Panhard Bracket × 4BT Cummins Discovery #41 [Land Rover Build]

Подписаться 46 тыс.

Просмотров 517 тыс.

50% 1

Fabricating a custom bracket from tube, for attaching the panhard-bar that locates my front axle under the Rover, but clear from the swing of the pitman-arm on the newly mounted Land Cruiser FJ80 steering gearbox.
~ PART#41 in a project dubbed "Nanuuq" to swap out my lifted Land Rover Discovery 2's blown 4.0L V8 & boring ZF auto for a Cummins 4BT 3.9L turbo (Holset Super HX30W) diesel 4-cylinder engine (Bosch P7100 pump) with an NV4500 5-speed manual transmission. The AWD 4x4 will remain with the LT230 transfer case divorced behind it all, & plenty of Dodge 6BT parts too. Another big phase of my custom DIY build to create a do-just-about-anything off-road / overland rig. Did I mention it's a camper too?
~ BUILD THREAD: (Entire build) www.overlandbound.com/forums/...
~ BUILD THREAD: (4BT specific) www.4btswaps.com/threads/100657/
~ DISCLAIMER: Please do not do/repeat/imitate/recreate anything I do in my videos. JUST DON'T! It can be very harmful to bystanders, your person, your wallet, & your psyche. Don't risk the only "meat vehicle" you get!

Авто/Мото

Опубликовано:

9 янв 2020

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 237

@malcolmyoung7866 4 года назад

Some serious talent there. Re affirms my decision to do ‘economics/geography/art’ at school, instead of ‘tech drawing/metalwork/woodwork‘ was a bad one. Luckily this format that is RU-vid has a few individuals to inspire my desire to learn these skills and more than a few tips at an older age. Keep up the great work. Many thanks.

@Tinker1837 4 года назад

Hey thanks! Same here, would've had such a big head start if I would've aimed more towards working with my hands instead of computers... but ah well, got there eventually 🔧

@gafrers 4 года назад

Wonderful as always both in the build and the editing. The idea of You with a Milling machine is scary 😁 endless possibilities and brackets

@Tinker1837 4 года назад

Mill + Lathe + TIG = overbuild & swap all the things!

@TheCanadianBubba 4 года назад

It is hard not to feel like a total hack after watching your work come together... thank you for setting such a great example. Hope it is a great 2020 for us all.

@Tinker1837 4 года назад

I'm pumped for 2020!

@LvdMade 4 года назад

🙅🏽‍♂️ looks good!! And finally a new episode!!

@Tinker1837 4 года назад

About time haha!

@Bread996 4 года назад

Tubular! I hope those washers hold up though. They are a bit thin and may wallow out. But of course you can just beef it up later if it does 👍🏻

@Tinker1837 4 года назад

Those washers are the same thickness as the old bracket where that bolt went thru... so I hope so too 🤞

@Bread996 4 года назад

@@Tinker1837 Cool. They looked like thin fender washers on the video. Should be good to go then!

@Tinker1837 4 года назад

@@Bread996 They're not the higher grade steel like that DOM tubing, so there's still a possibility of the holes getting out of round, but definitely something I'll have to keep an eye on.

@jasonvenegas8264 4 года назад

Another update awesome

@Tinker1837 4 года назад

Next step is fairly easy (and shiny!) so it should be in video pretty quick.

@jasonvenegas8264 4 года назад

@@Tinker1837 great !! I will stay tune

@justinelliott293 4 года назад

That coping tool was genius..

@Tinker1837 4 года назад

Glad I took a break to make it... saves so much time!

@amusinghp8843 4 года назад

Finally ! :) New series :)

@Tinker1837 4 года назад

I'm slow haha

@CaptainBuilt 4 года назад

Nice new bumper.

@Tinker1837 4 года назад

That's from "Tactical Rovers" and it's tough! Taken some big hits, including a crazy person in a newer Subaru that ended up totaled while I just had scuffed powdercoat.

