Mitsubishi Triton, P2413, Fixing EGR problems and build up of carbon in induction systems.

Подписаться 8 тыс.

Просмотров 680 тыс.

50% 1

Mitsubishi Triton 2008
Codes P2413 EGR Valve Fault.
We Will Now NOT do this job without removing all of the inlet manifolds . There is NO Chemicals out there that will remove this Carbon Build up... I Don't care what you use it will NOT remove that shit out of there. Manifold MUST be removed for manual cleaning. Then you can use Chemicals to remove Carbon and other matter from the engine cylinder head, Valves and pistons and Exhaust.
that is the only way , And it is LABOUR intensive .
We have invested in a lot of Cleaning machines to do the job correctly, High pressure hot wash and Hot sonic bath's.
Contact Information
WEBSITE
www.ptauto.com...
FACEBOOK
/ ptprecisionautomotive
BUSSINESS CONTACT
02 9907 6662
1/2 Paton place, Balgowlah NSW, 2093
fault
ute
car
truck
speed
power
loss
slow
scv
suction control valve
fix
diagnose
mechanic
motor
race
fast
fuel
diesel
mitsubishi triton
mitsubishi triton
4WD
toyoyta hilux
hyundai
surging diesel
lack of power
diesel common rail
high pressure common rail
1800rpm to 3000rpm
idle iratic
diesel problems
nissan diesel
ford diesel
Volkswagen, BMW, Fiat, Hyundai, Hyundai iload, Hyundai H1, Mazda, Mazda BT50, Diesel Injectors, Diesel Piezo injector, Common Rail Diesel injectors, Common Rail, Mitsubishi , Mitsubishi Triton, DeCarbon, DeCarbon Induction system, On Car DeCarbon, Induction clean, Diesel induction clean,
Missfire , Lack of power, No power, Running rough, Hesitation, High pressure pump, No pressure, common faults, Diesel injection test bench.Toyota, Toyota Prado, Toyota Hiace, Toyota SR5, Toyota HiLux, , 2.0litre, 3.0litre, 3.2litre, 2.5litre, 2.8litre,
Volkswagen T5, Volkswagen transporter, Volkswagen caddy.

Опубликовано:

25 сен 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 111

@policeasian7848 8 лет назад

Very good mechanic and honest unlike some that have no idea and over charges you to the max keep up the great work my friend

@onajurecjhay1 7 лет назад

I had mine blanked..older isuzu dmax and 2017 dmax both blanked..no problems so far

@davidjames666 8 лет назад

Todays cars suffer from a dirty intake, but have a clean exhaust system. The opposite from a few years ago. Either way, the residue blow by is getting trapped, but for the intake, is causes performance issues.

@jmdrawks 7 лет назад

My 3.0 D4d @ 160,000kms Throttle body, Inlet manifold was 30% blocked. I end up doing a manual scrap & clean of soot which managed to fill a full can (375ml). Exhaust Gases and Oil vapour is the worst thing you can mixed as it become very gluey soot. Oil catch can is now fitted.

@hbmair351 6 лет назад

Egr is closed all nice and clean, disconnected it after cleaning intake and everything ells. Will put vacuum line back today and see. Here in South Africa we dont have emission problem and inspections. I replace the complete turbo and install 4 new injectors. Will have them programmed in the ECU today. Will keep you updated interesting

@PTPrecisionAutomotive 6 лет назад

yeah the best way to delete an EGR valve is to just block it off (where the gas re-enters the intake system) or at the exhaust manifold rather then just unplugging it. let me know how it goes after you do the ECU and try it plugged back up.

@MINAJ24 9 лет назад

Your good you! I just got new EGR fitted, bet they have not done all that cleaning. Seams a waste to fit new one with all that stuff full of gunk still

@langerz5686 5 лет назад

same mate, how did you go?

@niceboy60 9 лет назад

this issues can be Minimized with premium Diesels which improves combustion and clean the Injectors hence reducing exhaust deposits

@standupstraight9691 3 года назад

Think about how the egr system works. Then restate your advice.

@vivauruguay 9 лет назад

I wish I had seen your video before and gone to you for help as there seem to be a lot of cowboys out there that not only will give a brand a bad name but also do not have a clue on what to do when it comes to built ups on the EGR system.

@SpencerHHO 9 лет назад

Apparently brand new cars with high levels of valve timing variability don't have EGR anymore as the valve timing and better mixture controls do a better job at reducing NOX anyway.

@rossco289 6 лет назад

Hey mate, appreciate your honesty, great to see, I'm an old Diesel fitter ex railways, one thing we were taught was servicing, filters oils etc etc. Great video, will watch out for your other videos.

