года назад
Covered everything I needed to know,brilliant video, thanks James.
@lusther3385
@lusther3385 2 года назад
I came here to look for information about the best one to use, since I’m renovating my room and Im kinda in a small budget so this really helps . Thanks.
@davehofmann4601
@davehofmann4601 4 года назад
Totally agree with everything you just said. I'd just like add from out of bounds that many of the similar down falls of the MDF also exist in the OSB realm. I don't care how much they want to sell that it's engineered. In a few years it has the same moisture problems as MDF. Whether inside out out.
@TheHonestCarpenter
@TheHonestCarpenter 4 года назад
Yep, pretty much anything with glue, Dave. OSB they at least have some grades with acceptable weather exposure time frames (it's printed on that stamp on OSB sheets). But, given enough moisture, it'll just peel to pieces.
@eman0828
@eman0828 3 года назад
Arogsy Console uses MDF and their professional console desks hold up well for years. Theres people using the same console desk for 15 to 20 years. MDF is pretty much the standard in all high end studio furniture.
@johncoops6897
@johncoops6897 2 года назад
Just apply a sealant to the MDF or OSB or Chipboard or any other wooden composite material. You really should seal plywood too, if you don't want it to delaminate, warp and split. It's not rocket science, sheesh!
@hocineted7594
@hocineted7594 2 года назад
Which is better for bedroom Mdf or plywood ?
@The_RC_Dude
@The_RC_Dude 3 года назад
Thanks James, I, not in a situation where I need to choose between the two materials, but I'm a,ways up for more knowledge about carpentry. I'm going to be building an MTB (Mountain bike) kicker/jump out of wood soon for myself (I've made several simpler ones with my neighbor), and I'll beep using thin plywood for the sides, as well as top and bottom, and I'll use 2"x3" for the "ribs" of the jump. I don't like how MDF turns into that "toxic dust", I definitely don't want to breathe that stuff in. I'm just going to steer clear of the stuff, I don't do much sod working at all, mostly just at really small scales. Another thing is, for my ramp, it's going to be curved (this way you can really get a good pop off the lip, and hone in your jumping technique), and plywood is, well, ,ore playable then other options. I might soak the plywood before screwing it onto the ramp, as this will make it more flexible and less likely to crack.
@gregstephens1103
@gregstephens1103 3 года назад
Just worked with MDF for the first time. Built a shop cabinet. Finished product looks great, BUT was very difficult to put together. Went with using dowels as the fasteners AND my god finished product was Heavy to get in place. Appreciate your video and channel, I am a novice and certainly appreciate the advise/instruction and comments.
@clarkjanes3094
@clarkjanes3094 3 года назад
Soon I'm going to make a small work table for small wood projects. It sounds like MDF would be a great choice for the work surface: heavy and very flat. Thanks for the video!
@edbianchi8839
@edbianchi8839 4 года назад
Very good comparison. In my case, being 81 years old, you miss to mention the heavy weight of something made of mdf vs play wood
@tsnstt
@tsnstt 3 года назад
He did mention it in the video
@jackflash5659
@jackflash5659 4 года назад
Thank you for the helpful info. Starting some DIY projects and will be using both products.
@andrewkrieger1736
@andrewkrieger1736 3 года назад
Good profile pic
@kevinlamarr1424
@kevinlamarr1424 3 года назад
Great pro/con video! I’m restoring a 1984 Winnebago and was looking at the difference between the two. I’m doing the roof and floor so I’m going plywood. Thanks
@hananafarheen3958
@hananafarheen3958 2 года назад
Thank you so much for this video.. Answered a lot of my questions.. Thanks again..
@MrPoilleke
@MrPoilleke 3 года назад
As a skateboard builder l use maple veneers, l glue myself, so actually l make my own plywood :) l just love it
@TheHonestCarpenter
@TheHonestCarpenter 3 года назад
That's cool, Pascal! Maple is a great hardwood--pretty too :)
@MrPoilleke
@MrPoilleke 3 года назад
@@TheHonestCarpenter yes indeed! And with every purchase, l buy a tree planting for less than 1€...take care!
@JonMcClainMusic
@JonMcClainMusic 2 года назад
Wow. You are so knowledgeable, and you convey that information very well. Well done.