@defenda2477 4 года назад

Quality project mate !! Discovery’s are such awesome 4wds, good to see one getting the love they deserve.

@Tinker1837 4 года назад

Doing what I can to keep at least this one out of the scrapyard!

@markmorton2801 4 года назад

That is an awesome project. I did a complete GM running gear in my rover. 5.3 6l80e 241tcase and dana axles. I had to change the location of my pan hard bar and I did a high steer setup. I had some bump steer so now at ride height pan hard bar and drag link are flat it helped a lot and it is stronger since I used all 1 ton stuff.

@Tinker1837 4 года назад

Sounds badass! I'm excited to build a set of axles & long travel suspension for mine. I'm all about spherical joints & tubing setups these days, & 1 tons like your setup would be mint.

@timb4655 4 года назад

Genius. Damm you with your killer fabrication and creative cinematography skillz 😎

@Tinker1837 4 года назад

I try! It's weird how the process of recording it all seems to make me want to try new things or get more creative with both building & filming.

@nothsim 4 года назад

Cold pizza for a hangover. Warm Pizza is a snack

@Tinker1837 4 года назад

Haha well said.

@hamdankreem98 4 года назад

One of the best channels ever.. Just be faster posting these videos

@Tinker1837 4 года назад

I'm so slow! Definitely something I hope to improve in 2020.

@persistentwind 4 года назад

I was worried about lateral loading where the 2 supports connect to the plate until I saw the gussets er whatever you call the fillers... literally breathed a sigh of relief. Looks great!

@Tinker1837 4 года назад

I had thought of maybe adding another tube or 2 to brace the loads in the direction of the bar, instead of just gussets, but it ended up looking way overkill.

@Reaper4367 4 года назад

Effective, functional, Beautiful!

@Tinker1837 4 года назад

Turned out not half bad :D

@jimmyjazz1186 4 года назад

Excellent work bro.excellent👍👍👍

@Tinker1837 4 года назад

Thanks!

@Naizi25 4 года назад

Хорошо получилось, молодец.

@Tinker1837 4 года назад

I'm very happy with the way it came together!

@francfzx1 3 года назад

CONGRATULATIONS !!!!!!!

@Tinker1837 3 года назад

Thanks :)

@Yura.Rulit. 4 года назад

Выглядит очень красиво! 👍

@Tinker1837 4 года назад

Thanks!

@johnsmith-jy2uv 4 года назад

Hi man, just found your channel and thoroughly enjoying your videos! Keep up making interesting content like this!

@Tinker1837 4 года назад

Will do! 👍

@user-nw5xv5ib3l 4 года назад

Жаль незнаю языка а то по общались бы , моё уважение за труды , хорошая работа .

@Tinker1837 4 года назад

It's okay, language is difficult! And thank you!

@jth1987leb 4 года назад

Looks great man!!!

@Tinker1837 4 года назад

Thanks! It turned out better than I had expected haha

@iongratianserban6937 4 года назад

You are so skilled man, I am so impressed with your work! You're a master.

@Tinker1837 4 года назад

Thanks! I'm no master yet, but I keep trying to learn more as I go through these projects.

@gecar4x414 4 года назад

Nice work

@Tinker1837 4 года назад

Thanks!

@diego.barisone 4 года назад

great job!

@Tinker1837 4 года назад

Hey thanks!

@flodel7790 4 года назад

genial vivement la suite

@Tinker1837 4 года назад

More soon!

@mrAudisubaru 4 года назад

i would love to have the skills to weld with a mig or even with tig that is so usefull maybe i will learn it one day.

@Tinker1837 4 года назад

I'm decent with MIG but super hooked on TIG now that I've had a few tries with it! I found a relatively inexpensive entry level option from Eastwood (called TIG200) that doesn't cost $2,000 but can still do both steels + aluminum, unlike many chinesium units.

@mrAudisubaru 4 года назад

@@Tinker1837 Yeah i must try something like this soon and see how it goes.

