Our Brand NEW Paint Booth Is Finished And Ready For Its First Paint Job!!! 

From a stone driveway to professional shop and paint booth. You boys have come a long way. Props!

i think a metallic midnight purple would look really sick on the urus, at night it would look black and in the daytime those metallics would really make the purple pop.

I'm an electrician, your new disconnect is wired backwards. The feed from your service equipment should go to the top of the switch, equipment goes to the bottom. Your enthusiasm and work ethic are second to none. Love your vids.

Nice job, I would get that phase converter off the ground and I believe that conduit is supposed to be at least 18 inches down under an asphalt driveway.

Y’all boys need to start putting out videos on Sunday morning again. I really miss getting up and grabbing some coffee and waiting for your video to post. Gets my day started.

You should have buried a electrical warning tape a couple of inches over the conduit, and make sure to add the piping to a property map so both you and a potential new owner of the property in the future know were it is.. just a tip (eng not my first language)

make sure to get a Steel Fence around the Fan for extra security for ur pets

Just a thought.. pour another pad move the boat n truck over. Then setup a smaller booth for painting parts w/ a separate mixing station area in between both booths. 🤔 it’s super efficient and allows a couple projects w compartmentalization.

Ive been watching you guys for 5 years and Its hard to get used to the less frequent videos.

You guys might want to check your local codes because the electrical lines have to be 18" under ground where i live. Yours may need to be 24" even under the driveway. Also there should be a junction box where the 110 lines come off your main run to the paint booth. You guys did a good job but the conduit needs to be alot deeper.

Keep in mind that you can't paint in the winter when the weather is cold because the booth will need heated make-up air during the paint cycle. Infrared heaters will not work, as they only heat the objects (vehicle), not the air. Infrared is good for baking after the car is painted, but you will need enough lamps to heat the whole car evenly. When you are painting during the summer months when it is warm the air coming into the booth will be fine, but when it is cold outside, picture painting in 40 degrees to 50degrees. The paint will run right off the rockers onto the floor of the booth. Your next major purchase is going to be a furnace. A spray booth furnace is 900,000 to 1,000,000 BTU's. You could either go with Propane, Natural gas if it available on your street, or oil. The bake cycle runs for 30 minutes. The natural gas consumption for a 950,000 BTU furnace for 30 minutes is $17 to $20 dollars. which will not break the bank. Propane is slightly higher. You guys also need to bolt that phase converter to the concrete. I saw how it jumps when you start it, you don't want it dancing around while it is running.

The flexible conduit is good. Per electrical code , you can't shove a flexible conduit into a 2in PVC. You need to put a junction box with the appropriate connectors in. Now looking at your fan connections. You will need a box in between the connections also with a Romex connector for each of Romex or cable! After time these bad connections can cause you problems!

While yous are on break so much i started finding cool Build channels

As a 30+ year electrician I have to say that your installation looks not to bad. I did notice a couple big issues that wouldn’t pass inspection in Canada. The main concern is the new disconnect switch. Your feed wires should have been connected to the top of the switch and the load wires on the bottom. Yes it works how you have it but it’s a safety issue for the next electrician if he doesn’t notice. The other thing is the depth of the conduit under the driveway should be deeper (3ft) so it doesn’t break.

I love it. Everyone commenting is a professional electrician all of a sudden…just like they were all contractors and retaining wall experts .

Big up to Pops, he’s living the dream with his family! I am loving everything about you guys, this channel is edutaining and inspiring either ways. Best channel I ever subscribe! Peace..South Africa

Just went back and watched some of your old GTR and Viper builds. I miss the old style simple content you used to do.

You should have laid caution tape onto of the conduit before you backed filled so if anyone digs there since you didn’t go deep enough I might have given you some protection

The lack of videos dropping is upsetting. Been watching you guys since I was a sophomore in high school. Im now 22. I miss the consistent videos, or atleast knowing when your vids will drop.

I always love seeing Pops out there working with you guys. It was the best time of my life when I could go to my dad's shop and work on cars with him. I miss doing that every day

those cables need to be at least 18 inches deep unless they are in metal conduit

You are going to need to add a special room attached to the paint booth to mix your paint etc. The final addition.

Doesn’t your building code require you to dig a 36” deep trench to put your electrical conduit in under your driveway. This keeps the conduit from getting broken when you drive over It in the driveway. Be prepared to have electrical issues possibly in the future. Remember that there is never enough time to do it right, but always enough time to do it over.😮

Great that the install is done, but I hope the electrical doesn't need to be inspected. 18" deep minimum in a pvc conduit in Chattanooga...

Think ive had enough of this. Plenty of other channels. Thanks for the last few years. Ciao.

Boy! I don’t think I would make that transformer permanent on the concrete! I would have it installed on a platform where it’s off the ground

Pops is living the dream, getting to spend all his time with his sons, make sure to enjoy these amazing moments with him, as you never know when you will no longer have the opportunity...

