Narrowing a Ford 8.8 | 1965 Mustang #3

Подписаться 12 тыс.

Просмотров 7 тыс.

50% 1

www.buymeacoff...
patreon.com/Ro...
ROOKIE MERCH: kmpaint.shop/c...
Instagram: ⁠@rookie__pilot
This was one of the most intense fab work I've done so far, this ford 8.8 came out of an explorer and is going into our beloved #3 65 mustang. Maybe a 4 link soon?
Some people have also asked if I have a wishlist, so here you go!
www.amazon.com...
Angel Robles
P.O. Box 27794
Tucson AZ 85726
Angel Robles
1501 S Cherrybell Strav
#27794
Tucson, AZ 85726

Авто/Мото

Опубликовано:

30 сен 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 77

@murraymiskelly1813 11 месяцев назад

Always great to see you work things out. BTW your measuring tape is correct with the loose end; it slides so you can do a butt measure, or a hook measure and it allows for the thickness of the end piece.

@rookie__pilot 11 месяцев назад

Thank you!

@sn95_slobra 11 месяцев назад

For the clocking, you could always go back and look at your footage. You wrote "like, subscribe" on the tape. You could line that up same as on the camera, then add your clocking marks.

@rookie__pilot 11 месяцев назад

If it wasnt for those words i would have 100% would have welded it 180 degrees off. So you’re absolutely right! 😂

@brianbrown543 11 месяцев назад

When I was a fabricator we had many days where we had to do a LOT of heavy grinding. If I ever forgot to put a dust mask on I, and many of my coworkers, would end up with what we called "Black Booger Syndrome".

@rookie__pilot 11 месяцев назад

I got the black boogies even with the mask lol!

@deopersad2915 11 месяцев назад

Cool 😎 I looked into nowing a diff many year's ago, and had books from hotroders and engineers they had set up a drop saw and made sure it was straight to cut and bolted into a jig to keep it straight , but I never did one lol back then to lots of guys doing them so could buy one already done , but if I do a project I may need to do this in future?

@bronxsmash8869 11 месяцев назад

Looking good, Angel Pumkin Cake! And the only thing worse than gear oil is burnt gear oil😢

@rookie__pilot 11 месяцев назад

That’s definitely right lol

@robertlugo3388 11 месяцев назад

Your tape measure is working correctly. The tab is designed to live like that. That slop compensates for the thickness of the tab, if you are using it in a push or pull mode.

@rookie__pilot 11 месяцев назад

thanks !

@madDadMusic 7 месяцев назад

Tape measure ends slide on purpose so when you hook them on something, you get the right length. It moves exactly the width of the lip.

@magikahn 11 месяцев назад

You need some better metrology tools...

@thyubernoob 9 месяцев назад

I've never messed with a dif, is there a reason you couldn't pull the axle tube out of the pumpkin and cut and press it back in????

@rookie__pilot 9 месяцев назад

That is definitely a good option which would probably leave a cleaner result, but requires a press big enough to push the axle tube back in!

@MS-hd8yq 11 месяцев назад

Great job Angel. I'm guessing you'll be able to use the same length axle on both sides, since they're the same length now?

@rookie__pilot 11 месяцев назад

Correct! We have to go on a fieldtrip to the junkyard

@MS-hd8yq 11 месяцев назад

@@rookie__pilot noice 👍

@louholtman9202 11 месяцев назад

I would had made a piece of strip with the correct length as a caliber so you didn't have to measure it every time with the ruler.

@rookie__pilot 11 месяцев назад

Thats perfect, will do that next time

@jorgevivas6031 2 месяца назад

hello from Venezuela, your video its perfect, its made for dummies ,i will make these job for a ford falcon 1961 the measurements are the same?? i enjoy this video, good material , thanks you

@fishflash1 11 месяцев назад

Very good fabrication work.

@keonikaig9247 11 месяцев назад

Nice work...👍🤠

@hughjohnson2674 7 месяцев назад

Hey Man, I like your channel and your face. After having one disc explode in your face, please put the safety guards back on your damned grinder. One slip and ain’t AFC anymore!

@JH-oh1in 5 месяцев назад

If you have a next time use the axle if you can get the clip in you can make it work, Straight and square is a bigger deal. Cars are not built that precisely back in the day.

@Dontfearthereaper001 5 месяцев назад

Always use hose clamps, not tape for cutting round tubes bare minimum

@westparley 10 месяцев назад

Maybe you mention it in the video, but what is the overall length of the axel after you make the modifications?

@emmanueljimenez5141 5 месяцев назад

Hey bro, nice work. One question, how did you fix the long axle to fit back?

@rookie__pilot 5 месяцев назад

You have to use another short axle, i pulled the extra from the junkyard ✌🏼

@emmanueljimenez5141 5 месяцев назад

@@rookie__pilot like the short side but from another rear end?mmmm ...... Smart!

@emmanueljimenez5141 4 месяца назад

@@rookie__pilot one more question, where did you get the bracket to mount the new rear end?

