Neglected Bmw E36 M3 Evo in for Restoration! - Part 4 - Finish line ! 

Great transformation! I have a real soft spot for E36's and I'm glad another one has been saved :)

Look how filthy the engine bay is, and he works on it day and night. Good lord!

Nice job Ed, but please flip the side indicators to the opposite side so they are installed correctly. 🙏

OMG! I have this same car but mine is the convertible (w some mods, I live in the mountains). Estoril blue with black interior. I love my blue beauty. You will smile every time u drive it! My only complaint is the clutch spring has popped a few times & the steering pump has been an issue but other than that its been solid! A hobbyists (badass)dream!

Incredible work.

10k all in, not a penny less..!

Very clean my friend 👌🏻

awesome job!!!

As for labour, I would say 35-40 hours at whatever your shop rate is...

Yeh me i like M539 Too but he just throws £5 grand here and £2 grand there. This is my way of doing things . I learn a lot from you .

Hallo grüß Dich ich habe mich gerade etwas amüsiert aber ich freue mich dass du den Tipp von mir zu dir zu Herzen nimmst und die Bremsscheiben jetzt richtig eingebaut hast daumen hoch dafür schönes Video gut dass du dieses Fahrzeug wieder auf die Straße bringst ich hatte auch schon drei jetzt kannst du auch richtig bremsen und sie werden schön kühl bleiben bei Belastung good job

sick! 🔥

Would I be wrong to say the total labor came under 4.5k? Incredible work you did. I binged on ALL 4 episodes. I have an E36 2.8i that's in a worse state that this one. How does one reach out for further advice?

Salut, good job.👌👍🚗

The bottom trim comes from BMW with the little piece on the end already attached I bought both I think it was about £150 for two

From ttk ❤ , nice job sir 🎉

Funny comment on the sideblinkers... 😁 not that a bmw driver will need it... 🤣

4.5k labour easy

Labour would be way more than the prices of the parts... My guess is 7000 quid for the work alone. Some parts are really inexpensive, like the valve stem seals, which are only 100 quid or so from BMW. But doing the job at a BMW shop would be around 3-4K i reckon...

Didn't know Snapon was popular in the UK. How about Hazet or Stahlwille toolbox? must be cheaper

💪👍😎

Veiksmi darbā! 😘😘😘

I prefer this channel to M539 because you aren't just throwing money at cars. On the discs, the F01 7 Series is another car with handed discs - fit them the wrong way and 500 miles later they are warped and scrap. I also re-grease old belt rollers. The side repeaters are on the wrong way around though! When you fit the eccentric wishbone bushes, fit them so that the hole is closer to the outside of the car. That moves the outer balljoint forwards, moves the wheel forwards and increases the castor angle.

another 5k :)

Labs darbs draugs

You are missing 2 panels under the car

The indicators (side repeaters) are on the wrong way around!

I use dental floss and a hot air gun to remove those glued on badges

Bro, please drop link for door handle rubbers on eBay

Thousand

Labour cost...about £2k...that's all I'm gonna pay.

labour 1500 + VAT

2800 pund

How you managed to fail mot at this place 😂

2k labour

Labour 3k

£3k without VAT for Labour

£3500 labour

parts=labour

obviously you dont know how to install handle trims