MPFI WIRING ! EF CIVIC WAGON B20 SWAP PT 3. HSG EP. 5-31 

hey another great video like how you added charts and diagrams makes researching a lot easier. hands down one of my 2 favorite channels on you tube. keep it up man.

great video guys. very informative.

I am only 15 and I did a mpfi swap

love the vids wish there was accord vids like theses

yo the best dpfi to mpfi tutorial ive seen great job mane!!!!!

Nice video i wish someone can do that job on my wagon

6 years later its better to get the ebay obd1 tuck harnesses that go for $50-70 the one i got did have the wires pinned correctly 3.30.24 but you do need to buy the rywire chassis adapter harness to make that work so for $200 you get to use a fresh harness versus this method in the vid was nice from early 2000s til then 6 years ago but for the most part these 30-35 year old harness no matter how nice and preserved the car is these harnesses are brital any movement the copper sleeves crack exposing or coming apart specially that oil pressure switch wire

✊🏽✊🏽👍🏽 HSG

Can you please make a video showing how you change a 7 wire o2 sensor to a 5 wire. I'm trying to swap a b18b1 into my 1996 hx, but there is not any good information on how to make the change from 7 wire to 5.

i recently cut my injector power block out and soldered the one yellow/black wire to the 4 injector wires just to get rid of that block that was just hanging there and i thought was pointless. the car runs but was that a bad idea?

On the resistor box what pin # does that wire run to

The power block I have for the injector has more than 4 black and yellow wires, which wires do I connect to the 4 black and yellow wires for the injectors?

What would happen if the a15 wasn't hooked up? Would it run? This is killing me bought one already done it's running but like crap. The iacv or fitv is sucking air like crazy? No check engine light. Driving me nuts lol

Will the injector wires work the same on a 0bd1 ecu

Do you leave the E.c.u. for the d series in it while still running the b series one as well?

the PR4 would've ran this without a jumper harness right?

hi i have lxi civic 2000 i want to swap b20b can you givr me advice how can i connect the wirings

pro

And where did you get the plug for the injection.

I have a 97 CX Hatchback b18b1 swapped and cannot find the downstream sensor. Can you please help

How can I wire an Ef original obd0 distributor pigtail to fit on the Obd1 block that goes to the obd1 distributor? I have en ef that the person converted too make fit but is taken apart now when I got it. Just need a diagram or info on here if y’all would thanks!

What about map sensor

Monotech ayyeee i bought a few of his stuff too

I have an ef hatch that was dpfi and i converted it to mpfi and dropped a b20 in it im using obd1 with an obd1 LS ecu and it starts and runs but when i go to drive it, it gets to 3000rpm and starts kicking itself back down like its hitting the rev limiter I dont have a knock sensor hooked up and when i go to check the mil light the light turns off and doesnt give me the code im at a loss what could be posibility of my car doing this

Mark, Why are you selling your integra? its clean, fast and you built it very well. I don't see why you'd wanna get rid of it so soon.

nice video but I will go to junk yard grab 0bd0 civic si dash n engine harness all together

yoh do you have any B series OBD2b for GSR? Distributor? you selling? im buying one if you have any

Hey you should actually make a full guide showing and explaining more into depth I get that your busy with the b20 swap but I think it would be cool if you recorded everything and more in depth I liked this one cleared a lot of my question for my friends Crx which is not multi port but dual port and has a d16y8 we got stuck with what harness to use stock one and modify it or buy and multi port one and work with that ?? But thanks awesome video !

If I’m running a 2000 b18b1 which is OBD2 what connector harness would I get?

Where did the other videos for this build go?

I rather buy a rywire harness for the set up lol

any plans on doing a how to turbo your car vid

take a lil more time and try to make your solder connections look better... other than that great video

Honda Advertisement Garage

Hey guys check out Jon widmer channel for more information trust me it's much more explained

I need someone to swap my.90.ef wagon to b20

yo hey how would i go from obd2 to obd1 plan on taking my d16y7 for a sohc zc

IT really bothers me to see you use tape instead of heat shrink tubing for a cleaner and tighter bundle of wires. I try and use U-clips to crimp around the wires almost like a butt connector but not bulky. Crimp, solder, heat shrink. But I can get it since usually you on time and $ budget. Like you said, its not a show car.

Sloppy wiring

Dude why don't you just show the process? That diagram is mad confusing. Do my research? Then why am I watching this? Danm bro..