Custom Gauges × 4BT Cummins Discovery #48 [Land Rover Build]

Подписаться 46 тыс.

Просмотров 64 тыс.

50% 1

Building a custom gauge cluster to hold all my new gauges in the original Land Rover dashboard surround. Here are the gauges used: www.vdo-gauges.com/instrument...
~ TIMESTAMPS:
0:00 Out Of Fuel
0:43 CAD Template
0:43 Finding Material
1:18 Cutting
1:52 Drilling
3:05 Test Fitting
3:44 Gauges
4:50 Painting
5:32 Cluster Done
6:09 EGT Sensor
7:30 Boost Sensor
7:51 Gauge Wires
8:56 Gauge Test
9:38 Outro
~ PART#48 in a project dubbed "Nanuuq" to swap out my lifted Land Rover Discovery 2's blown 4.0L V8 & boring ZF auto for a Cummins 4BT 3.9L turbo (Holset Super HX30W) diesel 4-cylinder engine (Bosch P7100 pump) with an NV4500 5-speed manual transmission. The AWD 4x4 will remain with the LT230 transfer case divorced behind it all, & plenty of Dodge 6BT parts too. Another big phase of my custom DIY build to create a do-just-about-anything off-road / overland rig. Did I mention it's a camper too?
~ BUILD THREAD: (Entire build) www.overlandbound.com/threads...
~ BUILD THREAD: (4BT specific) www.4btswaps.com/threads/100657/
~ DISCLAIMER: Please do not do/repeat/imitate/recreate anything I do in my videos. JUST DON'T! It can be very harmful to bystanders, your person, your wallet, & your psyche. Don't risk the only "meat vehicle" you get!

Авто/Мото

Опубликовано:

12 июл 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 141

@Tinker1837 3 года назад

Almost looks like a road worthy vehicle now! But my tachometer wiring still needs tweaking, since I'm trying to steal an output signal from the old Rover alternator for my RPM reading. (I have a laser RPM detector now, just to be sure the reading is accurate once it's working) Next up is a road test to verify the speedometer, boost gauge, temp gauge, and exhaust gas temps... which if all good means I can turn up the boost and start tuning it!

@jamescunliffe9872 3 года назад

As an experiment I think it's worth trying a longer exhaust to spin the turbo faster,as I see it the exhaust gas is exiting without producing enough flow to build a rise? Counter intuitive but you may also gain from having the end section actually having a slight narrowing taper!

@jamescunliffe9872 3 года назад

Engine tan coloured whole vehicle:)

@uhmlmfao 3 года назад

Still the coolest project on RU-vid. Glad to see you’re back!

@Tinker1837 3 года назад

Glad to be back! Working on the videos is a good motivator to get things done faster.

@uhmlmfao 3 года назад

@@Tinker1837 that’s a definite. Look forward to the continued progress!

@Tinker1837 3 года назад

@Harold Finch The very fate of the world could depend on the wiper's rotation....

@chrisseger6870 3 года назад

Dude. Just gotta say. You're one helluva builder. This is the most BA build. And I hope I get to see it in person at shows or an off road park or something. Frikkin cool rig. Nice job.

@Tinker1837 3 года назад

Hey thanks man! I have no shortage of people to share it with when it's more complete that have helped & motivated me thru the project.

@ggj666 3 года назад

Very nice, my poor old series 3 1980 SWB has sat on the drive with one door off waiting for me to fix it for the last 2 years. and now i have to clear off the layer of moss as well. :o)

@Tinker1837 3 года назад

The time really flies by on big projects!

@MbanziSD 3 года назад

"NO MY TRUCK IS DONE YET" @ 0:22, that is awesome!

@Tinker1837 3 года назад

Good spot haha!

@percula8 3 года назад

I retro'd my Defender with the exact same gauges and had the same problem with the RPM gauge. Once you wire your signal from the alt, there are tiny microswitches on the back to set the gauge to different pulse rates from the alt. I played around with the settings until I got it right.

@Tinker1837 3 года назад

Ah good to know, figured it would just take a few settings here 'n there until I got it right. And I'm confident I can get it near enough to exact since I have a handheld laser/photo tachometer meter to double check.

@joekirklin 3 года назад

I love seeing this thing evolve. Great job as usual

@Tinker1837 3 года назад

It's come a long way!

@gafrers 3 года назад

Great to see more progress and "cleanup"

@Tinker1837 3 года назад

In the moment these things so seem insignificant, but after I take a step back they definitely are bigger than I expect.