@CGV.69 5 лет назад

I clean my own and fitted a 7mm blanking plate. Great vid

@jamesdickson3616 6 лет назад

How much dose all this cost

@scottiebones 7 лет назад

EGR and DPF are an absolute pain in the arse, worst emission control features ever designed.

@langerz5686 5 лет назад

agreed

@kuromurasakizero9515 4 года назад

nah, catalytic converters are worse. mining the materials to make them, expense, destroying engines when go bad, robbing engines of power, heavy, etc.

@mikewatt1376 4 года назад

150000 ks of emissions just got pumped into the atmosphere in 15 mins

@bigbore400 9 лет назад

You can see there's no oil catch can on the engine. the crankcase ventilation hose is sending all the oily/fuel "blow-by" vapour from the top of the engine...back into the big air intake pipe just after the air filter. 6.33min Good video thanks The EGR valve can get blocked but it actually does a positive thing by shrinking your engine and saving fuel at low engine speeds. At wide open throttle the EGR valve doesn't doesn't have any effect. The EGR valve only opens at small throttle openings. Would it do any damage to put a blanking plate on the EGR on a turbo diesel... by causing excess heat? Just for the purpose of not having blocked EGR issues due to carbon.

@wilhelmhesse1348 5 лет назад

It had to be a Mitsubishi damn these cars, very powerful machines but once they start giving problems it's onething after another

@petercambulaso3858 5 лет назад

Can my codes on an Audi A5 2013 tdi still have codes of 1) EGR valve open circuit 2) Exhaust gas Recirculation Sensor A circuit/range performance 3) EGR valve open circuit If it was just totally blocked up ?

@vlfreak 9 лет назад

looks like and interesting and effective process. my only question is, do you REALLY think maintenance is the issue, especially in a 60k old car? if you believe it should be done around 40k, i reckon design is more the problem, not (lack of) maintenance. 10yrs ago this is the kind of treatment you would expect to give a 400k old diesel for a new lease of life not a 3yr old one :/

@kazza3281 7 лет назад

Emission control systems have historically been a massive issue with all engines. Due to fuel/diesel not being a clean product to run cars on. Simply rerunning the exhaust gases to try and give them a second burn off is just ludicrous. I, personally, think that more energy needs to be put into electric cars and cars that run on hydrocarbons. The problem there is big corporations can't make a ton of money out of it. I'm sure that when the day comes, and it will, corporations will find a way to screw us over anyway. Good maintenance practices and how you drive has the biggest impact on your engine.

@nickbordo 7 лет назад

I have a question Phil: If the customer of this Triton had of used a synthetic diesel engine oil such as Mobil Delvac 1 15W-40, do you think that the vehicle's carbon deposit problems would have been less or non existant? I'm curious of your professional opinion of this issue. I personally use Mobil 1 5W-30 in both of our Toyota's (RAV4 and Corolla), and have done so since their first oil changes from new. I've put my dad onto using Mobil Delvac 1 15W-40 in his Isuzu D-Max. His vehicle seems to be running great.

@PTPrecisionAutomotive 7 лет назад

oil isn't the the main issue with carbon build up its caused mainly by the use of the EGR system and city driving mixed with engine blow by. If the owner of this vehicle drove the car twice a month at 100km/ph for an hour or more then the likelihood of it having carbon built up would be minimized. If you were also to add a oil catch can rather than having the blow by go into the intake system then I doubt you would have any problems at all.

@philthorsen4336 10 лет назад

We Are at 1/2 Paton Place Balgowlah NSW near Manly

@LiamAndGames 7 лет назад

DO you ever have problems with the Mas airflow sensor throwing codes when doing an engine decarb or large bits of carbon coming off and into the cylinders?

@PTPrecisionAutomotive 7 лет назад

no usually it won't throw the light on unless we have something disconnected.

@rommeltolentino2518 8 лет назад

How to fix the Lexus ES 300. check engine light on. but I change the sub 1 oxygen sensor and sub 2 oxygen sensor.and I used the snap on scanner to delete the but still on check engine light. do you another idea to fix it this car THANK you.

@martinquintana5005 7 лет назад

does anyone know. what is wrong when your egr pressure sensor is melted and loat of power

@MrDigger450 5 лет назад

Great info want your opinion of blocking them as that’s what people say to do cheers 🍻

@PTPrecisionAutomotive 5 лет назад

sure . but i can not say that .

@Footrotflats251 7 лет назад

how many km did it have? - our pajero with a 4M41 motor is at 192'000km and hasent had any issues yet

@BrucePinkerton 21 день назад

How dies all the loosened carbon get through the dpf?