@silarik 4 года назад

Only two channels I have seen that much clean work other Chanel is goonz squad

@Tinker1837 4 года назад

Thanks for the kind words & I'll definitely have to check them out too!

@silarik 4 года назад

They are not smart as you guys stay blessed you record it's feel like we are working with you. Enjoying too much thanks for everything

@migdad96 4 года назад

Hello 👋 Tinker We have been waiting long time for this episode finally, but is really look so good and please tell us when you will post the next episode 💪💪

@Tinker1837 4 года назад

Next thing I need to work on (power steering fluid reservoir) should not take too long, & glad you like :)

@johnfenn 4 года назад

Thank you for not talking, or playing music.And starting out by saying "Whats up guys?"

@Tinker1837 4 года назад

You are welcome, much prefer to keep it simple & straight to the point for the most part.

@thedesigner5771 4 года назад

Awesome

@Tinker1837 4 года назад

Turned out better than I expected!

@QuantumAlchemyst 4 года назад

Nice job man. Like the entire project you are doing an excellent work. 👍🏻👏🏻👏🏻👏🏻👏🏻😃

@Tinker1837 4 года назад

Thanks, it's a fun one for sure!

@chrisseger6870 4 года назад

Oh man. I love your videos and I can't wait till you get this on the road. You are one smart and talented sumb!tch. Love how you make sure to fix whatever needs to be in order to do it right. Keep it up!

@Tinker1837 4 года назад

Getting close now! It makes it so much easier (and enjoyable) once I realized it didn't need to be a panic rush. Future me will be happy I took the time to do it right 👍

@steveanderson3942 4 года назад

Nice work young man 👍😎

@Tinker1837 4 года назад

Thanks!

4 года назад

Nice 👌👍👏

@Tinker1837 4 года назад

Thanks :)

@kayorenan406 4 года назад

Top !!! Curte a ferramenta que vc fez a respeito ao corte do tubo. Muito legal...

@Tinker1837 4 года назад

It works great and so inexpensive!

@user-jr8mh7pv1z 4 года назад

ما شاءالله عملك ممتاز بالتوفيق يا حبيبنا 👍👍💜💜

@Tinker1837 4 года назад

Thanks!

@franckesteoulle7608 4 года назад

Urrghhhh! Poor Landy...

@Tinker1837 4 года назад

"Gentlemen, we can rebuild him. We have the technology."

@Yotubet 4 года назад

En la fijación al chasis tenías que haber echo agujero en en la chapa para soldar internamente

@Tinker1837 4 года назад

No, I did not have to do that thankfully.

@dubfalcon4489 4 года назад

Kickin ass takin names. How much longer till ur rollin coal tink!!!

@Tinker1837 4 года назад

Spring time is the goal to be fully road ready, gonna be awesome!

@seniorxj2931 4 года назад

Simply WoW! I would definitely pay you to work on my jeep for sure! Very nice work indeed!!

@Tinker1837 4 года назад

Glad you like!

@seniorxj2931 4 года назад

@@Tinker1837, where do you reside?

@Tinker1837 4 года назад

@@seniorxj2931 Michigan

@seniorxj2931 4 года назад

@@Tinker1837 kinda far from Virginia.

@Tinker1837 4 года назад

@@seniorxj2931 Ya, but I bet there's some proper 4wheeling spots out that way.

@MultiCoffeetogo 4 года назад

Wie geil. 😉😂

@Tinker1837 4 года назад

😎

@dartmoordave 4 года назад

You do nice work in a well-equiped shop but have a tidy up, mate. Tidy shop is a safe shop.

@Tinker1837 4 года назад

Thanks, but not my shop & much of the clutter is of the antique variety so I have to take care moving things.

@dartmoordave 4 года назад

@@Tinker1837 I know how that is mate, lucky to have access to a shop.

@Tinker1837 4 года назад

@@dartmoordave Very thankful for it, that's for sure!

