Mercury 2.5 Small Outboard Motor Impeller Replacement

Подписаться 66 тыс.

Просмотров 29 тыс.

50% 1

Replacing the impeller in a Mercury 2.5hp 2 stroke outboard motor. The Mercury water pump impeller in these small outboard engines can be hard to change or they can be very easy to do like this water pump impeller in my little Mercury two stroke. This 2.5 Mercury two stroke outboard might be exactly like or similar to the impeller in a Mercury 3.5 hp outboard and has a simple impeller setup that is very easy to replace.
It took about 10 minutes with two simple hand tools to change the impeller in this little outboard motor. In this video I show you step-by-step how to DIY this important maintenance task for your Mercury (or possibly Nissan or Tohatsu) outboard.
Buy Permatex Threadlocker (blue) here: amzn.to/38XMHgB
Buy the impeller I used in this video here: amzn.to/36tSqKe
(check to make sure this one is right for your application!)
As an Amazon Associate I earn a small commission from qualifying purchases.
Here's the link to the Mercury Parts catalog - www.mercurymarine.com/en/us/p...
00:00 Introduction
00:16 How to find the correct impeller for your Mercury outboard engine
01:17 Removing water pump impeller from my 2 stroke Mercury 2.5 outboard engine
06:52 Installing a new water pump impeller in my Mercury 2.5 two stroke outboard motor
❤️ Subscribe to my RU-vid Channel / waynetheboatguy
📷 Follow me on instagram! / waynetheboatguy
☞ Follow me on TikTok! / waynetheboatguy
▶︎▶︎▶︎Playlists About Boats
🚤 Tiny Boat/Jon Boat Stuff • Tiny Boat - Little Boa...
💰 Boat Shopping • Boat Shopping
🐋 Boston Whaler • Boston Whaler Videos
🛥 Boats, Boat Trips & Boat Accessories • Boats, Boating Trips, ...
⚡️ Electric Boats & Electric Boating • Electric Powered Boats...
🛶 Kayaks & Kayaking • Kayaking & Kayak upgrades
🪦 Curtis Creek Maryland Ship Graveyard • Curtis Creek Maryland ...
🎲 Boating Shorts • Boating Shorts
▶︎▶︎▶︎Boat Engines & Motors Playlists
⛽️ 2 Stroke Outboard Motors • 2 Stroke Outboard Engi...
⚙️ Volvo Penta Maintenance & Repairs • Volvo Penta Maintenanc...
🌎 Newport NT300 electric outboard • Newport NT300 3 hp Ele...
🚽 Evinrude 2 - 2 hp engine • Evinrude 2 - old Evinr...
🔒 Seized Suzuki DF20 • Suzuki DF20 Short Shaf...
🔧 Inboard/Outboard Maintenance • Inboard Outboard (Ster...
▶︎▶︎▶︎ Boat Repairs & Projects Playlists
🛠 Low Cost Boat Repairs & Projects • Low Cost DIY Repair & ...
🔨 Boat Transom Projects • Boat Transom Projects
🧰 Boat Repair & Maintenance • Boat repair, maintenan...
🛞 Boat Trailer Projects • Boat Trailer Repairs &...
▶︎▶︎▶︎New Boater Playlists
📌 Boating Education & Tips • Boating Education and ...
📓 Boating Basics • Boating Basics for New...
🆘 Boat Safety • Boat Safety - videos t...
❄️ Boat Winterization • Boat Winterization
#outboardimpeller #replaceimpeller #newimpeller
Sound effects and additional music is copyright free from iMovie

Развлечения

Опубликовано:

1 авг 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 41

@WayneTheBoatGuy 2 года назад

After I changed the impeller, I started this motor for the first time in 6 months. If you would like to see how it goes, it is included in this video: ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-A9kzfzt4C5o.html

@WestonSuperMan 2 года назад

When I started messing with boats.. I spent £120 for someone to change a impeller on a outboard.. So videos like this are very handy too new boater to show that some jobs on outboard are easily done at home.

@WayneTheBoatGuy 2 года назад

Thanks! Your Seagull doesn’t use have one does it?

@WestonSuperMan 2 года назад

@@WayneTheBoatGuy they have an impeller but its not a rubber 1.. its like a porcelain square which doesn’t touch the sides.

@allenjenkins7947 Год назад

Thanks for the video. I changed one once a few years ago, but I needed a refresher. Yours was the first useful one which popped up. I find that they tend to dry out and go brittle with lack of use, rather than wearing out. I've had that problem with a Yamaha 70 as well.

@jackie87430 Год назад

I think I just learned why my new-to-me engine is overheating, awesome video! Subscribed to your channel :) keep up the great work sir

@WayneTheBoatGuy Год назад

Awesome! Thank you!

@user-cq5no6hk2o 9 месяцев назад

Looks same as in Suzuki DT2/2.2. Super easy to change. Just rotate it clockwise while pushing it into place until it clicks into pin.

@youdonthavetoreadthispost.5850 Год назад

Spot on once again Wayne. If you do nothing else do This! 3 minutes to a smoking engine.

