peugeot ECU Driver IC replacement 

Thanks for the reply.I play around alright but would like to get better understanding of components functionality and test methods.your channel is grate and knowledge to be able to fault find components 👍

With the help of a tape you can position and secure the ic easily and solder it .

Good job sir. From the Philippines thank you for sharing.

I am really looking forward to your video, you do great work

Good job. How we can order SMD component all type I work in BMW all type modules. But I have no link how to get new component so I try with old modules

In Toyota Yaris 2007 ECU where can I find immobilizer?

Hi could you tell me what's the most common part on ecu that gets damaged due to short circuit?

Good lesson the best sloving ECU board

What was the problem symptoms on the car, that required this driver to be replaced? Thanks

can we ask some questions about the 7 to 14 pins of ecu to formatter?

Sir i have a mitsubishi pajero 1999 model after put wrong jump start wrong wire now chek light not showing what happened in ecu

What kind of Gel Flux do you recommend?

hello what drive is for peugot 308 2009 and does bosch 30682 is a replacment for bosh 30680 thank you

what temperature did you use to desolder?

How did you figure out that was the trouble chip?

I have a 02 Peugeot 607 and the computer is burned, I want to know what I should do.

Hey man i have a 2008 peugeot 207 , they have common fault the the electronic power steering system , are you able to repair these ?

💐 thank you sir 👍🏻

pretty cool.nice work

Peugeot which model ecu? Is it 308 or others?

Great job!!!! If i am correct because i don t know NOTHING about this ... Did you take the chip off the dameged one and put it on a jused one so you don t have to code it? I have a bmw module and i boucht another one but from the same car but not a cabrio but the number en is the same but it is fore electric use of the doors and windows and roof ... But the other is not a cabrio si will this work (every litle thing is the same inside ... Please help 🥴😅

What kind of past are injectin there? Flux? Can you tell me the brand?

Great job

Sir aapne fluks kon si company ka use Kiya jb hm IC ko soldering krte h to IC ki aaps me leg ek doosre se touch ho jati h

Those fluxes your using are same for removing and soldering

Nice job👍🏻

Nice info, thanks

Hello Sir i need f6a t/c 2wd 4at 33920-74G8 1 ka wiring diagram plz

What function does that mar1909pd component have to do with the injectors???

is that signal input IC driver, that ypu replace?

Nice VDO. Nice hair!!!

Good job

What flux do you use?

Nice video😀

Hi. Can you tell me what was the error codes of the car? It's because I have a Peugeot 206 with the same ECU and the error is P0202 and P0203 and sometimes P0201 but it's not the injectors because I have substituted them. It only gives the error when I flore it rapidly. If I accelerate slowly it does not give the error. I can flore it to the red line and it stays good. It only throws the error is I am on low revs and flore it rapidly. I am puzzled by this because I think that if it was the driver the car would work on 3 cylinders or show some kind of failure and this does not happen. It only happens when I flore it from low revs. Thank you for your video and I will be waiting for your answer. Thanks.

Hello friend, I have that same icu in a 2002 Citroën C5, the signal does not reach injector 2 and 3, it comes from the computer. You will know which component you have to change.

Hi do you know of any good automotive electronic repair courses?Any help would be much appreciated.

Pro tip: if you dont remove the solder from the pin pads you can get the chip to just drop in place w/ the heat gun. 😜

hi bro i have a cuestion, how many degrees use for desoldering de ic.

Cooling fan is always on, even runs when engine is cold.. my mechanic said the problem is with the ECM board. is it so?

Hı dear İ have Peugeot et3j4 1.4 16v engine İ have a question for u When my car warms up to 90 celcius. Start my car idle surfing up and down and sometime stop my car suddenly.. im very bored this problem.. We have 5 friends having the same problem. Do you have a solution for us 😥 ? And im sorry for my bad English Best regards

Eek , that's a lot of aluminum to warm up . I'm guessing that's why you didn't use solder paste underneath ? Nice repair there.

Sir plz make video on replacement of infeneon tricore 2nd generation mcu any fixing process

Wrong soldering method chosen. Bottom of IC was unsoldered (just ends) and will have problems with heat dissipation.

To je divne pajeni,tenky hrot a pajet od cipu a hned je hezky zapajene a ne tak cik cak do krize a zas odsavat moc zbytecne zkratovani .😮

What funtion is that iC ?

ахренеть как долго и муторошно. на кой было убирать припой с дорог родной?

Babyyyyyyy THAT THONG TONG TONG TONGGG TONGGG YEAHHHHHH !!!!!!!!!!! LIKE IF YOU LIKE SISQOOOOO

Professional Job, not for the DIY Man!

🇧🇷🇧🇷🇧🇷🇧🇷👏👏👏👏👏

İstanbul da yaşıyorum proton 1600motor otomatik şanzuman 98 model araba var beyin arızası var nasıl tamir edebilirim??

I read the comments and everyone said thank you, how could you thank a video that shows only garbage and waste of time that trying to desolder and resolder a chip? That was the most talentless soldering I have ever seen.

Professionalität kann man das nicht nennen, was hier gezeigt wird.

Kindly don't have the "music" we rather listen to you.

shit welds

ONE OF THE WORST WAY TO SOLDER THIS KIND OF CHIP ( HEAT SINK PADDED) YOU RUINED THERMAL CONDUCTIVITY

Good job