@NathanNostaw 4 года назад

I really like the look of this bracket, but is it going to be up to the high loads and impacts from off roading?

@Tinker1837 4 года назад

I'm confident it will, but only one way to find out... and that's finally driving it out of the shop and getting on the trails again!

@anomamos9095 4 года назад

This may be a dumb question but! Would it not have been easier and better to swap the bar around so the frame mount is on the passenger side? It was designed as a right hand drive vehicle so making it left had drive was a bodge to start with.

@Tinker1837 4 года назад

I looked into that, but sadly my axle doesn't have the brackets on the axle for the right hand drive bar... weird considering how many other things it has that are RHD bits. I figured it easier to weld things into the frame then the axle tube, plus I think that the steering & panhard bars have to swing from the same side to prevent binding & scary bump-steer effects.

@scarface-39 4 года назад

Very nice!!!👍

@Tinker1837 4 года назад

Took a fair bit of pondering, but turned out pretty good I think 😎

@scarface-39 4 года назад

Tinker absolutely!!

@Vladimir-pl3qk 4 года назад

I really liked the technology of copying the pipe profile...(I'll take it on Board : -) and you are not in instagram by chance...

@Tinker1837 4 года назад

I was happy with that DIY tool worked, feel free to use the idea!

@volodymyrnekhoda7017 4 года назад

If you make a couple of hundred improvements, the Bentley will surely turn out of the Land Rover

@Tinker1837 4 года назад

Hahaha! Oh man that got me 😆

@user-bc4lv4lq1y 4 года назад

Маладес 👍👍👍

@Tinker1837 4 года назад

Thanks!

@user-lo3yz4vl5u 4 года назад

🚜💭🛠️👍

@Tinker1837 4 года назад

Glad you like :)

@dc46522 3 года назад

From what land cruiser did you get the steering box. Heck of an idea.

@Tinker1837 3 года назад

FZJ60 was the donor, thanks!

@yuryd. 4 года назад

I hope it will work, becouse in some countrys illegal to weld any thing to the frame becouse after welding metal gonna be much softer and can crack, any way I like your customizing

@Tinker1837 4 года назад

Thankfully the rules in my state are not excessive with things like this!

@yuryd. 4 года назад

@@Tinker1837 I know about australia

@Tinker1837 4 года назад

Australia is very picky with those! So are out states here with the bigger cities (California, New York, etc)

@dartmoordave 4 года назад

Knowing how thin Disco chassis' are your bracket is much stronger than the frame. Check it often?

@Tinker1837 4 года назад

I had not heard they were considered thin, news to me! I was actually a bit impressed with the chassis as I worked with it, since it's as large & thick as most any truck up into the 3/4-ton rating that I've encountered. And fully boxed too, where many are c-channel, but then that's the classic debate of stiffness versus flexibility. A full tube frame build would be the dream, but a long way off yet. This build will likely never "end" 😎

@dartmoordave 4 года назад

@@Tinker1837 Corrosion is the devil of Disco's. Favourite areas are outrigger chassis brackets, rear body floor/inner wheel arches/rear body on 4 doors around door sills. If its got a towbar make sure the attachment points are sound, major chassis rusting at rear chassis legs and x member, its not unknown for the whole rear x member and towbar to tear away. Soak the box chassis in old engine oil regularly, the original engine would do it for you. Be aware the centre diff planet gears are fragile and along with the halfshafts, don't like being shock loaded climbing rocks, snatching stuck vehicles etc. Treat it kindly and you'll be OK.

@Tinker1837 4 года назад

@@dartmoordave Good to know! My chassis was very nice but is getting in need of restoration thanks to Michigan's extreme use of salt thru our half-year long winters. I'll make sure & give those points a careful eye when I start the frame clean-up come spring time 👍

@dartmoordave 4 года назад

@@Tinker1837 Didn't want to frighten you but here in the UK my '94 Trooper with C section chassis has no body rust at all and surface rust on the chassis but you won't ever find a '94 Disco here either; still running or not rotten. Even if the engine is doing its best to lube the chassis! Keep washing the mud traps.

