No video :(

Polaris Matryx DIY tunnel cut

Подписаться 3,7 тыс.

Просмотров 8 тыс.

50% 1

Polaris introduced the all new Matryx mountain sled for 2022. Tunnel redesign with the tapered extension was a welcome new design to help deep snow performance. How much the tunnel drags behind you in the snow can be a detriment to the skilled mountain rider and cutting length off the tunnel has become a common modification. Now that the tunnel coolers don't run all the way back on the Matryx, a tunnel cut is easier than ever.

Опубликовано:

29 авг 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 20

@mack73powslayer78 Год назад

Great video and so thorough as usual! Your channel needs more attention for the amount of work you put in. This is the best DIY channel out there for doing quality modifications on sleds 👍

@fnatomagan Год назад

Excellent job!

@mountainsleddergarage8627 Год назад

Thanks, glad it was helpful

@dallaswiller Год назад

Exactly what I was looking for. Thanks

@mountainsleddergarage8627 Год назад

Cool little mod, easy to do on the matryx

@bridgerlabau Год назад

This video is perfect thank you!!

@mountainsleddergarage8627 Год назад

Thanks!

@Pellerinbrad60 Год назад

Great video

@mountainsleddergarage8627 Год назад

Thanks! In the process to a removable snow flap option.

@shanesmith6242 Год назад

Thanks for the video, been wanting to do this to my slash as I found it just a little too long last year dragging the bumper and even exploded a tail light housing. I like my bumper directly over center of the axle. One question? Couldn't a guy just take a compass scribe set it to 3" and follow the lines of the rear tunnel piece speeding up the process and eliminating some room for error that is there by using painters tape and measurements?

@mountainsleddergarage8627 Год назад

Yes, there’s a number of different ways to do it. Just want to make sure it’s 100% where you want it and makes correctly before you cut.

@rhockeydude10 Год назад

cool very good video

@mountainsleddergarage8627 Год назад

Thanks! Not for everyone, but it’s a cool and simple mod if you’re an extreme mountain rider.

@reednoyd8605 Год назад

Great work. What size rivets did you put in to attach the extension piece on the tunnel? Were they factory from Polaris? Trying to figure out what I need to order. Thanks

@mountainsleddergarage8627 Год назад

I just used standard 3/16 pop rivets

@Rickydbaby Год назад

Did you drill and tap new holes in the bumper to re mount it? Or drill new holes in the tunnel? Seems like on the non slash I will need to cut my bumper down but then need to drill and tap some new holes in it. Hmm

@mountainsleddergarage8627 Год назад

I used an aftermarket bumper. If I was going to use the factory bumper I would just drill new holes to match up the threaded holes in the factory bumper.

@Rickydbaby Год назад

@@mountainsleddergarage8627 yea that's what I'm thinking. Except that the factory bumper will protrude way down into the running boards. I may cut some of it off.

@MolsonM3 Год назад

I have a 165 slash boost. Is it possible to measure a 155 slash tunnel and cut off that exact amount and then run the 155 slash backwoods bumper? I wanted to get a 155 but could only get a 165 this year.

@mountainsleddergarage8627 Год назад

Yes you can. You could get the bumper and then cut off what you need to fit the bumper