@PTPrecisionAutomotive 21 день назад

it can't you need to remove all manifold to clean out first

@JoseGomez-xc1vb 9 лет назад

hi phil my dad has the same truck and keeps coming up with mil code p1276 and i was woandering if you can help with the right definition for this same model thanks

@2jzdemon 6 лет назад

Its getting to a point where its not worth owning a diesel anymore so much bullshit on them! 😩

@PTPrecisionAutomotive 9 лет назад

You could just block the EGR valve off But that is not legal. The EGR is there to do a job . there are underlying issues that can cause carbon and sludge to build up, eg to much crank case pressure , leaking injectors and seals,, lack of oil changes, low grade oil's etc.

@محمدسالم-ي7ر6ذ 2 года назад

I have a problem, I replaced a full machine, still the same problem, spraying it in the water depot

@PTPrecisionAutomotive 2 года назад

Not sure what you asking ???

@gregkingston2087 7 лет назад

Ive just cleaned out my inlet manifold with acid bath which was pretty blocked up with gunk. Also the EGR valve. Can you tell me if blanking the EGR will give the engine more power and economy? Ive been told it will cost $700 to remap my toyota Hiace 2009. What is your opinion re the extra power and economy? Could I blank it and drill a 8mm hole in the centre of the blank to minimise build up. Would this still give more power etc? Or should I just put a catch can in for $300? The catylictic converter has been bypassed..cheers

@jaggass 8 лет назад

This wouldnt happen if engines didn't have EGR valves.

@wazza33racer 9 лет назад

EGR is a crock. High performance cellulose filter that removes dissolved water (Jet/Diesel/Petrol all have it) knocks out NOx and greatly reduces soot. Manufacturers need to get their heads out their behinds and investigate alternate methods to deal with NOx. Plus fuel economy improves 3 to 5%. Aussie truckies and mining industry have been using them for years.

@Abfs900 2 месяца назад

hey guys, to do a full clean like is what is in this video. what would the cost be at the end or a ball park. i have a triton 2014 MN

@PTPrecisionAutomotive 2 месяца назад

Please call the office to discuss . Thanks Phil 02 99076662

@quanglam4580 9 лет назад

can you do a post on how do a egr clean on a 2010plus Toyota turbo diesel prado this would help out everyone that that cant get to a mechanic and live in the country..it would help out heaps

@lollysquish2373 5 лет назад

My car cuts out when I slow down or stop (not everytime), nothing is coming up on the reader so no one has yet worked on it. How would i know if it was the egr, acv or something else? Thanks

@PTPrecisionAutomotive 5 лет назад

your going to need a mechanic who knows what there doing to work that one out.

@lollysquish2373 5 лет назад

@@PTPrecisionAutomotive thanks, I dont think any do. They just use the reader and nothing comes up so they have no idea. I can smell petrol at times when shes warmed up. Just gunna take the car to the garage and pay for them to look at the car rather than them just use an obd reader. Thanks

@antonyroberts803 2 года назад

How much money to do all that I Wonder.

@pranksterle 9 лет назад

its a pitty your not in perth would love to have this done by someone who knows what they're doing like you guys

@literbikedoc 6 лет назад

There are some good shops in WA - like anywhere few and far between!

@peterbilt6665 6 лет назад

Go to the Ronny Dahl RU-vid channel have a look through it and go to the people he uses in Perth sorry I can't remember at the moment cheers good luck

@oozuk 4 года назад

I would be interested to know if you have put a bore scope in the inlet tract and runners of some vehicles treated to see before and after results of this process, curious if this process is yelding the same results as ultrasonic off car manifold cleaning and media blasting of the inlet. Would love to know your thoughts

@PTPrecisionAutomotive 4 года назад

the only way to do a complete clean is to remove all manifolds, NO product will ever clean it off with out manual clean first. BUT it cost [labour] some people don't want to spend [invest] in doing it that way. but these day's i only want to remove all manifolds..... and do it correctly. [it's the best way]

@oozuk 4 года назад

@@PTPrecisionAutomotive thanks for the reply. as a fellow mechanic I was interested on your feedback on this process as I have only cleaned them via removal in the past.

@bigon42 7 лет назад

Garage In the Caribbean we seeing lots of diesel egr problems, we remove and clean by hand, where can we get the equipment that you use (Not the Liquid) to buy

@PTPrecisionAutomotive 7 лет назад

www.bgprod.com check their site out.

@rtcivic 7 лет назад

does the check engine lights up with this problem? i have a bk pajero 2008 mdl i think its the same engine on this video.

@alexlawrie7840 7 лет назад

@danielredmond4156 7 лет назад

hay mate im from vic i have a mn triton was wondering the cost on one of these cleans? and any suggestions on who to contact in vic. cars done just over 200000 so well overdue, tia

@Altruistic00 4 года назад

Will these mess up with the DPF?