@morefunny7893 4 года назад

👍🏻👍🏻👍🏻👍🏻👍🏻👍🏻👍🏻👍🏻

@Tinker1837 4 года назад

Glad you like :)

@autobodyrepairclearcoot4146 4 года назад

Wuts up tinker Im waiting for your First test drive for so long plz dont make us wait

@Tinker1837 4 года назад

Very soon! Working on video edits now :)

@JordanVH98 4 года назад

Where can I get one of those magic TIG wands?!

@Tinker1837 4 года назад

I dug her up out of a friend's empire of dirt, must be a limited edition type of thing... Ha!

@jackqb 4 года назад

did you have any starting budget before the start of the project or you just went for it?

@Tinker1837 4 года назад

I didn't, just figured in for the usual ~$5k if you do it real simple, or ~$10k if you go all out on a full powertrain swap.

@jackqb 4 года назад

@@Tinker1837 You have great skills tho.. whats your background? mechanical engineer or self taught?

@Tinker1837 4 года назад

Self taught, & thanks, I try!

@ArturKyrgyzstan 4 года назад

👍👍👍

@Tinker1837 4 года назад

😎

@roverman985 3 года назад

Is it gonna clear tire at full turn?

@Tinker1837 3 года назад

Yeah, first thing that the front tires can hit is actually the rearmost corners of the front bumper if you can believe it... weird, but I'll trim that up before the first trail run.

@michiganmudlife1789 4 года назад

What city are you located near?, I’m located near Ludington I just discovered your channel I think what your doing is pretty sweet

@Tinker1837 4 года назад

Grand Rapids, but north is my heading for good times about 90% of the time 👍

@matts490 4 года назад

Really like your work on that bracket but would all that load be basically transferred through the 2 small washers that are only tacked in place? Good to see more progress 👍🏼

@Tinker1837 4 года назад

Those washers are actually pretty big (2" across & 1/8" thick) and same thickness as the old bracket, also they are fully welded around (with TIG)

@mightymikee 4 года назад

Amazing welding skills! Would you consider boxing the bracket for added strength? And little brace to give little more lateral support left to right? Just my opinion but I feel that track bar bracket is putting a lot of torque on the welded joint at the frame.

@michaelhite1433 4 года назад

Did you change the front springs to handle the weight of the 4BT? I was wondering because I was planning on using a 1.9 tdi in my D1, but I’ve found a 4bd1t Isuzu with only 52k on it for dirt cheap. It is very similar to the 4BT in most specs except it isn’t as tall.

@Tinker1837 4 года назад

I did not yet, but will for sure after I get it in a scale, that way I can calculate the spring rate to restore it back to the lift height before all this work.

@lukaverhozin4627 4 года назад

Я смотрю кто то даже за твой труд дизлайки ставит( не обращай внимания это не люди )))))

@Tinker1837 4 года назад

I am not sure I understand, translator is being funny :(

@lukaverhozin4627 4 года назад

Tinker , я имею ввиду что ты человек с золотыми руками и видео монтируешь очень интересно, а некоторые люди которые тебя смотрят не понимают что ты молодец и ставят дизлайк:(

@busman2000 4 года назад

Do you have footage of the modified Discovery being driven..? Oh do you have to get an engineers certification on all your modifications prior to on road use?

@Tinker1837 4 года назад

Not yet with the 4BT installed but lots from before the V8 had issues here in this playlist (down near the bottom of the playlist there are some trips I recorded) ru-vid.com/group/PL0fo2S6vPzlHRu8oH5bXgUFSGmPkvubag And thankfully I don't need any certification for putting the 4BT Rover back on the road, at least in this state in the USA 👍

@NicolaLiotti 4 года назад

Hey big brooo... where did you finish?? I'm waiting like all last episodes. Quarantine is killing me, I need to entertain myself with someting really good (like your videos) :( :( :(

@Tinker1837 4 года назад

Editing the next video right now actually :)

@zulkiflyhjali5142 3 года назад

🤗💪🤗

@Tinker1837 3 года назад

💪😎👍

@dubCanuck1 4 года назад

How does the tire clear at full lock?

