Тёмный

P0455 Check Engine Code - Purge and Vent Valve Replacement - Trailblazer Envoy - 4.2L Vortec 

The Daninator
Подписаться 79 тыс.
Просмотров 41 тыс.
50% 1

My Trailblazer's check engine code P0455 popped up recently. In this video I remove and replace the Purge Control Valve (Purge Solenoid) and the Vent Control Valve (Vent Solenoid) in the EVAP system. I also try to explain the cause of the code, as well as testing methods. Part number 214-2246 and CPC1007.
If you enjoyed this video, please give it a like (it helps me out!) and browse through my channel for other informative and fun videos. If I’ve earned your subscription, please subscribe and click the bell icon so you will be notified when I post new content.
I appreciate the support!
-----------------------------------------------------
OFFICIAL DANINATOR MERCH IS AVAILABLE!
Check it out:
teespring.com/stores/the-dani...
Use Coupon Code: DAN10 to save 10%!
-----------------------------------------------------
OBDII P0455 Check Engine Code EVAP System Leak Detected Purge Control Valve Vent Control Valve Solenoid removal replacement test methods
For business inquiries, please contact The Daninator at:
the_daninator@hotmail.com
Instagram: @the_daninator_yt
Disclaimer:
Due to factors beyond the control of The Daninator, I cannot guarantee against improper use or unauthorized modifications of this information. The Daninator assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. Use this information at your own risk. The Daninator recommends safe practices when working on vehicles and or with tools seen or implied in this video. Due to factors beyond the control of The Daninator, no information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. Any injury, damage, or loss that may result from improper use of these tools, equipment, or from the information contained in this video is the sole responsibility of the user and not The Daninator.
Romans 5:8
#diy #cars #thedaninator

Авто/Мото

Опубликовано:

 

26 апр 2023

Поделиться:

