Тёмный
No video :(

Mustang Transmission Removal / Install (99-04 V6) (4R70W) 

OldSchoolNoe
Подписаться 6 тыс.
Просмотров 4,3 тыс.
50% 1

How to remove the automatic transmission on a 99-04 V6 Mustang. Video starts with the catalytic converter y-pipe, driveshaft, and starter removed. Video shows important removal information and install tips along with torque specifications. How to remove the top 2 transmission bolts. How to disconnect the torque converter from the flexplate.

Опубликовано:

 

5 мар 2024

Поделиться:

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист
Посмотреть позже
Комментарии : 16   
@arbitrarynumberz
@arbitrarynumberz 4 месяца назад
Thanks for the upload, my New Edge's rear main seal is going out and this video will come in handy soon enough.
@plsdonate4486
@plsdonate4486 Месяц назад
Pro tip. For the top 2 bolts just remove your intake manifold. Cheaper and less stress and saves you a trip to the store
@OldSchoolNoe
@OldSchoolNoe Месяц назад
never done it that way, would be a good opportunity to change some of them gaskets.
@thelonelytuba1972
@thelonelytuba1972 5 дней назад
The wiring harness gets in the way while doing that, any tips on getting the wiring harness out of the way.... beating my head against the wall on this job
@ThugzBunnyYT
@ThugzBunnyYT 2 месяца назад
Could I get away with not doing the torque converter bolts and just pulling the transmission off?
@OldSchoolNoe
@OldSchoolNoe 2 месяца назад
Nope, I've tried this before. What happens is there is not enough clearance for the bellhousing to clear the left behind torque converter when pulling the transmission. It hits the bottom of the car. That torque converter is going to have to be unbolted.
@ThugzBunnyYT
@ThugzBunnyYT 2 месяца назад
@@OldSchoolNoe I actually managed to get it off without doing so funny enough
@OldSchoolNoe
@OldSchoolNoe 2 месяца назад
@@ThugzBunnyYT what the...must have had the perfect downward angle to clear it out, nice!
@ThugzBunnyYT
@ThugzBunnyYT 2 месяца назад
@@OldSchoolNoe exactly what we did slid it back and droooped it and it’s slid down and off onto my tranny jack was a bit of a pain but it came off
@joekienzle4409
@joekienzle4409 4 месяца назад
Where did you get the converter holding tool
@OldSchoolNoe
@OldSchoolNoe 4 месяца назад
Ebay
@MaverickMitton
@MaverickMitton День назад
Is this a manual or automatic? Does it make a difference?
@OldSchoolNoe
@OldSchoolNoe День назад
this is an automatic, a manual is much easier because you unbolt the transmission from the bell housing, and can remove it separately.
@codenamecompton8689
@codenamecompton8689 Месяц назад
When I popped my transmission out, a small compression spring came out.. Any ideas. Same car v6 mustang
@OldSchoolNoe
@OldSchoolNoe Месяц назад
That's interesting. There is no spring near the bellhousing area. I have not rebuild this type of transmission, so not sure if its an internal piece.
@normastanley4977
@normastanley4977 3 месяца назад
promo sm
Далее
Cómo armar una transmisión AODE/4R70W FORD
19:57
Просмотров 45 тыс.
99'-04' Mustang Common Problems :)
6:12
Просмотров 384 тыс.
БАТЯ В ДЕПРЕССИИ
00:52
Просмотров 737 тыс.
Mustang GT 4.6 engine and transmission removal.
31:32
TRANSMICION 4R70W FORD MUSTANG 99-04
21:37
Просмотров 1,8 тыс.
WATCH THIS BEFORE REPLACING YOUR TRANSMISSION!!
9:13
Просмотров 762 тыс.
Fixing oil pan leak, rear main seal & motor mounts.
23:33
How To Replace The Clutch On a 99-04 Ford Mustang
13:01