Тёмный

(MKII) 1985 Toyota Celica Supra -- Re-Seal your old Power Steering Pump 

John's neverending list of random things to do
Подписаться 2,3 тыс.
Просмотров 2,6 тыс.
50% 1

This video will give you a general idea on how to reseal your old leaking power steering pump.
Retainer Clip Tool:
www.homedepot....
Sealing kit:
www.autozone.c...

Опубликовано:

 

21 окт 2024

Поделиться:

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист
Посмотреть позже
Комментарии : 18   
@enterBJ40
@enterBJ40 9 месяцев назад
Your video helped me to assemble my pump in my 1984 Cressida. Thanks a lot !
@OwenXW
@OwenXW 3 года назад
please keep up the celica supra videos, as a young enthusiast it is so very helpful to be able to watch these videos, keep up the amazing work!
@LexBee
@LexBee Год назад
Thank you so much for the break down. 🙏 really made the job go smooth.
@rxblx2442
@rxblx2442 3 года назад
Great info and steps! This is one of your best!
@autostationfanatic
@autostationfanatic 2 года назад
I have a 87 toyota pickup 4x4 22re, my power steering pump has a leak. Are they the same? As the one you rebuilt?
@lewisparfoot8704
@lewisparfoot8704 2 года назад
Also same question but for a 1986 pickup haha
@jonathangarcia4439
@jonathangarcia4439 3 года назад
Cool ! ✌✌
@XDarkSTUNTX
@XDarkSTUNTX 3 года назад
Please make a video how to change the antenna
@johnsneverendinglistofrand1377
@johnsneverendinglistofrand1377 3 года назад
Still looking for a good replacement. Since my radio doesn't have a dedicated radio antenna turn on I can't use the motorized antenna otherwise the antenna will be up whenever the radio is turned on. Alternate solution is to put in a manual switch but I'd probably forget to flip the switch.
@abdulazizalzhrani1662
@abdulazizalzhrani1662 2 года назад
Thanks John for the great videos, i have tried to fix my pump, but after installing it back again on the car i notice that it doesn’t pump any fluid and there’s no whine sound, what could be the cause?
@johnsneverendinglistofrand1377
@johnsneverendinglistofrand1377 2 года назад
Did you put everything back in the same order? How did it look inside?
@abdulazizalzhrani1662
@abdulazizalzhrani1662 2 года назад
@@johnsneverendinglistofrand1377 yes i followed every step as described, and from the inside it looked good, there weren’t any scoring, do you think that maybe one of the shims fell off from the rotor, although it was all fitted perfectly with round edges on the outside
@johnsneverendinglistofrand1377
@johnsneverendinglistofrand1377 2 года назад
@@abdulazizalzhrani1662 you made sure to clean the filter media in the reservoir? And placed the woodruff key where the pulley mounts to the pump?
@abdulazizalzhrani1662
@abdulazizalzhrani1662 2 года назад
@@johnsneverendinglistofrand1377 i cleaned the filter using brake cleaner from underneath, as for the key i put it in its spot, but i’ll recheck if it fell off while mounting the pulley
@johnsneverendinglistofrand1377
@johnsneverendinglistofrand1377 2 года назад
@@abdulazizalzhrani1662 check those 2 vacuum lines too.
@Bbbb-cl5re
@Bbbb-cl5re 3 года назад
Hey John can you please make a video on how to change the ignition cylinder ring light to make it more brighter?
@johnsneverendinglistofrand1377
@johnsneverendinglistofrand1377 3 года назад
Is that where the key fits? Don't think mine is there. LOL. Fixing up a video on turn signal mods. I'll look up what your asking though.
@Bbbb-cl5re
@Bbbb-cl5re 3 года назад
@@johnsneverendinglistofrand1377 yeah there should be a circle green light around the keyhole . Keep up the great vids though!
Далее
(MKII) 1985 Toyota Celica Supra Hard Cold Start
13:59
Landcruiser Power steering pump rebuild
21:09
Просмотров 2,6 тыс.
(MKII) 1985 Toyota Celica Supra Turn Signal MODS
11:53
Просмотров 2,3 тыс.
How to remove and install a Power Steering Pump Pulley
10:02