@seoirsemcadam7558 3 года назад

Well done mate

@Tinker1837 3 года назад

Thanks!

@eyeswideopen7450 3 года назад

Driving with gloves? Time to put a heater in that thing! Keep up the work!

@Tinker1837 3 года назад

Now I can with a dashboard :D

@NeoCole500 3 года назад

I'm so glad you're back!!!

@Tinker1837 3 года назад

Same! Getting these videos out helps push me to get things done on time.

@Adbeel1200gs 3 года назад

Increíble proceso te sigo desde el día uno y es asombroso el cariño con el que le diste nueva vida a este Discovery

@Tinker1837 3 года назад

Thanks and much more to come!

@user-un1sh8xh5v 2 года назад

Hey now that’s looking pretty fresh

@Tinker1837 2 года назад

Honestly turned out much better than I expected!

@ga1526 3 года назад

Отличная работа! Молодец.

@Tinker1837 3 года назад

Thanks :D

@Reaper4367 3 года назад

what a crackin unit! Shame there was no dip stick for the fuel tank lol. Getting closer every day mate. Cheers for the effort and sharing.

@Tinker1837 3 года назад

Thanks! Oh that one was all on me. What a dummy to not just keep it topped up always haha!

@oxygen2h148 3 года назад

Good job. 🤙

@Tinker1837 3 года назад

Thanks! :)

@josuesamuel497 3 года назад

Thanks for the ideas 😀

@Tinker1837 3 года назад

Happy to help!

@josuesamuel497 3 года назад

@@Tinker1837 liltle question, are you making the electric harness or order a prebuilt one?

@Tinker1837 3 года назад

@@josuesamuel497 Making everything custom myself :D

@josuesamuel497 3 года назад

@@Tinker1837 :0 well, that will actually help me, i had problems trying to find a harness for a toyota hilux 1987 2L, but with the ideas you give me, am gonna try make it myself.

@talalalhoyani4765 3 года назад

Keep up the good work

@Tinker1837 3 года назад

Absolutely!

@vr6prodigy 3 года назад

I am super glad to see this dash set up! Fucking awesome man! I wish I could be a part of this haha you're making art. I'm not even a diesel guy but you've basically done the impossible. A reliable rover hahaha.

@Tinker1837 3 года назад

Me too, turned out way better than I expected! Well lot's not get too ahead of ourselves just yet lol!

@vr6prodigy 3 года назад

@@Tinker1837 yeah it looks mint. And I dunno. The clips of it running and driving even with running out of fuel still sounded good and healthy.

@frank8534 3 года назад

So dang cool man. Good thing the factory installed smoke didn’t come out.

@Tinker1837 3 года назад

Those pesky angry pixies always looking for a way out!

@Serhii-23 3 года назад

Осталось дело за капотом. Good luck

@Tinker1837 3 года назад

I do not understand

@Serhii-23 3 года назад

Car bonnet

@kerrman91 3 года назад

Cool gwages

@Tinker1837 3 года назад

Thank you :)

@RonaldCiubuc 3 года назад

Soo good!

@Tinker1837 3 года назад

Glad you like :)

@RonaldCiubuc 3 года назад

I might have to do the same to my project truck I already added a aftermarket temp gauge might have to do more gauges.. check out my build on my channel

@DavisUMRacingFishing 3 года назад

Mantap ❤️❤️ need extra diesel in the vehicle

@Tinker1837 3 года назад

Yes! And now I can see how much extra haha

@megacanam 3 года назад

So wierd to see you using the Black fuel handle.... Instantly thought, "well theres your problem!" Ours are always green for Diesel.

@Tinker1837 3 года назад

The pumps here make no sense! The station across the street has all different color handles lol!

@wesm6422 3 года назад

What about all the other lights for air bags, etc. Mine has like ten different ones on start up.

@Tinker1837 3 года назад

Airbags are not there anymore & warning lights are going somewhere else

@Bread996 3 года назад

Wait you used the black pump handle?! In WA the green pump handle is diesel, the black is gas. Man I would destroy my truck if I passed through a fuel station like that :)

@Tinker1837 3 года назад

Yeah the pumps around here are goofy with no real sense behind the colors... that's why I put so many diesel only stickers all around the fill door so I remember to double check 😆

@stephenpenland278 3 года назад

I'm from Port Orchard WA. and commented the same before I saw this.lol

@95Z28A4 3 года назад

Really, really nice job on the gauges and the project overall! I followed your build on 4BTswaps. I''m pulling together components for a 3/4 ton GMT800 6BT conversion. I have planning to use the GM AD244 alternator, but am having second thoughts. I'm now considering a 28SI. What alternator did you finally end up with? And what thermostat housing did you use? Thanks.