You guys are acting like little kids during christmas ...... I LOVE IT! Good to see you can be authentic happy if something good comes along. And it's so nice to see how you're involving dad and appriciate him for all his efforts!

I was OCDing about the carport walls, glad you're gunna waterproof the exposed electrical area, don't leave it too long! As for the new color, go for a color you've never done before. black or purple pearl.

Safety 3rd guys! 3 phase for machinery is 'usually' 480v. And it hurts, I got a belt off it about 25 years ago. Burn to my hand & heart was beating irregular. I think that's what they said, that's the only time for 3 phase 480v, probably 15 times 240v. That's like a tickle compared to 3 phase! Keep it up guys & love to pops!

Congrats on the new paint booth. I love that you guys aren’t afraid to tackle and project. I like the purple Lamborghini idea.

They make a special plastic for booth walls thats nice and tight and instead of over spray landing on brand new walls you can spray directly on the plastic and whenever it's full of over spray remove plastic and add new, bc let me tell u, to get that perfect brand new booth wall finish is hard and it sucks having to repaint it. Hope you guys see this!!

Even if you don’t need it that day I find it’s always best to lay a conduit under a new drive as a matter of course. These days IT / fibre optic installers charge the earth to do it so it’s always a money saver in the end. (Always run a pull through rope through at the same time and just keep it wrapped up until the day someone needs it..)

That silver on the driver’s side really brings out the body lines and defines the Lambo shapes and design. Beautiful paint booth, congrats guys! 👌😉

Those under-drive boring machines are absolutely brilliant! I think if I needed to hire one for the day I would probably measure the drive width I needed and get that number of extensions! It would save a whole day wasted! Great work boys!

We waiting ✋️ 😌 😮

You need to paint it a metallic black with high gloss clear coat ! Would really look epic !! 👏

Congratulations on the new paint booth! Its amazing to see the hard work and dedication that went into creating this fantastic space. Can't wait to witness the magic of the first paint job - heres to countless vibrant transformations ahead!

So happy with the paint booth finished. But Guys I don’t even know now when you are going to upload a video. I am kind of lost. I love you show anyways.

Glue the conduits? Legally that can’t be deep enough either surely

Where are the ground rods? Is the gate opener power direct burial cable? Is the pipe size rated for the amount of pipe you ran? Is the pipe 18" deep?

Great job guys! You made it through all of the obstacles by yourselves. Be proud!

I love how your dad works with you guys. What a blessing for you all.

Always amazed at your ability to figure things out.

Cool, but sure doesn't look like code required 18" burial depth. Could have gone with RMC/IMC pipe and done 6". A few hundred bucks more and you would have had it done to code.

@goonzquad You guys should have a side wall enclosure over the power equipment because it's open to sideways rain at the moment as well as moisture perhaps getting into the control board. Normally these control boards if inside a factory or garage they are in a separate room from the outside to be legal.

House of color paint with multi layer candy purple or red would be a great way to take your painting skills to the next level.

The paint booth takes all your projects to the next level. Superb guys, well done.

@goonzquad You need a cover over that control panel!! Covers it from weather, moisture, and protects from unauthorized people messing with it!

“Murdered Out” black would look badass on the Urus. Maybe a combo of gloss and matte but all black. Super sinister looking.

Guys i know your whole journey is documented video by video but i really think you should either post a video of the first build you did at Mom & Pop's house or maybe a compilation video from then until now. this is just incredible and Huge congratulations! Very Inspiring!

Instead of building a storage spot for parts you can always just put a 45foot shipping container beside the slab. You can sometimes find new ones without rust and dents for a fairly good price and it’s portable so you can move it around or take it with you if you decide to go bigger on the next garage

Old man is the reason I have subscribed to your channel ❤️ He works hard take care of things and has solution for every situation 🎉❤

Good job fellas make sure that building/eq is grounded, looking forward to seeing some sprays!

I love you Guys, and I love Pops and Mom, I wish I had parents like yours, and it makes me so happy to see you spend time with pops and being able to buy him and your Family what ever they need, God bless you guys, PS I wanna see videos 7 days a week, 😂 when I come home from work.

I love that you guys show drilling under the roadway & all the little extras like going to the shops to get equipment etc. Really builds the full picture of your day which I think is pretty interesting. Good choice to change colour as the colour doesn’t come across the screen as real nice. Have you thought about a cherry red you know like real dark cherry almost black in some light. That could look nice !!

I'm sitting here smiling along with you guys. Happy and excited for your hard work that has paid off. Thank you for sharing

Watching elazar repair and paint every panel on the viper Ta is what got me hooked on watching goonzquad back in the day. Finally the day has come having your own super clean booth. Congratulations guys, keep up the great content 🎉

Purchase a nice weather tight shipping container. They are perfect for storing parts. You can put shelves on both side and store all kinds of stuff and get it out of your shop. Best option!