@Tinker1837 4 года назад

It's been a tight fit ever since I lifted it 4" and installed the 35" tires... going to need a little trimming before it gets 37" or 39" tires 😎

@dubCanuck1 4 года назад

@@Tinker1837 sweet!

@user-nl2ed7wt1m 4 года назад

молодец , сварные швы не забудь покрасить

@Tinker1837 4 года назад

Thanks and yes but I must wait for it to be warmer (no heat in my building)

@sudirman7670 3 года назад

funny mechanic

@Tinker1837 3 года назад

Thanks :P

@florinnistor7767 4 года назад

Where did you get all those parts for your Discovery ? I also have one and I need parts

@Tinker1837 4 года назад

Lots & lots of sources! For used parts Ebay is fantastic for finding deals, for OE replacement parts I like Atlantic British, for bolt-on upgrade parts Lucky8 is great, for fabrication parts I like Ballistic Fabrication, & for just about any racing/performance parts Summit Racing is my favorite.

@TheRebelOne. 4 года назад

2 questions. 1.Was this a factory modification as you did show a cad drawing mid video or did you come up with the drawings yourself? 2. Will you be fabricating a sump guard to protect the underside oil pan of your beautifull 4BT? Nice work. Thankyou!

@Tinker1837 4 года назад

1) That was a drawing I came up with, actually the 3rd version of it by the time I did the filming, but ended up very near true to life from it. 2) Yes, for sure! I've often thought of a dry-sump system for it, but due to complexity that will have to wait for a later phase of the project when I dive deeper into the engine build.

@TheRebelOne. 4 года назад

@@Tinker1837 Appreciate your reply. Thankyou. 👍

@gaboonviper85 4 года назад

Any updates????? Hope you're safe and not too effected by this crazy virus stuff! I finally got a diesel vehicle..... been busy getting mods and maintenance done on it..... you feel like making an exhaust system for a bmw? Lol

@Tinker1837 4 года назад

Yessir! Funny timing too because I just uploaded the next one! I'm off work, so have more Rover time which is nice, but staying safe so far. Hey maybe because I'll have a TIG welder here shortly :D

@gaboonviper85 4 года назад

@@Tinker1837 well it's a bmw 335d and just finished deletes and next weekend taking it to new to get tuned...... wouldnt mind a road trip to see your rig in person and toss you some caaaaash to fab up a straight pipe!

@gaboonviper85 4 года назад

@@Tinker1837 add me on Facebook or whatever if you think it would be something youd be interested in doing:-)

@Tinker1837 4 года назад

Twin turbo straight six, nice! I'm so excited to have the fine control & clean results from TIG. I need to upgrade the exhaust on my rally car, so I think that'll be my first TIG welding victim. But yeah we'll see how I do with it if I can fab some things for people anytime soon. Thankfully I have a friend who's quite good at it that I can bother for tips/tricks.

@gaboonviper85 4 года назад

@@Tinker1837 hell I dont need anything fancy.....just not the best welder lol. But only a few people make exhaust for this car and they really bend you over for it.

@valenting4928 4 года назад

Maybe you can make a spacer to another frame?

@Tinker1837 4 года назад

Not sure I understand...

@valenting4928 4 года назад

@@Tinker1837 a.d-cd.net/d954434s-960.jpg

@Tinker1837 4 года назад

Oooo that is interesting!

@renatovazpinto9023 4 года назад

🙃

@Tinker1837 4 года назад

😁

@lukaverhozin4627 4 года назад

Красава

@yuryd. 4 года назад

это он не смог перевести....

@Tinker1837 4 года назад

Means beautiful...? (czech?)