@grahamcurran8744
@grahamcurran8744 3 года назад
Awesome video learned alot. Been watching alot of your videos since I tidyed up shed. Quality thanks bro
@mariokarter13
@mariokarter13 2 года назад
Meanwhile I'm over here unable to tell Oak from Pine from Maple from Cherry and so on.
@sandrafurtado7484
@sandrafurtado7484 4 года назад
Plywood is always my choice over MDF. Great video! Take care
@TheHonestCarpenter
@TheHonestCarpenter 4 года назад
Thanks Sandra! 😄
@zinnaleonie6687
@zinnaleonie6687 2 года назад
Informative and very helpful, i learn one words from this video, which is work around its limitations. Its really helpful
@javismc7099
@javismc7099 Месяц назад
Now I know when I need plywood or MDF. this explanation was so precise and simple yet detailed. Thank you so much
@fishrrelaxing9361
@fishrrelaxing9361 4 года назад
I really like mdf.. even better if you can find it hdf.. I just wish it wasn’t so heavy! For smaller projects I go mdf. For larger ones I’m going to have to move and install I go plywood. But the final finishing if mdf is sooooo much easier and faster then plywood. Long as you edge band the mdf with plywood like say a face from for a cabinet.. I’ll build the cabinet from mdf over plywood all day. But then an upper unit I’ll build from plywood and then use mdf for doors and drawers if doing something like raised panels cause it finishes and shapes so nice. I also like the fact that mdf comes oversized so you actually get what you’re paying for as well as getting a true 3/4” thickness so layouts and measurements are way faster and easier. The last thing is I tend to screw plywood together where mdf I use a lot more brads and finish nails.. especially around the edges. When I can I’ll get some hdf for these areas as it will hold a screw even better then ply to the point if you don’t ore drill you’ll snap the screw head off every time. If you’ve never tired you can stain mdf.. not the same way but you can get some interesting looks and finishes with it. Shellac makes for a nice finish on mdf actually but a lot of your clearish finishes take nicely to mdf and give a really unique look. Like an odd brown marble counter top top look lol
@jacobkomnath7961
@jacobkomnath7961 4 года назад
when i cut ply, i tend to put painters tape over the area im gonna cut to prevent tearout. also just cut it slow helps too.
@chestnut250
@chestnut250 4 года назад
Also, if you're cutting it on a table saw, you may want to get a zero clearance insert to prevent the tearout.
@redmatrix
@redmatrix 4 года назад
Same
@chuckschillingvideos
@chuckschillingvideos 3 года назад
A couple of other things help too. First, get the right tablesaw blade. Don't use just any old crappy combination blade you pick up at HD or Lowe's. Get a good Freud or Forrest high tooth count combination carbide tipped blade. Clean it frequently. And by frequently, I mean after every occasion where you saw plywood or MDF or relatively green lumber. I even go so far as to wax my tablesaw blades. Then again, I live in an area of extreme humidity so I have to in order to prevent rust. But it's a good idea for any woodworker with the time./inclination.
@angelafox4380
@angelafox4380 3 года назад
Excellent info!!!! Truly enjoying your knowledge ☺️☺️☺️☺️
@potatopack
@potatopack 2 года назад
What you say is exactly my thoughts. As usual you are wise and just know how to present views wonderfully. KEEP IT UP
@seanmccaffrey6378
@seanmccaffrey6378 3 года назад
In the uk we have moisture resistant and for higher quality hdf (high density) which machines much better
@yosemitesam4549
@yosemitesam4549 4 года назад
I agree, MDF has fewer uses than plywood.
@Cybergrip1
@Cybergrip1 6 месяцев назад
Excellent review. Thanks.
@jpdenat1
@jpdenat1 3 года назад
Nice and simple to understand video > keep on the good works
@michaelwright6742
@michaelwright6742 3 года назад
I built a table saw cabinet out of MDF. I radiused the edges and filled the edge pores with drywall compound. Sand, spray prime and spray paint and it can be mistaken for formed steel. It comes out very smooth. I also like the added weight for holding my table saw. Great video!
@hocineted7594
@hocineted7594 2 года назад
Which is better for bedroom Mdf or plywood ?
