Mini One, Mini Cooper and Mini Cooper-S, R50 & R53 Door Lock Mechanism & Solenoid Replacement

Подписаться 16 тыс.

Просмотров 11 тыс.

50% 1

Hello everyone, welcome back to the channel!
In this video, I will be demonstrating how I remove and replace the door lock & solenoid assembly on the Mini One and Mini Cooper, this applies to the R50 and R53 models and is very similar on R52 models although the convertible does have a slightly different doors. The basic principle is the same though.
On this particular car, the door would lock from the remote fob but would not unlock. This meant that the door had to be unlocked by pulling on the interior handle every time a passenger needed to enter the vehicle.
Replacement Door Lock Actuator available at the link here - ebay.us/STWjFI
All links to products are affiliate links for which I will receive a small commission on any purchase made, at no additional cost to you.
I hope that you enjoyed this video.
Don't forget to like subscribe and comment for future content from Kev's Shed!
If you wish to offer support to my channel and enable me to continue to bring you quality content then please check out my Patreon page at the following link - www.patreon.co... - Thank you.
Join me on the socials at the following links
Kev's Shed on Facebook - / 561477094498994
Kev's Shed on Instagram - / kevins_shed
Kev's Shed on Twitter - / catakev79

Авто/Мото

Опубликовано:

12 сен 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 19

@Bikebloke0 2 года назад

Not only are you helping with my VFR800 I’m also doing this same job today 😂

@ohLunaah 2 года назад

Thanks so much man I was getting very very frustrated lmao. Very helpful👍🏽

@TiggerzSRi Год назад

This video really helped! Thanks mate! Although why I’m doing this in early January is beyond me and you have a warm summers day 😂😂

@flippingcarsrepairs 4 дня назад

Just had to do this same issue😮

@frankiebye 10 месяцев назад

Excellent video, many thanks for taking the time to film and share. Could you tell me if your existing key was immediately successful or did you have to somehow sync them?

@KevsShed 10 месяцев назад

It doesn’t affect the lock at all mate as that is independent of the actual mechanism so nothing to worry about with the key 👍🏻

@frankiebye 10 месяцев назад

@@KevsShed Thank you for your time Kev. The part I bought is second hand but complete. Lock, solenoid, cable etc. It's a convertible and there isn't a key entry on the n/s meaning it operates from drivers side. Sorry I wasn't clear. I wondered if the original fob had to be programmed the new Lock. Sorry as you've probably gathered I'm no mechanic 😁, cheers 👍

@gavinrodgers3886 Год назад

You do not have to remove the window mechanism , only take the bottom 10mm bolt out , mark it original position with a marker pen and pull to the inside skin of the door Thanks for reading ........just to save time , Cheers then mate ps I've jus replaced this part Myself .

@chrispayne1029 2 года назад

Great job 👏👌👍

@AdeReeves 3 года назад

Evening Sir ... 😃

@KevsShed 3 года назад

👌😎

@stevefiler1631 5 месяцев назад

Hi, Thanks for the info Kev. Now then, my mini {2011, R57 LCI} has a slightly different problem. Both my fobs appear to unlock my car, but, neither handle will open the door. My inner door panels appear to be different than yours. I think that I need to have the door open, to remove the inner panel. How can I overcome the door latch? Any thoughts? Steve.

@vinnie39 2 года назад

Any tips on re attaching the fiddly outter handle cable?

@deleted_why Год назад

Intermittently, my wife's 2013 door will not latch fully shut... when you let go, it remains slightly open. Is the Actuator the problem?

@cdavey061 Год назад

You did not need to remove the window strut just remove 10mm bolt under door mark inside on the plastic slider its position then move it back to enable actuator to come through its a tight fit but at the right angle it comes out...