Orca Slicer Pressure Advance Testing and Calibration: Unlock Sharper Prints (Ultimate Guide)

Подписаться 6 тыс.

Просмотров 9 тыс.

50% 1

Orca Slicer Pressure Advance Testing: Level Up Your 3D Printing: In-Depth
This in-depth video will explore pressure advance calibration tuning specifically for OrcaSlicer 3D printing software.
Pressure advance is a powerful setting that can significantly improve your 3D print quality by reducing stringing and blobs. But calibrating it can seem daunting. This video will be your ultimate guide, walking you through the entire process in OrcaSlicer from start to finish.
Whether you're a beginner looking to understand the basics or an experienced user wanting to optimize your prints, this video will equip you with the knowledge and techniques to master pressure advance calibration in OrcaSlicer. Get ready to unlock sharper, cleaner, and higher-quality 3D prints!
References:
Ellis' Print Tuning Guide: ellis3dp.com/P...
Quick Links:
Minilam3DP Klipper Calibration Website: minimal3dp.com/
Klipper Calibration Spreadsheet: tinyurl.com/28...
Email: minimal3dp@gmail.com.
Minimal 3DP on RU-vid: / @minimal3dp
NEED HELP?
Schedule a FREE 15-minute Google Meet Consultation:
calendly.com/m...
NEED MORE HELP? Contact me regarding a 1-2 Help Session. I can be reached at minimal3dp@gmail.com.
* Note: I may earn a commission at no extra cost if you click an affiliate link and purchase. *

Опубликовано:

12 сен 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 36

@adamsvette 3 месяца назад

Your pressure advance K value can change depending on filament type AND temperature. Just something to keep in mind. The K value you determine is specifically for THAT filament at THAT temperature.

@minimal3dp 3 месяца назад

Thanks foir the feedback.

@JohnStruemph 3 месяца назад

Thanks Mike! Great vid and info! Be well and happy printing!

@minimal3dp 3 месяца назад

Thanks for the kind words. I appreciate it.

@thebrelon 3 месяца назад

I find the line test is the better of the 3. easier to read and less difficult to decide what's good and what's not

@minimal3dp 3 месяца назад

@@thebrelon I like either of the line based tests. My easier and quicker than the tower.

@andreferrato Месяц назад

Thanks for the worksheet.

@minimal3dp Месяц назад

I hope it helps.

@contomo5710 3 месяца назад

you know, the guide and explenations are so good, im not even gonna complain about the mic peaking^^

@minimal3dp 3 месяца назад

Thanks for the feedback. I struggle horribly with sounds.

@contomo5710 3 месяца назад

@@minimal3dp its totally acceptable, ive watched stuff with way worse audio with not as good content before, i just may be a lil picky when it comes to sound! :P

@jeffellis1149 3 месяца назад

Great video, thanks! I use a cheap usb microscope for examining the results. Very revealing for stuff like this.

@minimal3dp 3 месяца назад

Glad it was helpful!

@stefanguiton 3 месяца назад

Excellent videos as always

@minimal3dp 3 месяца назад

Glad you like them!

@mza1979m Месяц назад

Can I provide you with some constructive criticism? I highly highly highly suggest you find a way to improve the visual quality of your video(s). I've only watched this video. I don't know about the rest. I have it set to the highest quality (1080p), but the picture quality is very fuzzy and looks like a video from 90's. I think it's especially important with 3D printing videos, so we can see important details. I don't know if it's your camera equipment or settings or what... The audio quality as well seems quite low. Thanks!

@minimal3dp Месяц назад

Your criticism is welcome and warranted. I really appreciate your feedback. Unfortunately, both my video and audio are what I can afford at the moment. I am trying to save for better equipment, but it is slow going. I typically need to buy items to do videos about and save, so it's not super fast for me. I am going to try to sell a printer to generate some capital to invest. I have also discovered that my hearing is not great, leading to some quality issues that I am not detecting. A friend has offered to assist me, and I scheduled a hearing appt later this month.

@stevehanwright481 3 месяца назад

Hey i just found a neat trick print the PA line test then look at it with the lines running left to right but at about 10 to 30 degrees to the build plate it real help tell when the lines go from bad to worst then put you finger about half way between

@minimal3dp 3 месяца назад

Thanks for sharing. I will give it a try.

@stevehanwright481 3 месяца назад

like you said the line and pattern method seem the best to get a definitive result, like Ellis states one you have an idea for a range you can reprint a range from .02 to .04 in .001 intervals if you like ..

@minimal3dp 3 месяца назад

I am wondering at what decimal place the adjustments stop making a difference.

@Caldoric Месяц назад

Question: does your spreadsheet accommodate other firmware types, like Marlin and stuff?

@minimal3dp Месяц назад

No itsoes not. It is designed for Klipper. Take a look at the TeachingTech calibration site. It is ideal for marlin.

@stevehanwright481 3 месяца назад

great video you have new subscriber

@minimal3dp 3 месяца назад

Thanks for the sub!

@user-gh8tw1sv7o 2 месяца назад

Need turn off acceleration? (Klipper document say this) In slicer ...or need put codes to console before PA? (Klipper document says this)

@minimal3dp 2 месяца назад

I turn it on in the slicer and don't put it in my klipper printer.cfg.

@ruckus226 2 месяца назад

what are the slicer settings suppose to be?

@minimal3dp 2 месяца назад

What do you mean?

@DaveYoutube-qc3qy 3 месяца назад

I’m assuming speed and acceleration settings would affect these calculations?

@minimal3dp 3 месяца назад

It will. You.want both set to your preferred values before you start the PA tests.

@RoofusKit Месяц назад

I think the PA Pattern test is a lot easier to read.

@jeffwhite9001 Месяц назад

Didn'y you do it wrong though? You have to do each test with pressure advance turned off??

@minimal3dp Месяц назад

I thought I did disable via the config. I will check.

@AndrewAHayes 2 месяца назад

You would think that once you had completed and entered in your manual calibration results that the auto calibration would centre around this new value, but NO! it continues to use the three values it always has to test the flow!

@minimal3dp 2 месяца назад

I believe most of the test use "standard" values.