Ninebot Max G30P Error 14 and 15 Fix 

Had the same problem. Just picked up the scooter and dropped it on its tires from knee high. Fixed it for now. If it happens again, I’ll open it up and replace the connectors. Thanks again!!!

Thanks for this. We put pillow stuffing inside to keep wires from bouncing.

Thanks for the video. my scooted fell over and started giving me the error 15 message. Just used this to fix my scooter. Bought tamper T10 torx screwdriver. Opened it up and the cable was literally unplugged. Plugged it back in and right back to working.

Had my 1st error code 15 today 24Sept2021. ° The initial problem began when dash and scooter didn't turn on when pressing the button. ° Eventually it turned on, then shortly after beginning to ride the scooter decelerated itself a few times while I was trying to accelerate. ° Then the red 15 began flashing. ° I turned it off and on a few times, but the flashing 15 kept appearing. ° I did a reset after remembering reading about it, and it worked. I made it home and found your vid. ° Watching your video was helpful in confirming what I guessed was the cause. ° Inspecting the issue I now think that hanging any bag over the handlebars can be one cause of such a problem. As when a bag strap/handle finds its way into a small exposed piece of electrical wiring from the brake it can put just enough tension on the connection as to disturb it. Thanks, good video.

Dude thank you! First 22 seconds of video I fixed it. Wow

If it didn't solve the problem, try disconnecting all the 3 wires, and connect them back. Error 14 worked that way for me. Anyways thanks for the video, helped out! Appreciated man!

I had ‘error 15’ showing, done what you did in the video, and it’s cleared it. Those wires was stuffed/crammed into a grey rubber cup with some right angle bends to them.So I took them out of that grey cup and tape each connector, and free those wires so the do not have such a bend on them, THANKS MATE 👍🏾🇬🇧

Thanks man. Just now got an error 15. Followed the video the cords were bent but could replicate the error. So i straightened them. And then put it back together. And it seems to be fixed.

Bro you are the best!! Wish I could give your video more likes. Just fixed my Segway in literally 5 minutes. Many thanks!!

Thank you for this great video. We were able to fix Error 14 👍🏻

If the black power cord is broken, error 14 will also occur. Thanks for the tip, I finally fixed the issue！！！THANK YOU！！！！

So much clearer and more specific than any other video/site I found (size of each screwdriver, noting zip tie that needs to be cut, etc.). Thank you.

if its really just as simple as that and as fragile as that im legitimately surprised i didnt get this any sooner. i fell off twice HARD (both my fault) dropped it on its side plenty of times and didnt start getting this until now 4 years after i first bought the scooter

So Super Easy and Free. You're a Genius . Thank You.

wow man worked like a charm, you were right on the tight angles on the cables. xiaomi m365

worked for me. the connection is bad right up next to the display connection - i can tell that my fix won't hold. i'm gonna have to figure out how to fix the blue brake wire right as it enter the solder connection to the board. oh joy. Still, thank you for pointing me in the right direction.

Thank you!!! Hoping this will fix the one that was given to me!!!! 🎉😃🎉

You just saved me a throttle replacement. Many thanks for that! 👍

I wanna buy you a beer man you just solved something that's been bugging me for months.

Think the person who had the scooter before me couldnt figure out the problem and replaced the handle with the wrong one, and to rid of the error codes 14 & 15 I have to find the correct replacement as I checked every video in history and tried every single trick haha

This video saved me.... Thankyousoomuch Sir... Godbless you more🙏

Loving your old skool casio watch :)

Thank you for sharing you save my time and I fixed my segway easily 🙏🙏🙏

Applied the fix as you described it and it worked! Thank you sir!

Thank you bro u saved me 2 mhonts its working

Thank you so much! Best video ever!

You should probably have cut and soldered these.. once a connection like that is bad it will never be fully ok by just bending in my experience: issue always returns at some point.

You just saved my life thanks man 👍🏾

Thanks for the video. It works. error 14 solved.

i had the same problem, sometime works and some time shome error 15 and the scooter stop, i usually press the break and run again.

Thx mate, perfect advice.

I didn't get the red wrench, I got the red key symbol flashing, what does that mean?

This worked for me, thanks!!

hey i done that to mine was having same issue with mine will ride it later and see if it has fixed it but besides that thanks dude it helped

Thanks for the help!!!!

Hello,my scooter is showing the exact same symptoms,but is flashing an error 16,which I can't find a solution too, any ideas?

You help me a lot, thank yuu very much

Thanks this helped. Nice Casio btw

hello, my scooter is stuck on 20km/h (12-13mp/h) in every mode eco,drive and sport what can i do?

Thank you !

I have this error after send my scooter to friend ask him repair. But I can use normal not a problem, only error 14 appear. Thanks upload the video will fix ASAP.

Thank you man 😊

Workss thanks

Good job

Thankfully I don’t have any problems yet

it is not a phillips head for the board. It looks like a star with security . Any idea what size bit it is? Thanks

Questo G30 Max costa molto e da errori cos'ì stupidi? complimenti alla segway per le finiture al risparmio. Grazie per la soluzione.

Many thanks 🐾🐾🐾

Good video! Anybody knows how can i reset the mileage of my scooter (not selling reasons) please?

What do I do if my handle bars aren’t straight too

Thanks 👍🏾

Now do a tutorial on Ninebot F40e/F40 on how to get the screen out.

There is a decrease in the speed, the speed was 25 km before, and now the speed has become 22 km in the fast sports mode, how can I restore the speed as it was in the first 25 km

I have a new throttle but still im getting this error every day ! dont know what is wrong !

I would just solder them and you’ll be set for life !.!.

Hey for some reason mine wasn't that easy where else should I check?

my scooter screen doesnt turn on at all ninebot max plus what could be been siting ayear trying to fix it myself

What is its not that? What would be the next step? I'm getting the 15 error but nothing I do with the wires, like you show, does anything.

Any other options got error 14 nothing has changed

Thanks

I have error 18, what's wrong with it?

Hi my scooter is new then sudenly when i turn on it start beeping non stop and not showing any error codes its just freeze all can someone help me pls.

Hola. En la Pantalla abajo de Km me aparece ECO alguien sabe que sucede?

Why dose mine say Error 18

i had a code 16 can somebody help

I have error 10

My scooter charges but stop after a few minutes can this be the same problem it charges but only at 95 percent

Very since scooter

Mine scooter sometimes shows the same error and sometimes not . Where I can get the tool to open the display ? I also want to fix the error, I am not able to open the display without that specific tool.please help me.

Just solder them.

Mein error 10 🤷‍♂️

what a horrible company, brand new scooter and Bluetooth not working !

THANK YOU!

Thank you!