Тёмный

nanoVNA - Alligator Clip Leads vs. VNA Test Fixture Kit - Measuring Inductors & Capacitors 

Gregg Messenger - VE6WO
Подписаться 2,6 тыс.
Просмотров 9 тыс.
50% 1

Does using a more formal test fixture with the nanoVNA result in better measurements when testing inductors and capacitors to confirm their nominal values?
Test Board Kit - a.aliexpress.com/_mr2a0U6
0:00 Introduction
3:58 Full calibration of the nanoVNA
6:13 Hooking up the test fixture
6:37 Measuring the inductor value
8:40 Why measure at + and - 90 degrees on the smith chart?
10:40 Measuring the capacitor value
12:38 Testing the measurement accuracy
14:32 Building the parallel resonant circuit
15:10 Setting up the nanoVNA to measure the resonant frequency
16:29 Measuring the resonant frequency
18:34 Examining the results
20:29 Hooking up the alligator test leads and calibrating the nanoVNA
22:39 Measuring the inductor value using alligator leads
23:49 Measuring the capacitor value using alligator leads
24:56 Comparison of results and conclusion
VE6WGM (VE6WO)

Наука

Опубликовано:

 

6 июн 2024

Поделиться:

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист
Посмотреть позже
Комментарии : 30   
@acestudioscouk-Ace-G0ACE
@acestudioscouk-Ace-G0ACE 2 года назад
As a beginner in electronics, I found this fascinating and was able to to follow due to your clear and relaxed presentation style. Thank-you.
@ve6wo
@ve6wo Год назад
Glad it was helpful!
@rfburns3472
@rfburns3472 4 месяца назад
Very nice demo. I was about to do the same test. One thing I noticed, and it may be minor, is that you held onto the back allegator lead which may have induced some hand capacity in the measurement. Even though it was the black shielded allegator clip it still could have some effect.
@intotheblue50
@intotheblue50 6 месяцев назад
A lovely clear presentation style, showing your comparison project which is informative and very enjoyable, thank you.
@enriquea.wembagher5537
@enriquea.wembagher5537 2 года назад
Gregg ...Excellent work and demostration !!!! Vy 73
@keyboarderror1
@keyboarderror1 Год назад
I soldered a couple of SMA connectors to Dupont pin headers for an easy way to use them with a breadboard. It works pretty well, and you can use the split sides of the board for through connections. If you don't have a dedicated test fixture handy.
@ve6wo
@ve6wo Год назад
Thank you
@ka2pbo
@ka2pbo 8 месяцев назад
That was fantastic! Great explanation the whole way. I agree; for ham radio and electronics experiment stuff, the clip leads are just fine. I have a test fixture but always go to the clip leads .As long as you calibrate each and every time, you're good to go. 73 and Thanks
@TheSmokinApe
@TheSmokinApe 2 года назад
Well done, I really enjoyed this video 👍
@ve6wo
@ve6wo Год назад
Thank you :-)
@Sethz71
@Sethz71 2 года назад
Big fan, keep it up Gregg!
@jwrtiger
@jwrtiger 10 месяцев назад
Nice video, thanks!
@FUNKLABOR_DL1LEP
@FUNKLABOR_DL1LEP 2 месяца назад
4:41 Hi, great job! I saw You turning the SMA connector into the SMA nut, You should always turn the nut and not the adapter. if You turning the Adapter, it is rotating in the connector, this will damage it over Time. 73 de DL1LEP
@ve6wo
@ve6wo 2 месяца назад
You are correct. Since this video was made I have started to support the coax with one hand to allow the nut to rotate while preventing the center pin from rotating.
@DmitryAvsioukov
@DmitryAvsioukov Год назад
When solving back for L you've actually solved it from calculated frequency, not measured one. No surprise you've got your 14.8uH back :)
@ve6wo
@ve6wo Год назад
Yes, I’m not entirely happy with that part of my video. Looking back at it, I think I could have presented what I was trying to say more clearly.
@JimSky
@JimSky 2 месяца назад
Seems like the test fixture should be used in the calibration of the VNA.
@geokuf9679
@geokuf9679 2 года назад
Excellent, thank you, 73
@BobMellor1954
@BobMellor1954 Год назад
Thanks for this, very interesting, just subscribed 73 Bob
@ve6wo
@ve6wo Год назад
Thanks for the sub!
@MichaelPechner
@MichaelPechner 5 месяцев назад
frm what I can tell the only pins connected to out si column 7 rowsc,d,e. B ut you connected the inductor to row A. i assume you modified your board?
@JPEE2012
@JPEE2012 Год назад
I would have thought that the calibration for the alligator clip would be more accurate, because you calibrated it to the tip of those. With the test board, you did not calibrate it inline with calibration procedure- it was left out. That board could affect the capacitance and inductance, right?
@ve6wo
@ve6wo Год назад
Yes, however, at the wavelengths we are using to make these measurements this small change in length means very little to the resulting measurement. At higher frequencies, this becomes much more critical.
@renaat9829
@renaat9829 4 дня назад
👍👍👍👍😊😊😊😊
@galileo_rs
@galileo_rs Год назад
You are measuring the fixture and the DUT, calibrate using the fixture connected. When you adjusted the stimulus you forced the VNA to do interpolation, not that important in this case but generally a bad practice.
@ve6wo
@ve6wo Год назад
Yes, but at these low frequencies, I challenge you to do the same test twice, using the correct method and then using the ‘bad practice’ method… and tell me if you see any kind of significant difference. ;-)
@galileo_rs
@galileo_rs Год назад
@@ve6wo Generally true but it depends on the DUT. For example try measuring a 10K resistor using a "S21 method" and comparing the results that you get with an ideal model (SimSmith is great for that). For example, place the test jig directly at port 2 VS the usual way of using a coax pigtail. Now, does any of that matter for amateur radio usage, not really but it is good to know how to do it properly and it is a fun experiment.
@ve6wo
@ve6wo Год назад
@@galileo_rs I agree
@galileo_rs
@galileo_rs Год назад
@@ve6wo 73 YT3ART
Далее
nanoVNA - Measuring Inductors and Capacitors (Vers. 3)
11:18
Measure Capacitance and Inductance with a NanoVNA
7:05
1 класс vs 11 класс  (игрушка)
00:30
Просмотров 1,4 млн
Lossless Impedance Matching - Part1/2
20:50
Просмотров 31 тыс.
G4NSJ - Checking SWR Antenna resonance NanoVNA H4
15:29
Everything You Need to Know about Breadboards
3:25
Просмотров 204 тыс.
How to use a nanoVNA as a grid dip meter.
12:38
Просмотров 14 тыс.
Inductor Tester
10:01
Просмотров 76 тыс.
Не обзор DJI Osmo Pocket 3 Creator Combo
1:00
Lost Vape Ursa Pocket
0:17
Просмотров 88 тыс.
How charged your battery?
0:14
Просмотров 3,6 млн
wireless switch without wires part 6
0:49
Просмотров 1,2 млн