@MonkesReturn42069
@MonkesReturn42069 4 года назад
I'm a young painting contractor, and though I haven't spent a lot of time building, I am exposed to a lot of renovation work. I agree with you in the sense that plywood is better than mdf is almost all situations. MDF is amazing for both floor and door trim, and works really well when applied as cleats for shelving. It finishes is extremely well, and can be really durable when paired with sturdier finish coats. (Such as Benajamin Moore's Advance line) One application I see MDF used that I would highly recommend NOT using it for is shelving. Although it finishes really well and is durable, after several years MDF will start to sag/bow in the center of the shelves. Otherwise it can be a really amazing trim product, and would still highly recommend it for anything non-structural such as shiplap!
@chuckschillingvideos
@chuckschillingvideos 3 года назад
Yup. It is inevitable/axiomatic that an MDF shelf will droop over time. Even if you never place anything on it, MDF cannot support even its own weight.
@hocineted7594
@hocineted7594 2 года назад
Which is better for bedroom Mdf or plywood ?
@martinmoore4401
@martinmoore4401 2 года назад
Great video. People need to understand they are compromising on quality and durability when they buy cheap furniture.
@rajaramanv
@rajaramanv 3 года назад
Great summary, thank you. It was useful in making a choice for my new home.
@thomaslee8116
@thomaslee8116 4 года назад
Honestly, I like the way that MDF looks for a painted project, but the dust problem is a real barrier to using it.
@TheHonestCarpenter
@TheHonestCarpenter 4 года назад
It does paint really well, Thomas. I use 1x2 pine trims to screen it, and the whole thing comes out looking very uniform. But I try to not to rip down full sheets--I just go with half sheets as much as possible, or the longer 11-7/8 pieces. That cuts out a lot of the dusty work with the table saw😪
@crimson777king
@crimson777king 4 года назад
@@TheHonestCarpenter You can get moisture resistant and fire retardant MDF and dust extraction is advised with all timber and MDF cutting and sanding. The moisture-resistant green MDF boards are excellent for fine routing and detailing/finishing. Even better is the fibralux Black HDF.
@chrismoore9997
@chrismoore9997 4 года назад
@@crimson777king - what store in the US sells those items?
@tomlee432
@tomlee432 3 года назад
I've been building with wood my entire life. The only thing that I have found mdf is good for us flight cases for instruments. That's all I really use it for. Plywood is a great building material. I use osb sparingly. Too many woodworkers opt for easy. They also seemed to have forgotten how to bend wood. The one thing I've noticed in over 50 years is the rise in black mold. Osb and the like do not have the natural defenses even plywood has. It turns to crap pretty quickly when exposed to moisture. They have their use, in very limited places. My dad was an amazing woodworker and he would laugh at that stuff. He said you use a tree you get the strength of a tree. You use wood scraps you get the strength of scraps. You use saw dust you get the strength of saw dust. Chips and saw dust went into a barrel. It was used to start bon fires.
@MOAON_AABE
@MOAON_AABE Год назад
Damn ,I just built my first work bench in my garage with a mdf surface so I could have it super leveled for working, do you think that was a mistake?
@xeren45
@xeren45 Год назад
@@MOAON_AABE nope, mdf is a good material for bench tops. Even festool uses it for their bench
@MOAON_AABE
@MOAON_AABE Год назад
@@xeren45 that makes me feel so much better about my decision, thanks for sharing that with me
@thomaskletzl6493
@thomaskletzl6493 2 года назад
really nice video i always use mdf for building speaker boxes most of the time 38mm tickness
@Gig2Dave
@Gig2Dave 2 года назад
Thank for clearing that up. Great video.
Далее
PVC TRIM VS. WOOD TRIM? (Pros And Cons!)
11:23
Просмотров 892 тыс.
TRY NOT TO LAUGH 😂
00:56
Просмотров 9 млн
Rare Mbappe Moments 🤯
00:21
Просмотров 2,9 млн
Танцуем с ЛПшкой 😂
00:14
Просмотров 413 тыс.
I was wrong about MDF...
16:14
Просмотров 990 тыс.
Buying Kitchen Cabinets - Beginner's Guide
14:20
Просмотров 225 тыс.
Painting Cabinets | Get a Smooth Finish on MDF
8:46
Просмотров 474 тыс.
Testing MDF vs Plywood - What to Buy?
22:54
Просмотров 696 тыс.