@lukaverhozin4627 4 года назад

Tinker я из России , точнее Удмуртия , Родина Калашникова)))

@lukaverhozin4627 4 года назад

Редко ролики выпускаешь(((

@Tinker1837 4 года назад

Oh sorry I thought maybe that Czech is what the first word was from. I own one! Beautiful rifles :D

@user-sl8fd5gv1y 4 года назад

пиццу снизу надо греть

@Tinker1837 4 года назад

Hmm yes you have a good point, better for crisp crust 👍

@cotyluckett 4 года назад

Oktoberfest.... isn’t that in Cincinnati ?

@Tinker1837 4 года назад

That hoody came from a fun event in Grand Rapids that was in John Ball park, but outgrew it & is now held at Riverside park (if you're in the area & interested). But aside from the huge one in Munich, from my understanding the big ones in the USA are there in Cincinnati & a close second in size out in La Crosse WI.

@jimmyjazz1186 4 года назад

WKRP is 😂😂😂😂

@jimmyjazz1186 4 года назад

Das weiss ich leider nicht Kumpel.I live in Mannheim.Here it's been cancelled because of corona virus this year

@Tinker1837 4 года назад

That is sad :(

@Aufalcon69 4 года назад

Where did you get the bullbar from

@Tinker1837 4 года назад

That's from "Tactical Rovers" and it's tough! Taken some big hits, including a crazy person in a newer Subaru that ended up with a totaled car while I just had scuffed powdercoat.

@Aufalcon69 4 года назад

Cheers mate I might have to get one for my disco haha

@marcobarbe 4 года назад

When a video to the car un action?

@Tinker1837 4 года назад

Soon! Before spring, going to be a cold test drive haha!

@timskiy_85 4 года назад

U need a grinder!

@Tinker1837 4 года назад

What kind, like smaller hand-held / die grinder?

@timskiy_85 4 года назад

@@Tinker1837 нет, инструмент для подготовки труб к сварке под полукруг разного диаметра. возможно так будет легче)

@shabanhelal 4 года назад

probably will suffer bump steering

@Tinker1837 4 года назад

No, no issues. It had very nearly the same setup for several years with no "bump steer" issues.

@henryramonaguilarcarmona3324 4 года назад

Hi bro .. I like to work whith You..

@Tinker1837 4 года назад

Wrenching with friends is always more fun :)

@GioGioGuaro 4 года назад

I would like to work with you even if I have to pay you jjjj

@Tinker1837 4 года назад

You wouldn't need to do that :P

@user-bw2kd6gf6l 4 года назад

Как то вызывает сомнения

@Tinker1837 4 года назад

No need to worry :)

@DJInclined 4 года назад

See that red rat wagon again

@Tinker1837 4 года назад

It's in need of upgrades, but still running strong 💪

@user-bw2kd6gf6l 4 года назад

Рычаг получается большой, плюс рама была нагрета сваркой, соответственно ослабленна и её будет рвать

@Tinker1837 4 года назад

Leverage is exact same as original. Welding frame is fine, only a risk with big commercial / industrial trucks. Will be okay :)

@user-nl2ed7wt1m 4 года назад

не ссы в трусы раму и так на заводе варят чет не рвет ни чего у меня на патрике кронштейны пружин передних вареные и нифига ездят так варили проводом а не полуавтоматом

@sludo56 4 года назад

You will ebentually nurn up your car wring not using a double ground strap.

@Tinker1837 4 года назад

Wha? Everything has 2 giant grounding cables.

@sludo56 4 года назад

@@Tinker1837 Need one more individual ground. Eventually your gfound will arv and loose ground and will find vehicles ground and fry your vehicles wiring. Just a FYI

@Tinker1837 4 года назад

I have 2 cables to frame, 2 more to engine, & 2 more to body... did I miss a spot? I agree though, very important. I hope I didn't miss something too obvious, because I want my electrics to be well sorted on this build.