Mechanical seal installation in Glass lined Reactor

Подписаться 7 тыс.

Просмотров 25 тыс.

50% 1

In this video procedure for mechanical seal installation in Glass lined reactor.
glass lined reactor seal area damaged so repairing done and PTFE sleeve and Hastalloy sleeve shrik fitted.
before installation 3 parameters required to be check to avoid seal failure. For this Dial gauge , puppet Gauge , gauge clamping kit , filler Gauge required.
in this video 3 parameter Run out of shaft , Squareness of pad plate and concentricty checked.
Mechanical seal installation with all parameter • Mechanical seal instal...
Mechanical Seal installation with Run out parameter • Mechanical Seal instal...
Double Mechanical seal overhauling • Double Mechanical seal...
Single Mechanical Seal Overhauling • Single Mechanical seal...

Опубликовано:

21 авг 2021

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 69

@kirangohil7156 11 дней назад

Ak number modi saheb.

@kamleshvasava3074 8 месяцев назад

Very Nice sir

@anilpal5947 Год назад

Really thank full sir very knowledgeable video for every mechanical engineering

@karannsolanki4933 Год назад

Thanks you bhoumik sir.

@dharmeshpatel-zc1jz 2 года назад

Well explained and interesting, Informative video... All doubts clear in this one video...👌👌👍👍 Keep it up...

@bhaumikModi09 2 года назад

Thanks

@shaileshgolwala6396 Год назад

Very nice

@argohil6734 Год назад

Sir pls ek bar pad plate ke niche Jo gasket rakhte he uska swiming karke dikhao na

@pankajpatel6640 2 года назад

Good job nice video

@sandiplimachiya4306 2 года назад

Very important & useful information sir, thank you

@akshayrana5296 2 года назад

Very informative

@bulusahani4064 2 года назад

Execelent video sir thankyou

@rakeshparmar942 2 года назад

Thanks sir making this video

@kunalsonar123 2 года назад

Very good and informative

@bhaumikModi09 2 года назад

Thank u

@diputiwari4056 2 года назад

Thank you for very informative vedio, my all doubt clear now,once again thank you so much sir.

@bhaumikModi09 2 года назад

Hi... 500 subscriber ke baad me double mechanical seal calculation video upload karinga... To jaldi friends k pass subscribe karado

@bariyajigna5471 Год назад

Good information sir

@sanjaypatel7562 2 года назад

Thank you sir

@bhavnasindha3562 2 года назад

Thanks

@dhirengohil8398 Год назад

🙏

@shiva.dhangar9999 2 года назад

Thank you sir for the video....

@bhaumikModi09 2 года назад

Thank u Watch another video

@vishalprajapati932 2 года назад

Good sir

@mahendradhawalkar925 2 года назад

Very nice sir thanks for sharing this information

@bhaumikModi09 2 года назад

Thank you... Share more..

@vaibhavbhosale3705 2 года назад

Thank you... well defined

@bhaumikModi09 2 года назад

Thanks

@roshanthombare2690 2 года назад

Very informative sir 👍

@bhaumikModi09 2 года назад

Thank u

@krishnaautogarage2274 2 года назад

Thanks 🙏🙏🙏🙏🙏 sir

@rambabubuttala7660 2 года назад

Sir please share a reactor fully breakdown video

@dhirengohil8398 Год назад

👌

@karannsolanki4933 Год назад

Sir reactor wetar leveling ka video

@HardikPatel-ut3bv 2 года назад

Sir boj mast video bo sikhva mle tamara video joy ne

@bhaumikModi09 2 года назад

Thanks

@luicywilde8785 2 года назад

Where can i find this puppet dial holder?

@SandeepPrajapati-xl7ye Год назад

Seal me kon kon se parts hote he uska list bhejo vidio me ny dikh raha he

@nilashthakur7206 2 года назад

Nice video sir

@Ghoda144 2 года назад

Sir ye concensity stage me puppet dial gauge ka pointer kis pe set karna hota he aor squreness me

@bhaumikModi09 2 года назад

Squareness me pad plate ki surface pe point rahega... And concentricity main pad plate ki side ki wall pe

@kalpeshsoni9075 2 года назад

Hi sir reacter seal perameter ke aur video shere karna

@taggedeleeee5407 2 года назад

Can you explain seal setting point for agitator. It will be very useful to us ji.

@bhaumikModi09 2 года назад

Seal setting point ??

@MohanPatel-gp6qi Год назад

भाई Squarnes pera मीटर maines में होता है या plush में Squarnes का pera metar puppt gauge se nikala जाता है run out check mai maines में रहेगा या plush में

@bhaumikModi09 Год назад

Sab reading plus me aana chahie

@ASHISHGUPTA-uc7kj 2 года назад

Runout kaise set karenge by tightening of coupling.please explain

@bhaumikModi09 2 года назад

Like pumpa lignment... Keeping washer or tightening bolt properly

@siddharthnizama8343 2 года назад

Squarnes,run out and conscity kitne mm tak chalta he

@bhaumikModi09 2 года назад

Runout : 0.08 mm Concentricity & Squareness :0.10 mm

@fatesanggohil9343 Год назад

ખૂબ સરસ જાનકારી

@Bkfitness_ 2 года назад

Iam 100%statisfied sir

@pareshparmar151 2 года назад

Ped gasket kis material ka Bana huva HOTA he

@bhaumikModi09 2 года назад

PTFE envelope Gasket

@krushnpalgohil2967 Год назад

sir which type of gear box and coupling use in glr?

@bhaumikModi09 Год назад

Helical gear box and muff coupling

@krushnpalgohil2967 Год назад

@@bhaumikModi09 thanks bhavesh bhai

@krushnpalgohil2967 Год назад

bhaumik bhai

@tolapiramana4419 2 года назад

Seal service what tipes used o rings

@bhaumikModi09 2 года назад

Kalrez oring, PTFE wedge ring, Neoprene Rubber o ring

@tolapiramana4419 2 года назад

@@bhaumikModi09 tq sri

@asifchaudhary9938 2 года назад

If the shaft is tight on the top of the sleeve shaft, then if the shaft is down, then the sleeve will also be up and down, sir

@milinddhopavkar8499 2 года назад

Sir, We are starting with radial run out, Then sqareness and finally concentricity. If I am going adjust concetricity then there is chance of disturbance for radial clearance. Is then necessary to do radial, sqareness adjustment again? Please reply. Thanks

@bhaumikModi09 2 года назад

In this video started with Runout

@bhaumikModi09 2 года назад

Yes necessary to do again

@milinddhopavkar8499 2 года назад

Thanks sir 🙏

@krushnpalgohil2967 Год назад

this is which type of mech.seal??

@bhaumikModi09 Год назад

Cartridge type Single mechanical seal