Orange and black on the urus would look sick

We are so happy for you guys, and it is so great to see all of your hard work paid off!

So awesome how pops became the star of the show. Love the family dynamic 😊

Let's go Simon and Elazar ...

the ditch witch - the booth was a good idea - design an appropriate sign for the shop - a lil fancy, a lil basic - you should get the elec inspected - proper bonding, proper ground rods, nec is variable year to year - you may want gfi plus anti arc breakers - do add walls on sides to protect motor. the place is almost perfect now - stay there for a while

Hey guys that is clean, it's the deal of the day, smart thinking.

Awesome stuff guys! I think you need to add the alignment machine 100% you would be a complete shop! Do it!! Fit nice to the main building on either side, just addon to it

I agree with previous comments. Where did you guys go? Got myself in a routine watching you guys. Now nothing?

Man I shore miss when yalls uploads were scheduled now I don't no when yall are uploading but don't blame yall are more financially stable and married now but it still sucks lol

In Sweden, it is required that you have at least 2 years of training, specifically for high current installations. Strange that as an amateur you can install high current installations in the US.

My suggestion for the Urus is a satin finish gun-metal dark grey with some fine navy flake mixed in. You know how gun bluing on a rifle barrel looks black but in the sun is has a dark blue metallic look to it. The satin finish will make the gloss black vents and skirts really stand out.

Hi Bros, Your paint shop absolutely looks great and this will change a lot for you because now you can control the whole process from changing a wrecked car into a beauty all by your own without being depending on a waiting list for a paint shop in your surrounding area. Very keen to learn what color the Lamborghini Urus will get but if I was in your position I would have stayed with the nice original white of this car. Wish you lots of success with all your ongoing projects and send you love from the Netherlands

You boys are nearly a turn key shop now! Alignment machine away!! Congrats boys!!!

I have been watching you guys on RU-vid for about 6 years now and I can't wait to see the car be fully painted and it will look good in metallic white because it will give the car the nice look in the sun and keep up the awesome work.

Black with a the lambo purple pearl and black everything else out that beast would be unreal

I would paint it factory color that way it doesn’t change from the title. Then after the paint fully cures wrap it in whatever crazy color you decide! Cheers boys! 🎉

I've been a fan of the goonzquad since day 1, and tbh i dont know what i'll do if i haven't discovered you guys.. inspirational and a blessing to witness. And just to add one observation that I made, make sure that the burying of electrical wires are within compliance with local regulations and codes... that job to me doesn't seem like a durable and desirable one, especially below where vehicles will be frequently driving. Please read this and understand guys.

Need more content

So awesome to see how far you guys have come! Always a pleasure watching your videos ❤

Nardo Grey, with the black wheels and black accents it will be awesome looking!

sheet the oven walls whilst you can, whilst its fresh and new. keeps the walls bright, white and like new! Here in the UK we also have plastic grass down on our booth floor, works amazingly to reduce trash in the paint. tricky though with a down draft.

Missing the 3 videos a week boys.

You should do a burnt orange to black colorshift paint job or some other colorshift but that would be totally outta the box and different for you guys. It would even be super epic!!

You'll be digging out that conduit/wire if anyone catches you burying it so shallow.

Even though the color was a bit off, that wrap-job was top-notch! It will be good to see the Urus get a proper paint job!

Please make sure you have videos for Sundays at least.

Looks awesome guys, when you do your maintenance on the spray booth be sure to grease your electric motors, they will last a lot longer, and check your belts for wear, cool to see you guys get your booth going, now it's time to start kicking out some wild paint jobs,.😊

Would love to see a bright flashy color for the Uris. A green or a yellow!

the cracks in the top layer of the asphalt, expanding water in winter can destroy it

Just think back a few years ago when they announced the purchase of the lot? Filled with trash, overgrown with weeds and trees. Through hard work and dedication, what they have accomplished is incredible. Whatever money they earn from YT and merch is well deserved!

Very good job on the wiring. Pops looks like he's feeling better.

I still want to see you guys take a big torque wrench and properly torque those Center Lock wheels on the Aventador, the car looks amazing but if one of those wheels decides to take off it will cause A LOT of damage, same thing goes for the 911 before you drive it.

Ain’t been a video in a week. Great job guys!

Doesn’t Power have to be 36 inches down for code? That’s basically on the surface

Vantablack - Black 3.0 would be a nice colour guys!

So not used to seeing wire so shallow. Here we have to bury wires 3ft down to get them below the frost line

The paint booth looks fantastic! Are you going to build a little room off to the side for mixing paint?

My goodness y'all live in a different world. In my neck of the woods we can't just run our own electric. It has to be a certified electrician. Most especially in a commercial structure. No matter how good the work is they won't pass it or they'll shut you down for code violations.

im so excited to see yall do some good work in there so glad yall got a paintbooth

I think a metallic red would look amazingg

U can take ur time painting... make the 1st paint job memorable.. something that looks good.. deserving of a lambo...