Time to assemble some shiny parts on my project 911. New stainless fuel lines routing through the tunnel plus the steering is now fully rebuilt from the steering wheel to the tires.
I replaced a bad bearing in the steering shaft which to be honest wasn't easy to remove. Luckily it was the $6 bearing and not the $75 bearing that was faulty.
My custom fuel lines went in okay, but it's important to prep the end with something smooth before you fish it through.
Lots of good tips in this video and I definitely recommend you check your fuel lines before its too late.
URO Steering Coupler
amzn.to/2Wjk4Rc
Patreon / ahhgaragetime
Insta @ahhgaragetime
FB / ahhgaragetime
Website www.ahhgaragetime.com
Merchandise: ahhgaragetime.com/ahh-garage-...
Below is a table of contents of past episodes 1-35. Click the link below for the rest
www.ahhgaragetime.com/TOC
Intro
Stripped Shell Introduction
• Porsche 911 Longhood C...
1
Drivers Fender Backdate, Unfold short hood edge, Make Signal Box Parts From Flat Sheet
• Backdating My Porsche ...
2
Drivers Fender Signal Box, Shape Bottom Portion w/ Bead Roller
• Porsche 911 Metal Fabr...
3
Drivers Fender Side Patch Panel Hammerform, TIG Weld Signal Housing
• CNC Machined Hammerfor...
4
Drivers Fender TIG Weld Side Patch Panel, Add signal housing triangle piece
• TIG Welding Sheetmetal...
5
Passenger Side Fender Backdate, Additional Content From Driver's Side
• Modify Your Short Hood...
6
Shorthood to Longhood Conversion, Form Outer Skin Edges And Weld On
• Project Porsche 911, L...
7
E Wheel and Form Longhood Inner Skin w/ Handormed Strength Rib
• English Wheel Metalsha...
8
TIG Weld Outer and Inner Longhood Extension
• Porsche 911 Restoratio...
9
Longhood Front Seal Custom Bracket
• Porsche 911 Carrera RS...
10
Rear Backdate, Remove Rear Impact Bumper and Valence
• Porsche 911 RS Tribute...
11
Lead Rear Valence Corners, Rear Latch Panel Backdate
• Porsche 911 Outlaw Bui...
12
Hybrid Steel License Plate panel & Fiberglass Rear Bumper, Custom Panel Brackets
• Porsche 911 Build - Hy...
13
Custom Aluminum Rear Bumperettes, Solidworks Design, Cut on CNC machine, Rear Flare Trial Fit
• Old Porsche 911 Resto ...
14
Form and TIG Weld Custom Rear Aluminum Bumperettes, Rear Bumper Complete
• Old Porsche 911 Resto ...
15
SC to RS Flare Comparison, Photoshop & Sheetmetal Conversion to RS
• How to Spot a SC Fende...
16
Tack Weld Passenger Side RS Rear Flare, Remove Undercoat, Align Flare
• How to Butt Weld a Ste...
17
Weld Passenger Side Flare, TIG VS MIG, Planishing, Weld Distortion, TIG Arc shots
• Porsche 911 Build - We...
18
Align Body Panels, Hood gaps, Adjust tub with dumbell, Repair Rocker, gap tool, Windshield fit check
• How to Align Body Pane...
19
Fill 20+ Holes, Mirror, Washer Jets, Rockers, Gas Filler, Antenna,
• How to Fill Holes in Y...
20
Remove Rear Window without cutting seal, Kick Method
• How to Remove Porsche ...
21
Remove Decklid Bumps and adjust Gaps & Fit, Add Weld material to edge
• Porsche 911 Decklid Pa...
22
Weld Pssgr Fender Support Panel, Lead Hood to Fender Gap, Weld Fender Edge to Reduce Gap
• Perfect 3mm Door Gaps ...
23
Build quality, Improve Panel Fit, Lead Passenger Door Gap, Lead Rocker to fender gap, Drivers Door
• Who Doesn't Want High ...
24
Drivers Door Alignment, Fill Rust Pits with TIG, Lead Drivers Door Gap, Adjust Front Fender Signal Fit,
• Panel Alignment Nightm...
25
Discovered Rust in Suspension Pan, Spot Weld Drilling, Tram Guage Mounting Points, cut out pan
• Rust Repair is HARD on...
26
Suspension Pan Repair, remove suspension, Cut Latch Panel for Oil Cooler, Check Squareness
• Suspension Pan Replace...
27
Align and Weld Suspension Pan, Spirit Level to remove twist, Kettle Bell Hits to Tweak Position, Rosette Welds
• 911 Suspension Pan Wel...
28
Re-Align Hood/Tub after Suspension Pan Install, Repair rust on gas tank panel,
• 911 Gas Tank Panel Rep...
29
Gas Tank Support Welded In, De-rusted with Electrolysis Bath, Reshaped pan edge, Final welding
• How to Simulate Factor...
30
Simulate Factory Spot Welds, Rosette Plug Welds, Pencil eraser on primer
• How to Simulate Factor...
31
Convert Drivers Side Flare to RS Profile and Repair Rust Damage
• Porsche Restomod - RS ...
32
TIG Weld Drivers Side Flare, Remove Failed Undercoating in Wheel Well, Planish and Metal Finishing
• 911 Restomod | This is...
33
Strip Paint from Car and Prep for Epoxy Primer, Strip it disc and paint stripper
• How to Beat the Ugly O...
34
Epoxy Prime, Project Review and Cost Reveal
• My Cheap Porsche Gets ...
35
Rear Coilover Gussetts & X-member strengthening plates, Golf Ball Dimple Dies For Speed Holes,
• How To Make Your Porsc...
1 май 2020