@DinghyCruisingKingfisher Год назад

Thanks for the video. Very helpful.

@WayneTheBoatGuy Год назад

Thanks for the kind words!

@cwmaxfield2000 Год назад

Wow You just sold me on this Merc

@kevinmccarey5015 2 года назад

Hello Wayne, Great. video

@WayneTheBoatGuy 2 года назад

Thanks!!!

@calom4823 2 года назад

I just buy a old beat up one , run realy great .

@c130king Год назад

Great video...THANKS! Do these small 2.5HP Mercury outboards (I have one just like the one you are changing impeller on) need oil change for lower unit? Any tips/advice on on how to do that? Thanks again!

@WayneTheBoatGuy Год назад

Yeah the oil in the lower unit should be done annually. I don’t have a video on that… yet but soon!

@MrRobinski 2 года назад

Can you store this motor lying down or is it best to stand upright?

@WayneTheBoatGuy 2 года назад

I try to keep my motors upright, but many can be stored on their side.

@terrysmith8714 2 года назад

yes, many times.

@grahamgeorge1130 2 года назад

have you got a video of how the lower leg goes please many thanks

@WayneTheBoatGuy 2 года назад

I do not have a video of that - hope you can find what you need from maybe some explosion view diagrams on the Mercury parts web site.

@msf60khz 2 года назад

When I did this I did not know which way to turn the fins?? could not work it out

@WayneTheBoatGuy 2 года назад

Apparently the fins will usually reset themselves if you have them in the wrong way.

@juliodelarosa9554 Год назад

Hola tengo un Sears Samsung de 3.5 caballos el impele que tiene no sirve dónde puedo conseguirlo he ido a varios lugares y no lo hallo aquí en República Dominicana

@deanfrei8765 10 месяцев назад

Hey Wayne love the channel, is the impeller in the same place on the 3.3 as it is on the 2.5?

@jonathanjadotte 9 месяцев назад

That's what I'm wondering myself, any luck?

@steinhytland2593 8 месяцев назад

If the motor has a shifter and a neutral, the pump sits above the gear housing. This needs to come off. Lining the shifter link back up is very tricky.

@jonathanjadotte 8 месяцев назад

@@steinhytland2593 u can say that again! did mine about a month ago. I used a tiny stick to hold it in place as I used my ratchet in my other hand to tighten 🤣

@steinhytland2593 8 месяцев назад

It should be emphazised that this prosedure only applies to non gear models. Impeller on the propeller shaft only pumps and cools with propeller turning. Many of the Mercury/Mariner 2.5 and 3.3 engines has a shifter and a neutral. The procedure is very different and more complicated. Different impeller to. I won't try to describe it here, but issue one warning. Don't start by undoing the shaft housing like Wayne does. Look up the proper procedure.

@claytonshuntingandfishing Год назад

That’s mine was completely coming a part

@PapaMav Год назад

I am currently on my 3rd or 4th impeller replacement on my 2cyle 8HP Mariner while also replacing the seals in the lower unit, so I also have the prop shaft out and apart. However, bc I ordered the impeller from JINGZU on AMAZON, my project is stalled. As the case with typical Chinese knock off parts, while the impeller from them looks like an exact replacement, the inside diameter tolerance of the replacment impeller is too tight and won't properly slide on the 1/2" drive shaft. On the plus side, no issue getting a return label from AMAZON and prompt $4.25 full refund from JINGZU. Then went to EBAY to order a genuine Mercury/Quicksilver impeller. (The JINZU had the same exact part # as the Quicksilver). -I doubt they make cotter pins out of aluminum as it likely breaks easier bending it back and forth, unlike SS -That was not a screw driver you used w/the 10mm socket; that is called a Driver Spinner

@WayneTheBoatGuy Год назад

It seems to be hit and miss with marine and car parts these days!

@PapaMav Год назад

@@WayneTheBoatGuy part of our cost wanting most everything built cheaply for us in China.

@PapaMav Год назад

@@WayneTheBoatGuy I do also douse the impellers with Armor All and grease the key and the plate and washers they ride on.

@bullyakker 2 года назад

Need an inexpensive impeller that's nearly impossible to find? FInd someone with a 3d printer.. 4+ different materials can be used. Been 'tuning' trolling motor props for 1) more mileage 2) more speed 3) both. so far? I've got more work to do but gained 1MPH and lost 10 minutes with 115AH APG Battery so.. think I'm onto something good.

@WayneTheBoatGuy 2 года назад

Sounds like fun projects!

@onthegowithgreggsavage 14 дней назад

Nobody on this or any site has half an ounce with common sense to put a mirror in there, 2H. P water impeller change cause every time. I type that up I get a 2.5 or a taihatsu. Nothing explaining how to slide the lower unit off which is stuck. I wish somebody would have enough brains to do that. Post a mariner two h p a two stroke.There's plenty of them out there

@onthegowithgreggsavage 14 дней назад

Mariner two h p even voice texting sucks