Kevin demonstrates a basic setup and basic operation of Novastar's NovaLCT platform, going over the Sending card, Receiving card, and Screen Connection pages to get up and running quickly and easily
Great tutortial Kevin. We rent from nationwide anytime we have bigger events and the gear is always in immaculate condition. I wish this tutorial was around 5-10 years ago. Back then the only tutorials/training were all in chinese.
Great video very informative and helpful!! I struggled for two days trying to get the screen setup right. After watching the video. done in ten minutes! Thank you!!
Hi Kevin, Great video, I am looking to connect a large screen and power it using 2 Novastar VX4S-N sending cards, these sending cards dont have the capacity to run the screen on their own. I can see on your screen configuration it gives you multiple sending cards to draw your cable routing on, how do you wire these up so that you can run these in parallel? Kind regards, Joe
Amazing content. Really helpful. I have an LED wall and ill like to place a Square LED (500x500) 8 of them below and place a Rectangular LED (500x1000) above Is this possible to configure such?
Hi Kevin, We have a large 10 cabinet LED screen and one of the Novastar MVR208 has been damaged. We have seperate new card? Would you be able to help us in programming the new card. If yes please reply and we can be connected directly.
(Sorry if I make some mistakes writting this message, english isn't my first language) Hey, I'm mostly a Streaming operator here in Guatemala, but I'm starting to transition to led screen mapping as well. I have people that will rent me the led modules and cabling but I'm planning on buying my own LED Processor, so I already decided to buy the Novastar VX600, but I have a question I couldn't find in the whole internet: I'm aware that I need to set my led's custom resolution to the processor and to the novastar software, so I can finally do the mapping on my mapping software (for example: Resolume Arena) but the question is: Will my pc will ever recognize the led's custom resolution on the windows settings? (Like when you use a custom monitor with a special resolution, like an ultra-wide monitor) So it fits the canvas perfectly, or will it always detects it as a 1920x1080p monitor? And if so doesn't it affect the overall quality of the mapping? because what the pc is detecting is not the same resolution as the overall resolution of the led screen? or should I try to make it fit with my mapping software?
Great content as always Kevin. Thank you for sharing your knowledge. I am trying to revive an old LED wall using elation EVP762 cabinets. I cannot find an .rcfgx file anywhere in our systems and cannot pull the .rcfg or .rcfgx file from a cabinet module through NovastarLCT (errors). Any suggestions?
i am try to configure a screen, Specs say resolution for this screen is 416*224 dots. But maximum in the configuration tool is 373*256. The original config file is not available. Any idea how i can adjust the thresholds?
Is it possible that the config pattern on port 2 is different from port 1? When I try this on demo whatever config in port 1 become the same with port 2. And if I config a pattern in port 2, the pattern in port 1 copies it.
Hi, I am very much a rookie with all this! I have a Nova Star VS 1, which I'm told is not released in the US? I bought my screen directly from China. The out put to my screen is to big! I do not see a fit to screen, can you help?
After screen configuration, when i send screen configuration it show this msg : failed to send screen information,current display mode is 0x0px . Plz help me, thé device is VX400
Hello I have a serious problem. I made a mistake causing the controller to go back to factory defaults. After which I took the configuration from a different controller with identical setup, uploaded and now the screen is completely black. Before going black the screen was artifacting in may collars then it went black. Any suggestions ?
Yes, I managed to fix this problem a while ago. Therefore, my memory is a bit foggy. But what my mistake was restoring the configuration and not sending it. One way to confirm you sent the configuration is to pull the config after your pushed the config to make sure it's on the unit. @wedontcare7281
Are you located anywhere near Houston? I would like to hire you to help me configure my led screens on my truck if you are around the houston area or if you can maybe zoom call with me because I’m not doing something right. I have video being split on either end and with a second video in between of a video. Hard to explain without seeing what I’m talking about but the videos are intertwined with each other.
@@kevinringvideoi tried admin or 666 i can't log in, how to reset the password? i tried to uninstall and reinstall still can't log in with the password of "admin" or "666" please help