@Tinker1837 3 года назад

Thanks! I'm using the original Rover alternator for now, but I'll likely go with a rewound diesel unit later down the road. I used the angled housing to make the custom radiator easier to fit.

@TetovoBoy 3 года назад

Idiots lights low beam high beam etc btw good work

@Tinker1837 3 года назад

I'm honestly not sure yet what I'll do for that... either drill holes in the this cluster for the warning lights + indicators, or setup a panel for those lights up on top of the cluster surround.

@sidney7931 3 года назад

Shooow

@Tinker1837 3 года назад

😎

@Dogfish47 3 года назад

That looks very neat! Are you getting speed from the transmission or from a wheel speed sensor ?

@Tinker1837 3 года назад

Thanks! The speed sensor is built into the tailshaft of the trans.

@claudioespinoza474 10 месяцев назад

Hello... excellent project... magnificent and I followed your discovery project from the beginning, I plan to do the same project of a 4bt cummins for a defender... at some point I can ask for your opinion... and idea... congratulations ..

@TheCanadianBubba 3 года назад

Great looking cluster ! Painting it the Cummins color is a nice touch. What do you think of the old racer trick of rotating the gauge so the needles are straight up at normal operating position ? might be handy if you will be doing a lot of rock crawling or high angle operation. Look forward to seeing you get it sorted !

@Tinker1837 3 года назад

Thanks, and I hadn't thought of that idea!

@TheCanadianBubba 3 года назад

I have done it, and it really stands out when something is off... great to have you back uploading, thanks for the videos !

@zachattack00 3 года назад

I was literally about to go to sleep then I got the notification

@Tinker1837 3 года назад

No time for sleep haha! >:D

@georgeaguirre8476 3 года назад

Love the gauge setup ! Where did you get those gauges at

@Tinker1837 3 года назад

They're VDO gauges from Summit Racing: www.vdo-gauges.com/instruments-displays-and-clusters/by-series/vision-black.html

@dohcdelsol93 2 года назад

Did you you ditch all the disco 2 abs/traction control components? Any issues with the immobilizer without the v8 in there? I'd like to know how you got around all the bcu related electronics.

@Tinker1837 2 года назад

I did yes, actually to clarify I ditched the ENTIRE electrical system. Went in there with bolt cutters, was surprisingly cathartic. I'm building my own bespoke system in it's place using a combination of motorsports + mil-spec + marine grade parts with breakers instead of fuses & solar etc. Big job but fun to decide where everything goes & how it works.

@dohcdelsol93 2 года назад

@@Tinker1837 I have always heard the differentials were weak on the rovers, the traction control helps spread the effort as to not grenade anything. Did you upgrade the gears and replace the differentials? Also were you able to keep the climate controls/lights/signals/power door locks/power windows functional?

@Tinker1837 2 года назад

I did not upgrade any gears, by some luck the ratio's worked out perfect with this engine/trans. They are in the range of 1/2-ton american axles, so not weak really, more the issue is cost in upgrades versus american axles like Dana60/Ford9 etc. Lights and signals I have rewired so they work, and no climate control will be custom as well.

@dohcdelsol93 2 года назад

@@Tinker1837 with the torque of a 4bt I not surprised to hear she turns the stock gears as well as if not better than a healthy 4.6. Thank you for the input.

@tager911 3 года назад

Hi. Your engine RPm gauge work from alternator or another sensor?

@Tinker1837 3 года назад

Alternator

@stephenpenland278 3 года назад

So at the fuel station the black handle is diesel and the green is petrol. I got to 76's and where I live its opposite.

@Tinker1837 3 года назад

I swear every other station does it different here... not ideal & part of why I put so many "diesel only" stickers on the fuel door.

@user-od6ip2sz5o 3 года назад

Наклей на металл кожу с мягкой подложкой, будет круто выглядить (под приборы)

@Tinker1837 3 года назад

Interesting idea!

@TheSandman614 3 года назад

Gonna put any indicator lamps in the dash?

@Tinker1837 3 года назад

I'm honestly not sure yet what I'll do for that... either drill holes in the this cluster for the warning lights + indicators, or setup a panel for those lights up on top of the cluster surround.

@ChristoforosGkekas 2 года назад

On my discovery doesn't work the rpm... what do you think is the problem?

@Tinker1837 2 года назад

For my Discovery I needed a RPM gauge that is adjustable.

