PlayStation 5 HDMI port replacement 

Hello, I want to say Thank you to you. My old laptop stopped working yesterday. After checking the psu was working and the charging light was on, I did the measurement from a usb port which suggested no motherboard fault. I opened the case, I saw the pcb battery and took it out, put it back in after 10 mins. Bingo, all fired back to life. I feel you gave me the confidence to attempt this. Thank you.

You are Amazing man sir I have had passion for electronics and electrical maintainance and installation all of you sharing knowledge on you tube for free are amazing I have learnt a lot from you sir God bless you and your entire family

It's possible that the PS5 was set to 4K or some other display setting that your capture card or the display at your desk doesn't support. If you turn it on by holding the power button down for 6 seconds it should boot into safe mode, which should display on any device. Just for future reference!

Thank you very much for this video, Sorin. With your help, another PS5 lives again. Your method worked really well, only thing I changed was I pre tinned the pins of the port first and made sure I had nice fluffy pillows of fresh solder and flux on the pads which seemed to help with less pins to touch up at the end. Hell of a ground plain on these eh !

When the professor has to watch a tutorial 🤣🤦

The most realistic video for replacing hdmi port for PS5 👍🏼 i like it thanks for sharing. I think i overheat my PS5 board during my try to replace the same

10:36 lol , you're amazing

Huge gaming Machine. As I remember how I was putting radiators and fans everywhere on my daughter's computer 😭

Just done 2 of these yesterday, so many screws

BOM clerk to PS5 engineer: "How many screws to do you need?". "Yes".

Love the scottish accent when ranting on screw-sizes.

You're such a nice guy sir thanks for sharing all of your ideas hat's off to you sir💯

For little bit more stress you can use low melt solder before hot air

Nice repair video 👏

Great job. What are you going to do now with all these screws !!! Good luck 😃

I know with the PS3 & the PS4, HDCP settings in the software won't allow you to capture from the Elgato so I assume that was the case here.

Not sure what I'm doing wrong but I've done exactly like you've done here 500 degrees 100% airflow on my rework station to try and remove a HDMI port from a laptop motherboard - after 5 minutes I give up as it's just not budging! Melted, but not budging :(

That is some amazing RF shielding for the PlayStation.

Unique content. 👌🏼

good job mate.

Japanese engineering : They use the minimum requirements screw length so different sizes for each. 😂😂

Could it be your HDMI cable? Fairly certain there are different revisions of HDMI. Nice vid. Friend of mine asked if I could replace an xbox one hdmi. Was just something they seen on fb marketplace. Should of bought it and fixed it. Don't have much soldering experience though and I'd need a heat gun and finer tip.

Sorin why don't you use solder wick to remove solder and get clear holes then just press connector and solder 4 big legs after that just put flux and pass over all little conectors job done...💁

the screws are different sizes because of the design of the case

is the capture card 4K capable? the PS5 might be on 4K.

my question is what is the best alternative for flux if you cant find it at the store or it is too expensive?, thankyou for sharing :)

you say your goal is 50 with the helium , how high could it go for you, could get up to 200 per day?

Wish he show reassembly.

Let's replace hdmi ports fast. I laughed the very minute he said that. 60 odd screws later...........

Soren, why don't you take a minute to blow out the dust from the fan while you have the laptops open? Your customers will notice when their computers are a bit faster. Or much faster (and quieter) if the dust (and hair.....) is really thick. Also, why not replace the thermal paste (if it is dried up) when you remove heatsinks from GPUs and CPUs. I know that time is money, but it doesn't take long and happy customers will always come back and tell all of their friends. I really like your videos and I realize that some of your "doggy" fixes are the most feasible solutions and will likely work just fine, so my comment is not meant to criticize your work.

Helium balloons rising 😁

Dont lose the spacer!!

Hi Sorin, I need a bit of help. I have a Asus TP301UA, came in to change the screen, when I open it to unplug the battery before dismounting the screen, I noticed that near the lvds connector its burned, typical for when the cable is unplugged while connected. It looks like a capacitor, but what its burned its looks like an inductor or a coil. I cant locate the schematic, all I could find its a photo of the board where I could see how the components supposed to look like. I could send you a picture, but I guess its typical for the 19V lvds.

What happens if you get the liquid metal on the motherboard?

Do you know where I can get hdmi replacement plug already tined?

He's probably still trying to reassemble :)

Please Help sir !!! I installed windows 10 on dell Inspiron n5010 Then downloaded drives from dell website Duing bios update from Version a5 to a15 screen went white then laptop was off Tried to reset bios by removing bios battery and holding down power button and nothing happened Watched a video about installing bios files on a fat usb flash drive then holding end till plugging the power supply and that a bios installation will be performed automatically but in video only the screen was off but lights were on and laptop was beebing In my case everything is off no sounds no lights nothing Regards from Syria i follow you since long time.

Good friggin luck on those screws...

Sorin please check the Hakko Gx 951 clones for under 50 usd/pounds they use direct heat tips and they have really really good thermal performance and with really really fast heat up.

you are besr Techer, Thinks My Uncle 😁,

awesome

Are you located in the US? I have a laptop I'd pay you to fix

Can anyone here tell me why is Mr. Sorin ignoring my request for his shop's address in the UK ? Thanks Y'all a million .

Anyone know the address of the shop repairing

did he just put a ps4 hdmi port on a ps5? the hdmi port is 2.1 on the ps5🤔

Jesus Christ is coming back very soon stay prayed up and have a blessed day🤍

Time for a new microscope camera Sorin? :)

My professor you must change cable HDMI your one

from phillipines

PlayStation fans: please becareful

That an SSD expansion port

nice

I hope you will put a new thermal paste and liquid meta when you finish the job and collect all in one peace. Its true right?

The correct way to change ANY port is wick off the old solder, put the new port in place and then solder by hand. Then you know for sure the port is soldered correctly and there will be no heat damage. Try it next time and it will be a better job and be faster because you will not waste time taking it apart and going over your work 3 times ^_^

Wow loads of screws .Nice video

help me im technician from phillipine im ur number fan for repairing laptop sir

I need my ps5 fix

hello po

HI, can i be unbanned from discord my account got hacked, and now i think im banned, i cannot join

you need a new tv

❤❤2

Helium: The Sky is the Limit! 😁

Someone please gift him JAKEMY Y02 PLUS electric screwdriver. Its impossible for me to send him from country.

HDMI booster - that why not working.

Dodgy port replacement. 🥲