@Krooker85 6 лет назад

Quite a common problem in the 2.5ltr tritons

@butchauchtung9831 6 лет назад

I have a 2005 Lincoln is my car sounds like it has a miss fire and it is blowing the oil all over the engine. When they scanned the car it showed the EGR valve and also the oxygen senceir. Can any one help me please

@PTPrecisionAutomotive 6 лет назад

Lincoln what? what fuel type? what engine? What are the actual codes? does it have excessive blowby? (remove and sit on hole does it fly off)

@irishoz7914 7 лет назад

do you know anybody in victoria offering this service

@hbmair351 6 лет назад

Hi I removed my vacuum pipe of my egr and blocked the vacuum tube off. Can the disconnected egr cause low performance on low rpms. Got a e46 320d turbo only kicks power at 2800 revs. Please let me know if you would be so kind

@PTPrecisionAutomotive 6 лет назад

is the EGR valve closed? have you tried plugging the hose back on and seeing if the power comes back? usually when they fail you have no power at low RPMs because they get stuck open.

@scottturner7679 9 лет назад

Hay Phil I cleaned all that carbin out of the intake now tritan won't start fired once 2007 3.5 turbo GXL any thoughts

@michaelallen6208 4 года назад

Hi did you end up working out why it wouldn't start

@ur2slob724 7 лет назад

Just block the egr $20 plate no more egr problems

@luouns 2 года назад

That looks like a djw right there

@stephenhall6332 7 лет назад

Very informative.

@martinheuts 9 лет назад

2:36 Looks like a plastic bottle of Jupiler beer LOL

@waynenicholson1172 6 лет назад

Great video. Where are you located, I need to the same clean for my Mitsubishi Pajero?

@PTPrecisionAutomotive 5 лет назад

In Balgowlah NSW

@benspilsted2286 6 лет назад

What do you guys charge for this ?

@PTPrecisionAutomotive 6 лет назад

give us a call and we'll run you through it all as price varies (02) 9907 6662

@anthony-me1wu 4 года назад

does a catch can eliminate these problems?

@PTPrecisionAutomotive 4 года назад

yes will help

@anthony-me1wu 4 года назад

@@PTPrecisionAutomotive Thanks mate, wish you were closer to the Gold Coast you'd have my business. Thanks for your expertise

@PTPrecisionAutomotive 4 года назад

All good mate

@dalegoodman6421 6 лет назад

Yeah,....that's what I gotta do

@william0803 10 лет назад

Where are you guys located??

@haydnsmith6974 6 лет назад

How much does it cost to get this done?

@PTPrecisionAutomotive 6 лет назад

give us a call on (02) 9907 6662 and we'll run you through it mate

@mattbundy1 10 лет назад

G'day Phil, what's the cost of that treatment on a ML Triton?

@philthorsen4336 10 лет назад

Hi there it can cost up $700

@dz-hc3zj 6 лет назад

Phil Thorsen....where are you based now mate.

@hbmair351 6 лет назад

Will do thank you

@PTPrecisionAutomotive 6 лет назад

hey mate just curious how did you go with your car? were you able to getting running good?

@peterrussell2341 4 года назад

nice bloke

@vairavippillaisivagnanavel6813 9 лет назад

I live in London Where can I contact someone , to get my VW golf plus EGR valve regularly serviced to prevent it clogging up. Just now my EGR valave is being replaced (after 39,000 miles !!!. I wish to have a tel no and email address.

@breffni28 9 лет назад

@trishbrewer743 7 лет назад

i wished you were closer to me. very informative videos. good to see a mechanic that knows what hes talking about.

@standupstraight9691 3 года назад

....and delete the egr while you're at it.

@bignoel32 7 лет назад

what a joke diesel engines are these days, time for us all to go back to the ass and cart.

@TheBlabla1996 7 лет назад

True better of buying an older diesel with direct injection and no egr shit

@Outbackbogan 6 лет назад

Basically prob didn’t maintain his triton that good

@jamesdickson3616 6 лет назад

I’ll keep my old diesel even get it rebuilt rather than put up with all this expense

@PTPrecisionAutomotive 6 лет назад

mate as long as you're looking after it you shouldn't have to deal with these problems. A lot of them are caused by city driving and lack of maintenance

@Footrotflats251 7 лет назад

fuck 60'000 - somthing majour is wrong . - our car has 192'000 and hasent had any light come on!

@PTPrecisionAutomotive 7 лет назад

city driving mate just kills these EGR systems

@Footrotflats251 7 лет назад

bloody hell - im glad 99% of our driving is at 100kmh