Millions of washing machines jump on the floor for this, and there are only five reasons a washing machine can jump and run across the floor. Consider the TOP of the washing machine malfunctions, as they say from simple to complex. Do-it-yourself washing machine repair.
☑ Bearings and Oil Seal alii.pub/5zfyqc
☑ Shock absorber 19 cm to 9 kg alii.pub/5zfyv7
☑ Shock absorber 18.5 cm to 9 kg alii.pub/5zfzi5
☑ Shock absorber from 17.4 and 19.4 cm 60-120N alii.pub/5zfztm
💡 My VK group - SUBSCRIBE !!! - diy1000
💡 My site - the link to the video page will be coming soon.
🎥 Bumper repair is cheap and fast - • ⭐ Ремонт бампера БЕСПЛ...
📌 My Yandex Zen - zen.yandex.ru/1000diy
The first reason in the TOP of the washing machine malfunctions, which, it would seem, everyone knows, just in case, we will announce. The clipper should be relatively level on the floor, ideally on a tile, and all four legs should at least rest firmly on the floor.
The second reason in the TOP of the washing machine malfunctions is the most amusing. Applies to new washing machines. In a new washing machine, before the first start-up, remove the shipping bolts that hold the drum.
The third reason in the TOP of the washing machine malfunctions is dry or broken shock absorber gaskets. The shock absorbers are located under the drum. How to remove them? You need to drown the latch and push out the plastic finger. The holes for the pin can contain rubber grommets. If they are broken, you will have to do something sophisticated. The shock absorber rod should go in and out with the force indicated on the shock absorber ± 20 percent. Shock absorbers 100 Newton. For 100 Newtons, the compressive and tensile force must be 10 kilograms. If you have written, for example, 70 Newtons, then the effort is 7 kilograms. Shock absorbers are made of a porous polymer and impregnated with a non-drying lubricant. Damping silicone oil PMS - 60,000 is recommended. But not less than PMS-25000. Oddly enough, millions of washing machines jump on the floor from this and the diagnosis of the washing machine goes in stages.
The fourth reason in the TOP of the washing machine malfunctions can be bearings. Over time, the tightness of the stuffing box is broken. Water enters the bearing. The machine on the spin begins to make noise louder than usual, knocks and backlash on the drum may appear, due to which the machine may run. The oil seal and 2 bearings are cheaper than one shock absorber, but for replacement you will have to remove the tank and remove the drum. Of the nuances, be sure to lubricate the oil seal on the inner and outer diameters during installation. And pay attention to the bushing on which the oil seal will go. It should be smooth. Otherwise, repairing a washing machine with your own hands will go badly.
If the oil seal and bearings are not replaced in time, the drum can wipe the tank and make repairs more difficult. I'll show you how to fix it later at the end of the video. In the meantime, we will continue to diagnose the washing machine.
The fifth reason in the TOP of the washing machine malfunctions is the worst to diagnose - if the shock absorbers are in order and the bearings are not making noise, and the machine has recently started running, then the drum spider most likely has rotted. When replacing the crosspiece of the washing machine, it is recommended to change both the oil seal and the bearings.
When installing the cross, so that the screws do not spontaneously unscrew, a thread lock is applied to the thread.
Became like a dear.
The tank will be repaired as the bumper of the car was repaired earlier. First, we will select the repair material. After selecting the plastic, we can repair the washing machine tank with our own hands. We heat the strips until a wave of molten plastic begins to roll in front. Plastic cools down for a long time - let it cool down. Let's try to tear it off. The material from the canister and the screed were not welded on, and the polypropylene liner worked well. The color will be slightly different, but the tank will not leak. We will clean all the cuts to clean plastic. The occupation is laborious. Finally, melt and fill in all the cuts. Smooth the top with a hot soldering iron. The excess can be removed with a grinder with a petal circle.
We assemble in the reverse order.
The final assembly was carried out after a test wash.
Now you know why millions of washing machines jump on the floor from this. Of course, not everyone will be able to repair the washing machine tank with their own hands, but nevertheless. Everyone can correctly diagnose the washing machine.
This is certainly not a cool homemade product. But, for sure it will be useful to you. You can make repairs to the washing machine with your own hands. Thanks for watching from the author of the channel 1000 DIY's and Advice - 1000 DIY AND TIPS
3 сен 2021
