My axles were purchased used and exposed to lots of grime rolling around on a shop floor. I decided I should inspect the CV joint, clean, assemble and re-grease everything before I install it back in the car.
Patreon / ahhgaragetime
Insta @ahhgaragetime
FB / ahhgaragetime
Website www.ahhgaragetime.com
Below is a table of contents of past episodes 1-35. Click the link below for the rest
www.ahhgaragetime.com/TOC
Intro
Stripped Shell Introduction
• Porsche 911 Longhood C...
1
Drivers Fender Backdate, Unfold short hood edge, Make Signal Box Parts From Flat Sheet
• Backdating My Porsche ...
2
Drivers Fender Signal Box, Shape Bottom Portion w/ Bead Roller
• Porsche 911 Metal Fabr...
3
Drivers Fender Side Patch Panel Hammerform, TIG Weld Signal Housing
• CNC Machined Hammerfor...
4
Drivers Fender TIG Weld Side Patch Panel, Add signal housing triangle piece
• TIG Welding Sheetmetal...
5
Passenger Side Fender Backdate, Additional Content From Driver's Side
• Modify Your Short Hood...
6
Shorthood to Longhood Conversion, Form Outer Skin Edges And Weld On
• Project Porsche 911, L...
7
E Wheel and Form Longhood Inner Skin w/ Handormed Strength Rib
• English Wheel Metalsha...
8
TIG Weld Outer and Inner Longhood Extension
• Porsche 911 Restoratio...
9
Longhood Front Seal Custom Bracket
• Porsche 911 Carrera RS...
10
Rear Backdate, Remove Rear Impact Bumper and Valence
• Porsche 911 RS Tribute...
11
Lead Rear Valence Corners, Rear Latch Panel Backdate
• Porsche 911 Outlaw Bui...
12
Hybrid Steel License Plate panel & Fiberglass Rear Bumper, Custom Panel Brackets
• Porsche 911 Build - Hy...
13
Custom Aluminum Rear Bumperettes, Solidworks Design, Cut on CNC machine, Rear Flare Trial Fit
• Old Porsche 911 Resto ...
14
Form and TIG Weld Custom Rear Aluminum Bumperettes, Rear Bumper Complete
• Old Porsche 911 Resto ...
15
SC to RS Flare Comparison, Photoshop & Sheetmetal Conversion to RS
• How to Spot a SC Fende...
16
Tack Weld Passenger Side RS Rear Flare, Remove Undercoat, Align Flare
• How to Butt Weld a Ste...
17
Weld Passenger Side Flare, TIG VS MIG, Planishing, Weld Distortion, TIG Arc shots
• Porsche 911 Build - We...
18
Align Body Panels, Hood gaps, Adjust tub with dumbell, Repair Rocker, gap tool, Windshield fit check
• How to Align Body Pane...
19
Fill 20+ Holes, Mirror, Washer Jets, Rockers, Gas Filler, Antenna,
• How to Fill Holes in Y...
20
Remove Rear Window without cutting seal, Kick Method
• How to Remove Porsche ...
21
Remove Decklid Bumps and adjust Gaps & Fit, Add Weld material to edge
• Porsche 911 Decklid Pa...
22
Weld Pssgr Fender Support Panel, Lead Hood to Fender Gap, Weld Fender Edge to Reduce Gap
• Perfect 3mm Door Gaps ...
23
Build quality, Improve Panel Fit, Lead Passenger Door Gap, Lead Rocker to fender gap, Drivers Door
• Who Doesn't Want High ...
24
Drivers Door Alignment, Fill Rust Pits with TIG, Lead Drivers Door Gap, Adjust Front Fender Signal Fit,
• Panel Alignment Nightm...
25
Discovered Rust in Suspension Pan, Spot Weld Drilling, Tram Guage Mounting Points, cut out pan
• Rust Repair is HARD on...
26
Suspension Pan Repair, remove suspension, Cut Latch Panel for Oil Cooler, Check Squareness
• Suspension Pan Replace...
27
Align and Weld Suspension Pan, Spirit Level to remove twist, Kettle Bell Hits to Tweak Position, Rosette Welds
• 911 Suspension Pan Wel...
28
Re-Align Hood/Tub after Suspension Pan Install, Repair rust on gas tank panel,
• 911 Gas Tank Panel Rep...
29
Gas Tank Support Welded In, De-rusted with Electrolysis Bath, Reshaped pan edge, Final welding
• How to Simulate Factor...
30
Simulate Factory Spot Welds, Rosette Plug Welds, Pencil eraser on primer
• How to Simulate Factor...
31
Convert Drivers Side Flare to RS Profile and Repair Rust Damage
• Porsche Restomod - RS ...
32
TIG Weld Drivers Side Flare, Remove Failed Undercoating in Wheel Well, Planish and Metal Finishing
• 911 Restomod | This is...
33
Strip Paint from Car and Prep for Epoxy Primer, Strip it disc and paint stripper
• How to Beat the Ugly O...
34
Epoxy Prime, Project Review and Cost Reveal
• My Cheap Porsche Gets ...
35
Rear Coilover Gussetts & X-member strengthening plates, Golf Ball Dimple Dies For Speed Holes,
• How To Make Your Porsc...
~-~~-~~~-~~-~
Please watch: "Automotive Suspension Part 3D Scan with Revopoint Range Scanner"
• Get A Perfect 3D Scan ...
~-~~-~~~-~~-~
25 авг 2024