@bjsteg79 3 месяца назад

For those who don't know: Gear oil smells like cat pee

@thekatmann9730 11 месяцев назад

Great to see your clamps in action again! Glad I could help out.. Hopefully some more folks will jump on board, and you can snag that sweet floor jack!

@rookie__pilot 11 месяцев назад

without them I definitely could not have done this job, huge thanks again! Yes hopefully cause with age mine isn't staying up lol

@johngidman4574 11 месяцев назад

Might want to check the clutch pack in that. They're a wear item and many are worn out by the time they get to the wrecker stage. Better than putting in the car only to find out you don't have a LSD. 😊

@rookie__pilot 11 месяцев назад

Great point, thanks!

@ArniVidar 11 месяцев назад

Has a tape measure that has both inches and millimeters, still uses the less accurate inches. 😅 Looking good! I hope you get some sponsors at SEMA. 🙂

@robertbeckler5058 28 дней назад

Sweet

@genemounce8302 8 месяцев назад

..and it was at this point in time, @20:30, he should have cleaned out the axle tube prior to welding. LOL Good video dude. I'm doing the same thing to my L33 swap TKX '68 Coupe !

@rookie__pilot 8 месяцев назад

Exactly!! 😂😂😂 Hell yea that sounds like a fun project!

@davidlegault9745 11 месяцев назад

Nice job Angel. I agree with you about the more powerful welder for next time - better safe than sorry. I also agree with you about the smell of gear oil, just watching you I could smell it. Good Luck at SEMA. Regards, Dave

@rookie__pilot 11 месяцев назад

Thanks Dave!

@joedirt3762 11 месяцев назад

I absolutely hate the smell of gear oil as well. It is probably the worst lubrication smell in the lubricant family. Your videos are awesome though. I plan on building a mustang 2 for drifting and I'm loving this up-to-date mechanical knowledge from your videos. Keep it up!

@rookie__pilot 11 месяцев назад

I agree! Hell yea man thats sounds like a badass build! Thanks man, I appreciate it!

@bobmiller7426 11 месяцев назад

I really enjoyed the way you attacked this scary project. Good luck at SEMA! Keep positive and work like crazy. (Because sponsors is work!)

@rookie__pilot 11 месяцев назад

Thanks Bob!

@wallyodom8254 2 месяца назад

The hook on the end of your tape measure moves the thickness of it to allow for hook and butt measuring..that's what makes it accurate

@philthy8150 9 месяцев назад

Building a work bench would be a good idea

@kirktruman6707 11 месяцев назад

Hey Angel awesome job I would have been nervous too. And now for the hard part of placing and welding the brackets in the right spots, lol sorry did not mean to make you nervous.

@rookie__pilot 11 месяцев назад

Well thanks kirk 😂

@darrencatenacci2737 11 месяцев назад

Great job! Hopefully a 4 link isn’t too bad to find. I was curious when you’d realize you forgot to mark that line.

@rookie__pilot 11 месяцев назад

Haha thanks!

@tommcl8548 11 месяцев назад

👍👊

@rookie__pilot 11 месяцев назад

🤘🏼👍🏻

@NikMitchell 11 месяцев назад

ayo, i didn't expect a callback! haha thanks man - loving this project so much! /highfive

@rookie__pilot 11 месяцев назад

🤘🏼

@wongway40 11 месяцев назад

love this video - as for the doodle oil smell, next time, cut up an onion before hand, or.... light a match! 😝

@rookie__pilot 11 месяцев назад

Good idea!! maybe light a candle 🤣

@garyworokevich2524 11 месяцев назад

Great work Angel

@1944chevytruck 11 месяцев назад

Good job! thats how you learn from your midtakes...

@rookie__pilot 11 месяцев назад

Yessir!

@jeffreyandreas7514 11 месяцев назад

Wow! Excellent attention to detail and a great result, very nicely done!

@rookie__pilot 11 месяцев назад

Thank you! Cheers!

@toobusy63 11 месяцев назад

Thanks for the daily dose of GEAR OIL & 2 7/8 17 3/8😂🙌🙌

@rookie__pilot 11 месяцев назад

Lol, i should have done a count of how many times i said either 😂

@toobusy63 11 месяцев назад

@@rookie__pilot 😆

@kingsleywray6632 5 месяцев назад

It was your first time. Having already seen later videos I know you have learned loads - and shared this with the rest of us

@graemelliott3942 11 месяцев назад

You’re a good welder! That mustang is going to be a sweet ride!

@rookie__pilot 11 месяцев назад

Thanks graem!

@graemelliott3942 11 месяцев назад

@@rookie__pilot hope to see you at SEMA!

@mudmucks 11 месяцев назад

Someone please explain to Angel how a measuring tape works :) Did you measure the runout at the end of the axle tube? Im assuming you can buy shorter axles, or you gonna have to cut and weld one of those too :) :) ?

@rookie__pilot 11 месяцев назад

Someone already explained lol, you can use another passenger side axel

@mudmucks 11 месяцев назад

@@rookie__pilotanother axle from the other side - of course! 😁