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист
Посмотреть позже
Комментарии : 32   
@eddiecard
@eddiecard 10 месяцев назад
Best vid on this repair. Thank you for posting and placing the cam exactly where we can see the parts. 🙏🏽
@victoralarcon8545
@victoralarcon8545 3 месяца назад
I like the way the video was done very clear I’m glad you didn’t show your cat and all these other dumb things that other people do you’re a professional thank you
@thrillbilly9785
@thrillbilly9785 Год назад
Love those OSHA approved crocs! Seemed like a straight forward fix. Gotta love the one's that don't fight you the whole time. My expedition has been killing me with the EGR system lately.
@cecilrhodes2618
@cecilrhodes2618 8 месяцев назад
Great video! Critical info! Thanks so much! I'm about to do the same thing on a Trailblazer I'm working on.
@voidisyinyangvoidisyinyang885
@voidisyinyangvoidisyinyang885 3 месяца назад
I triggered the EVAP code after I did my undercoating with 4 lbs of pure gum turpentine and 4 lbs of wax. hahahaha. I probably covered up the vent valve - after I cleared the code it didn't come back. I'll take a look again. thanks for the vid - too bad my FailBlazer t-shirt got worn out so fast!! I'm at 292,000.
@31spring
@31spring 9 месяцев назад
Thank you for sharing
@jhuntosgarage
@jhuntosgarage Год назад
I have learned. Thanks for sharing!
@TheDaninator
@TheDaninator Год назад
Thanks JHunto!
@sunshinetx36
@sunshinetx36 Месяц назад
How long did repair take to do? Thanks
@JasonD-xc9ju
@JasonD-xc9ju 3 месяца назад
Awesome brotha thank you
@robertdellaria8067
@robertdellaria8067 2 месяца назад
Appreciate it
@2000jackben
@2000jackben 8 месяцев назад
You can test the purge valve to see if it is stuck open or not. Remove the 10mm bolt holding the purge valve bracket to the engine block. Then move it out for easier access to the hose clips. Remove the rear hose by squeezing the clip on both sides and sliding the hose off. Start your motor and put your finger over the rear hose inlet you just removed. If it is trying to suck your finger into the valve it's stuck open and needs to be replaced. If there's no suction, then it's still good and you can reassemble it. Then you can move on to check for the vent valve being stuck or something else leaking. If your fuel filler tube is badly rusted. It might have air leaks at the any of the connections or through any of the rust deposits. Rule out one thing at a time for leaks. And if you run out of patience get hammered and come back to it the next day 😂
@FabianTrahan
@FabianTrahan 10 месяцев назад
Thanks
@daisy5644
@daisy5644 6 месяцев назад
I was told if the vent solenoid was bad, it makes it tough to pump fuel in.
@gflackoescobarofficial5921
@gflackoescobarofficial5921 3 месяца назад
Did you have gas smell before fixing ?
@fawnlliebowitz1772
@fawnlliebowitz1772 Год назад
Out of the two which is the most likely culprit? I disconnected the battery, didn't help. Gas mileage is 20 which I'm happy with. Code says it's evap system, Envoy runs like a clock 140K miles. So far I'm ignoring it.
@Right-2-Bear-Arms
@Right-2-Bear-Arms Год назад
I did this repair a month ago the check engine light was gone for a solid month until today. So I have no idea what the problem could be now 😊
@michaelmedeiros1587
@michaelmedeiros1587 Год назад
Process of elimination my friend. It could be your fuel pressure sensor that's bad and throwing of a faulty code
@sunshinetx36
@sunshinetx36 Месяц назад
How long did repair take? 30 min 60 min? Thanks
@user-vs9ob5kr6f
@user-vs9ob5kr6f Год назад
If your hand is blocking I cannot undo vacuum lines I need to see how it disconnect them
@2000jackben
@2000jackben 9 месяцев назад
It's much easier if you disconnect the bracket first. There's just one 10mm bolt holding the entire assembly to the engine block. Then you can move everything out for a better view of the connectors on the purge valve. And get your hand in easier.
@juniorramirez1073
@juniorramirez1073 Год назад
Is it necessary to change both Parts as you did? Or can I only change the purge valve?
@1jeffr
@1jeffr 8 месяцев назад
Yeah, if you are going to shotgun parts, I would replace them one at a time. The purge valve first, and if that didn't fix it, then the other.
@STC877
@STC877 5 месяцев назад
Both are part of the same code
@maxpajak3691
@maxpajak3691 Год назад
For anyone wondering how to properly get the coupling closest to the front of the cehicle off there is a push clip on the backside of the coupler. Push in the solenoid and push up on the little plastic piece. It comes right off
@2000jackben
@2000jackben 9 месяцев назад
You are correct. but I could hardly see the purge valve or get my hand in. So the first thing I did was to take the bracket off and move purge valve out. Then I could see all the couplings and the clips and disconnect them easily. 6:18
@wild8757
@wild8757 5 месяцев назад
Wish you had shown where the charcoal canister was
@JustThatCoolGamer
@JustThatCoolGamer 9 месяцев назад
Did he say Chevy FailBlazer? 😅😂
@edwinprieto9428
@edwinprieto9428 6 месяцев назад
Check engine light 07 gmc envoy
@bucephalus14
@bucephalus14 Год назад
Chevy Failblazer 😂
@gflackoescobarofficial5921
@gflackoescobarofficial5921 3 месяца назад
Did I hear Chevy fail blazer ? Lol
@MailDeliverySystem-xw6hh
@MailDeliverySystem-xw6hh Год назад
Reported for non-skit intro. 8 /
Далее
Simple Checks For P0455 Evap Large Leak
12:16
Просмотров 112 тыс.
GT-R - ВСЁ! :(
57:36
Просмотров 414 тыс.
Common Chevrolet TrailBlazer GMC Envoy Problems
19:47
2006 Chevy Trailblazer Evap Vent canister/solenoid
8:21
P0455 EVAP CANISTER VENT VALVE 2005 TRAILBLAZER
10:47
2004 trailblazer evap stuff.
4:32
Просмотров 72 тыс.
Её машина неуправляемая
1:00
Просмотров 1,2 млн