MICTUNING 8 Pod Rock lights in the RZR PRO XP. Are they any good? Unboxing, install, and review.

Подписаться 8 тыс.

Просмотров 14 тыс.

50% 1

Today I'm unboxing the MICTUNING C1 8 Pod Rock Light system and installing it on the 2020 Polaris RZR Pro XP. Let's get to work!
If this video helped you, please give me a thumbs up and consider subscribing. Thanks for your support!
Rock Lights:
www.amazon.com/gp/product/B07...
Solder Seal Wire Connectors (pretty much the best thing ever):
www.amazon.com/gp/product/B07...
Wirefy Female Spade Connectors w/ Heat Shrink:
www.amazon.com/gp/product/B07...
Relay:
www.amazon.com/ONLINE-LED-STO...
Polaris Pulse Bar Connector:
www.amazon.com/Pigtail-Connec...
Fuse Holder:
www.amazon.com/SIM-NAT-Automo...
Disclaimer - this video is for entertainment and informational purposes only. Do not attempt. Attempts to recreate, reproduce, or replicate anything seen in this video is done at your own risk. As with any product, it should only be serviced by the manufacturer or a licensed professional. Tampering with your product may void your warranty. Video owner shall not be held responsible if you void your warranty. The video owner will not be liable for any damage or injury incurred by anyone to anything while trying follow the steps in this video. Any and all liability to any part for any direct, indirect, implied, punitive, special, incidental, or consequential damages arising directly or indirectly from any use of the video content is hereby disclaimed. No guarantees or warranties are either implied or expressed that you will have the same results as shown in this video.

Авто/Мото

Опубликовано:

24 фев 2021

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 24

@remmy73 3 года назад

All I need now is a razor pro.. nice video. Good wiring diagrams.

@3DayWeekend 3 года назад

Yes you do! And thanks! 👍

@BengyM 2 года назад

Great video! Did you run your ground wire from the lights to the frame?

@3DayWeekend 2 года назад

Thanks! No, the ground wire can go to the ground connection (black) on the Pulse Bar pigtail.

@K-Risk24 8 месяцев назад

Great video! Did you order the additional wiring extensions as well?

@3DayWeekend 8 месяцев назад

Thanks! No, I didn't have to. They all reached to that mounting location, no problem.

@nathanmcclung658 2 года назад

Is your wiring diagram located anywhere? Nice install!!

@3DayWeekend 2 года назад

Just in the video. I just write up a new one for whatever I'm installing or working on each time. I've seen screenshots of this wiring diagram on Facebook though, so I know it's out there. Thanks for watching!

@MichaelHarris-fg3fk 2 года назад

Which or what kind of relay did you use? Where can I get one? And are the necessary? Why not just run straight power without a relay? Thanks

@3DayWeekend 2 года назад

I used a standard 12v relay from a junk car, but you can find them on Amazon. If you do not connect a backlight to your switch, you can run this directly off the red wire on your bus bar, but the lights will not turn off when you turn off the key. If you have a backlight, you'll need to connect to the yellow wire which is only on when the key is on, but the yellow wire does not have enough power to run accessories. Hence the relay. Hopefully that helps clarify...

@robert100471 2 года назад

hello , how did these hold up ? great video by the way.

@3DayWeekend 2 года назад

I've had them about a year now and they are still going strong. No complaints. Thanks for watching!

@14milehappytimes69 2 года назад

Aren't the rocker switches all. you need to turn them off or on? or what purpose does the relay have?

@3DayWeekend 2 года назад

Rocker switches have a built in backlight LED. If you connect full-time power to the LED, it will drain your battery while the machine is sitting. Instead, you connect the switched 12v from the machine to the backlight so the LED is only on when the key is on. The drawback is that the switched 12v wire cannot support a lot of amperage. That's where the relay comes in. The relay is just a switch. When the keyed 12v is activated, it throws the relay "switch" which sends the always-on 12v (capable of high current) to the device you're powering. No blown fuses, and no battery drain while the key is off. Hope that helps explain it!

@user-wp4nm4kt8y 2 года назад

How may rockers can you run off of one pigtail/relay

@3DayWeekend 2 года назад

Depends on the amp draw. I wouldn't run more than 20 amps on a single pigtail.

@user-qi1zg4bx4v 9 месяцев назад

What would be the best way to wire them if I wanted the lights on a switch but wanted it to where I could still have them on with the machine key all the way off.

@dom_offroad 9 месяцев назад

You’d hook the power wire to the switch you have, then wire the switch to constant power 12v. This way the rock lights will be off unless you flip the switch and they’ll turn on whether the key is on or not.

@3DayWeekend 9 месяцев назад

You can connect to the always-on, but look very closely at your switch wiring. If you connect the backlight pin to an always-on source, your battery will drain down. Most switches have a dedicated pin for the backlight (which you would connect to switched power) and a pin for the load (which you would connect to always-on power).

@khateebyounus9712 3 месяца назад

Hiya mate, what Amp fuse did you use in your circuit?

@3DayWeekend 3 месяца назад

Hi, there! I'm running a 5 amp fuse in this circuit. The manufacturer claims they run about 4.5 watts per pod. 4.5 x 8 is 36 watts total, divided by 12v, and that gives you about 3 amps of draw. Hope that helps! Thanks for watching!