@Fran-rp3lp 3 года назад

I'm planning to do something like this with my 1980 international s2554, cluster is cracked and gauges ain't working no more. Where can i buy a mechanical gauge set for a diesel engine????

@Fran-rp3lp 3 года назад

Yours is awesome btw

@Tinker1837 3 года назад

Thanks! And the gauges like I have from VDO also have mechanical versions & I found the best prices on Summit Racing. That's a proper big truck!

@blakeb5195 3 года назад

what about your blinker indicator?

@Tinker1837 3 года назад

I'm honestly not sure yet what I'll do for that... either drill holes in the this cluster for the warning lights + indicators, or setup a panel for those lights up on top of the cluster surround.

@naeemshaikh3552 3 года назад

What is the diesel average of 4bt on your vehicle

@Tinker1837 3 года назад

I do not know yet, but now with a gauge I can discover the fuel average.

@naeemshaikh3552 3 года назад

@@Tinker1837 Dear After your RnD please tell me diesel average definately. Because in our coutry diesel price goes very high & so what i am finding which engine i have to mount on my van or generator.👍👍

@Tinker1837 3 года назад

Absolutely, happy to share what I find :)

@naeemshaikh3552 3 года назад

@@Tinker1837 Jazakumullahu khair

@doorvanoijen2005 3 года назад

what is youre plan for the hood

@Tinker1837 3 года назад

It's a secret for now, but it's a fun idea that I think will be very unique.

@maxsav007 3 года назад

@@Tinker1837 😏😏

@7_7_5 3 года назад

is there a link to these gauges?

@Tinker1837 3 года назад

Now there is! www.vdo-gauges.com/instruments-displays-and-clusters/by-series/vision-black.html

@7_7_5 3 года назад

@@Tinker1837 Thank you very much!

@dave717785 3 года назад

Ah more like a finished vehicle everyday.

@Tinker1837 3 года назад

Yeah :D Did not expect the new gauge cluster to turn out this nice, but certainly makes it seem more legit in the cockpit now!

@alex2481a 3 года назад

Im thinking doing a swap on toyota tacoma 2017 any ideas ?

@vr6prodigy 3 года назад

Yes. Start working and don't stop till you're done lol

@kerrman91 3 года назад

2.8r, 4bt mucho gravity

@alex2481a 3 года назад

@@kerrman91 im traying a bt 4 thanks

@Tinker1837 3 года назад

The 4BT engine will be quite tall for that chassis but not impossible.

@alex2481a 3 года назад

@@Tinker1837 thanks

@josuesamuel497 3 года назад

How does the sensors work?

@Tinker1837 3 года назад

Which sensor?

@josuesamuel497 3 года назад

@@Tinker1837 temp sensor, rpm,volt, blinkers .😅

@Tinker1837 3 года назад

Temp sensor is in the cylinder head, rpm is coming from the alternator, voltage is just from the batteries, and blinkers I have not done (yet)

@lorddacb 3 года назад

All good, but please change the water temp gauge with rpm gauge PLEASEEEE.

@Tinker1837 3 года назад

But why? I kinda like that layout.

@lorddacb 3 года назад

@@Tinker1837 ahahh, Because it´s look more standard. RPMs bottom left, But if you like it thats fine lol

@Whiskydickwonder 3 года назад

Too bad about the engine paint flaking

@Tinker1837 3 года назад

Yeah, needs a redo for sure :(

@allenanthony4033 3 года назад

It’s time for A HooD she looking good sounding Good New name cum discover 🤔😎

@Tinker1837 3 года назад

Yes! Shoveling out my engine bay during winter could be challenging.

@aminationvidsmiyo6027 3 года назад

First

@Tinker1837 3 года назад

Eleventy!

@Vladimir-pl3qk 3 года назад

Where's the Tachometer

@Tinker1837 3 года назад

It's the gauge to the upper right side of the big center speedo gauge.

@Vladimir-pl3qk 3 года назад

@@Tinker1837 OK saw everything...

@Tinker1837 3 года назад

I am so excited to have them now so I can turn up the boost :D

@Vladimir-pl3qk 3 года назад

@@Tinker1837 and you've already connected the fuel level sensor ...

@Vladimir-pl3qk 3 года назад

@@Tinker1837 I would also add an indicator of air filter contamination

@MarkWright1963 3 года назад

Shane the bottom gauges don’t fit the bezel properly

@Tinker1837 3 года назад

They do, just that it's rather difficult to get a camera where the driver's eyes are when... driving