No video :(

Mikuni BS34 Carburetor - Stripdown /Cleanup /Rebuild - Part 1

Подписаться 8 тыс.

Просмотров 5 тыс.

50% 1

Going to do a few videos on my BS34 Mikuni carbs, they are in a bit of a state and some parts are missing they are from my Kawasaki KZ1000J, these carbs are fitted to Yamaha's and Suzuki's as well
Link to my Merchandise shop
teespring.com/...
Follow me on my Facebook page, all welcome to stop by and say hello :-
Hindicobra-669625496577879/
Help me grow and continue by becoming a Patron of The Amateur Bike Builder
Click to join the team.
/ theamateurbikebuilder
You can now follow me on Instagram
/ theamatuerbikebuilder
Alternatively If you just want to say thanks for this video alone,
you can drop a dollar in our "Tip Cup' by using Paypal to hindicobra1969@gmail.com
The money will go to make more videos / buy parts and supplies
If you haven't already, please remember to Subscribe -
/ hindicobra

Опубликовано:

21 авг 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 23

@qivarebil2149 2 года назад

You might want to pop out the needle jet as well. They are tapped out - after removing the main jet and the washer, by slightly knocking at the main jet end, and the jet can be pulled out through the throttle valve bore. It needs to be done, to ensure the small holes on the side of the jets are completely open and clean. I use a hard plastic rod as a drift to knock them loose. If You can find new cheap ones, just replace them, as the seats tend to wear in an oval pattern - causing the air/fuel ratio to be too rich, at all throttle positions. Thanks for sharing this, and good luck on the rebuild! 🤩👍

@qivarebil2149 2 года назад

Just be sure the jets are oriented the correct way around, when reassembling them. There's a tab at the bottom end which fits into a key opening on the jet.

@TheAmateurBikeBuilder 2 года назад

Cheers, appreciate that, i think some are missing, but will recheck next episode, tried tapping the tube but all seized have soaked them and hopefully will come out next time , first time for me on Mikuni complete stripdown so lots to learn , Thanks

@TheAmateurBikeBuilder 2 года назад

Cheers

@bandittunes96 2 года назад

Great episodes, really enjoy watching, keep up the great work 👍

@brianmccall8538 2 года назад

Emulsion tubes to remove, the main jet screws into them. 4 washers and 4 rubber o rings to remove, these will be stuck in the mixture Screw tubes, the ones you took out with the springs on. 4 rubber plugs to remove right beside where the main jets where, that gives access to the pilot jets for removal.

@TheAmateurBikeBuilder 2 года назад

Thanks Brian, appreciate you comment, hopefully they will come out in the next episode as couldn't knock them out,, will look for the other parts as i think there are parts missing, they are in a state, Thanks again

@johnpaulirwin4211 2 года назад

You have forgotten your primary jet and main jet wear The needle slides up and down plus there’s two Spring 2 little ballbearings for your chalk that still left in the cabinet as you will lose them in your ultrasonic cleaner

@TheAmateurBikeBuilder 2 года назад

Thanks John, appreciate your comment, a few of the original jets are missing but will be in the kit when i rebuild them, as for the small ball bearing nothing came out and they were not in the cleaner when i cleaned it out, i have seen them on the fiche picture but not in the carbs

@cu5143 Год назад

Hi bike builder! Great vid ! have a bs34 on my z1 , and wondered if all 3 J’s have the same carbs ?

@TheAmateurBikeBuilder Год назад

As far as i am aware yes they do

@matiasherrera1667 2 года назад

hola, estoy buiscando un kit para los 4 bsd34 de mi yamaha, con diafragma. tienen venta de repuestos??

@TheAmateurBikeBuilder 2 года назад

Try www.nrp-carbs.co.uk/

@geoffreynewton1299 Год назад

How's the old varadero getting on do you still have it?

@TheAmateurBikeBuilder Год назад

Yes, still have it, not touched a bike in 4 months as not been well, so it is in a bit of a state

@marklast2900 2 года назад

Hi what about the pilot jet

@TheAmateurBikeBuilder 2 года назад

Cheers Mark, as i discovered and said in another comment, there are parts missing, but i have the rebuild kits so will be there on re-assembly

@marklast2900 2 года назад

@@TheAmateurBikeBuilder hi amb when u resemble say how many turns out you go on the pilot air screw setting also can you show how you check the float bowl height please

@TheAmateurBikeBuilder 2 года назад

@@marklast2900 will do , Thanks