Plumbing - Avoid Doing This! What Was I Thinking?

Подписаться 10 тыс.

Просмотров 5 тыс.

50% 1

Plumbing you've gotta think outside the box but there is a fine line between that and cutting corners! In this week day in the life of a plumber we are installing a cylinder but when we come to fit it we have to make a judgement call on the job which in hindsight i wouldn't recommended or do again myself. We have a direct cylinder to replace that has split, unfortunately for customer they called us after getting an emergency plumber in to remove, which cost the near enough the same price as the replacement! We also got a top tip from the customer on how to isolate the horstmann clock that was in that we didn't know, every days a school day in plumbing!
Lastly we will show you the results from the system clean, we replaced a main heat exchanger in the last episode and in this one and left some cleaner in, i asked if you wanted to see it and decided the include it on this one so hope that helps
Thanks again for all your support
Subscription Goal 9420/10,000
#plumbing #howto #plumber
Check the links below if you considering any work wear from Big Boots might save yourself a few quid
BIG BOOTS 10% OFF LINK BELOW OR USE BULLDOG10 AT CHECKOUT
www.bigboots.co.uk/discount/B...

Хобби

Опубликовано:

19 май 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 42

@bluebulldog_uk 2 месяца назад

Let me know a time when your head wasn’t in gear…own your mistakes…I did get lucky this time 😅😅 thanks for your support as always 🙌👍

@andrewhoughton2617 2 месяца назад

Started filling the system and forgot to close the rad vents in a couple of rooms last week. Such a schoolboy error. I was so embarrassed 😞

@YoutubeHero666 2 месяца назад

On my maganacleanse I had not checked the how tight the hose clips were for a while and halfway through the clean one popped off and flooded the kitchen! I had the unit sitting over the hob so that got soaked aswell. I always tighten them each time or at least check if tight! Customer was fine and helped me clean up :)

@russellbaldry5095 2 месяца назад

I once unsoldered a live gas pipe thinking it was the heating return…….lets just say the flame thrower effect was an eye opener😳🤦🏼‍♂️🤷🏼‍♂️

@alimack5489 2 месяца назад

When first starting out after finishing my apprenticeship and thinking was was amazing and qualified… drained down boiler to change a flow turbine, didn’t turn the mains off… customer comes downstairs to a flooded kitchen me soaked and a very wet and dead boiler. Turns out I didn’t have a clue… 🤦‍♂️ no idea why I thought I’d need to drain the boiler to this day.

@grajay155 4 дня назад

I've watched several of your videos, and these's a common theme that seems to be running through them. Mistakes! Some of them are painful to watch. I do hope you get better, as you seem to be a genuine guy with a lot of bad luck.

@bluebulldog_uk 2 дня назад

Yeah mate straight forward plumbing no one watches or finds interesting plus half the stuff you see happens to everyone, just want my channel to show the situations you can put yourself in or be found in, I can easily edit the videos to show no mistakes but no one is learning from that. Most of my work is straight forward and goes absolutely fine but doesn’t make good content

@philipmorris9761 Месяц назад

Thanks for sharing your mistake with the hole saw and spade bit scenario, with me building up my tools this will save me having to payout twice. Nice one for sharing the information about how you do a magna-cleanse, I was a bit baffled when it requested to partially fill the rads in the instructions. Continue to keep it real as you do bud much appreciated, I am almost at the point where I will be able to make donations to your channel and will get there even quicker with you advising what not to try as well as showing best practice. Great Video.

@bluebulldog_uk Месяц назад

Thanks for the support mate glad the videos am helping, with the rads being half full I didn’t understand it either untill ADEY showed me a demo and it made perfect sense 👍 yeah the hole saw was one of them moments but thought if I show how NOT to do it, might save someone a headache 😂👍

@richardranson9449 2 месяца назад

I always use a stepped drill got more control. Love the video keep them coming. Thanks

@bluebulldog_uk 2 месяца назад

Will have a look into one thanks for the advice mate 🙌👍

@jacquelinestanyer8533 Месяц назад

🔵🔵🔵 great video open and honest 🔵🔵🔵🔵🔵

@SteveHit1 2 месяца назад

Great video, thanks! I think the best cutters for sheet metal are Q-Max punches, but these do need access to both sides of hole. Especially good if you need to cut a hole in a stainless sink- they give a very clean, burr free, cut.

@bluebulldog_uk 2 месяца назад

Nice mate will have a look into them 👍

@user-li8gr8ur8l 2 месяца назад

Top job as usual Luke made it look easy ❤❤❤

@bluebulldog_uk 2 месяца назад

Thanks mate 🙌👍

@stephenharris5519 2 месяца назад

Excellent video as usual. Keep up the good work.

@bluebulldog_uk 2 месяца назад

Thanks mate 👍

@b1h2u3p4 2 месяца назад

Nice job 👏

@bluebulldog_uk 2 месяца назад

Thanks mate 👍

@YoutubeHero666 2 месяца назад

on your first hole I thought you were risking it! cheers for the content its great mate.

@bluebulldog_uk 2 месяца назад

You know what mate…so did I 😂 I still tried the 2nd one thou like an idiot…seemed like a good idea at the time thou

@tirvplumbing 2 месяца назад

We use the Starrett holesaws at work Luke. Don't last too long on steel beams or concrete fireboard but for plaster, wood and thin metal they're ok. 👍

@bluebulldog_uk 2 месяца назад

I will have a look at them mate, 100% be better than what I tried 😂👍